White Balance Adjustment - LG 47LN613 Series Service Manual

4.1.2. 2D EDID
▪ Reference
- HDMI1 ~ HDMI4 / RGB
- In the data of EDID, bellows may be different by S/W or
Input mode.
ⓐ Product ID
HEX EDID Table
0001
0001
ⓑ Serial No: Controlled on production line.
ⓒ Month, Year: Controlled on production line:
ex) Monthly : '01' → '01'
Year : '2012' → '16'
ⓓ Model Name(Hex): LGTV
Chassis
LD33B 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20
ⓔ Checksum(LG TV): Changeable by total EDID data.
ⓔ1
HDMI1 43
HDMI2 43
HDMI3 43
ⓕ Vendor Specific(HDMI)
INPUT MODEL NAME(HEX)
HDMI1 67 03 0C 00 10 00 80 2D
HDMI2 67 03 0C 00 20 00 80 2D
HDMI3 67 03 0C 00 30 00 80 2D

4.2. White Balance Adjustment

4.2.1. Overview
▪ W/B adj. Objective & How-it-works
(1) Objective: To reduce each Panel's W/B deviation
(2) How-it-works : When R/G/B gain in the OSD is at 192, it
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one
of R/G/B is fixed at 192, and the other two is lowered to
find the desired value.
(3) Adjustment condition : normal temperature
1) Surrounding Temperature : 25 °C ± 5 °C
2) Surrounding Humidity : 20 % ~ 80 %
4.2.2. Equipment
(1) Color Analyzer: CA-210 (LED Module : CH 14)
(2) Adjustment Computer(During auto adj., RS-232C protocol
is needed)
(3) Adjustment Remote control
(4) Video Signal Generator MSPG-925F 720p/216-Gray
(Model: 217, Pattern: 78)
→ Only when internal pattern is not available
▪ Color Analyzer Matrix should be calibrated using CS-1000.
Copyright © LG Electronics. Inc. All rights reserved.
Only for training and service purposes
DDC Function
0100 Analog
0100 Digital
MODEL NAME(HEX)
ⓔ2 ⓔ3
15 X
05 X
F5 X
4.2.3. Equipment connection MAP
Probe
4.2.4. Adj. Command (Protocol)
<Command Format>
START 6E A 50 A LEN A 03 A
- LEN: Number of Data Byte to be sent
- CMD: Command
- VAL: FOS Data value
- CS: Checksum of sent data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
▪ RS-232C Command used during auto-adjustment.
RS-232C COMMAND
[CMD ID DATA]
wb 00
wb 00
wb 00
wb 00
wb 00
wb 00
Ex) wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f → Gain adj. completed
*(wb 00 20(Start), wb 00 2f(end)) → Off-set adj.
wb 00 ff → End white balance auto-adj.
▪ Adj. Map
Applied Model : LD33B Chassis ALL MODELS
Adj. item
R Gain
G Gain
B Gain
Cool
R Cut
G Cut
B Cut
R Gain
G Gain
B Gain
Medium
R Cut
G Cut
B Cut
R Gain
G Gain
B Gain
Warm
R Cut
G Cut
- 16 -
Co lo r Analyzer
Co m p ut er
RS -232C
Pat t ern Generat o r
Signal Source
* If TV internal pattern is used, not needed
CMD A 00 A VAL
Explantion
00 Begin White Balance adjustment
10 Gain adjustment(internal white pattern)
1f Gain adjustment completed
20 Offset adjustment(internal white pattern)
2f Offset adjustment completed
End White Balance adjustment
ff
(internal pattern disappears )
Command Data Range
(lower caseASCII) (Hex.)
CMD1 CMD2 MIN MAX
j g 00 C0
j h 00 C0
j i 00 C0
j a 00 C0
j b 00 C0
j c 00 C0
j d 00 C0
j e 00 C0
j f 00 C0
LGE Internal Use Only
RS -232C
RS -232C
A CS STOP
Default
(Decimal)