Related Manuals for DeWalt DC545-XE
Summary of Contents for DeWalt DC545-XE
- Page 1 INSTRUCTION MANUAL DC545-XE, DC546-XE, DC547-XE HEAVY-DUTY 18V CORDLESS ADHESIVE GUN...
-
Page 3: Definitions: Safety Guidelines
1. WORK AREA Definitions: Safety Guidelines a. Keep work area clean and well lit. Cluttered and dark areas invite accidents. b. Do not operate power tools in explosive atmospheres, such as in the The definitions below describe the level of severity for each presence of flammable liquids, gases or dust. -
Page 4: Electrical Safety
d. Remove any adjusting key or wrench before turning the power tool on. A 5. BATTERY TOOL USE AND CARE wrench or a key left attached to a rotating part of the power tool may result in a. Ensure the switch is in the off position before inserting battery pack. Inserting personal injury. -
Page 5: Extension Cords
Extension Cords • ANSI S12.6 (S3.19) hearing protection, • NIOSH/OSHA/MSHA respiratory protection. CAUTION: Use only extension cords that are approved by the country’s Electrical Authority. Before using extension cords, inspect them for loose or exposed wires, WARNING: Some dust created by power sanding, sawing, grinding, drilling, and damaged insulation and defective fittings. -
Page 6: Important Safety Instructions For Battery Packs
DANGER: Electrocution Hazard. Never attempt to open the battery pack for any ....Class I Construction .....earthing terminal reason. If battery pack case is cracked or damaged, do not insert into charger. Electric ....(grounded) .....safety alert symbol shock or electrocution may result. Damaged battery packs should be returned to .... -
Page 7: Important Safety Instructions For Battery Chargers
Important Safety Instructions for Battery Chargers using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. SAVE THESE INSTRUCTIONS: This manual contains important safety instructions MINIMUM GAGE FOR CORD SETS for battery chargers. -
Page 8: Charge Indicators
up weekly or after 10 charge/discharge cycles or whenever the pack no longer Indicator Light Operation delivers the same amount of work. To use the Automatic Tune-Up™, place the battery pack in the charger and leave it for at least 8 hours. The charger will cycle through the following modes. -
Page 9: Important Charging Notes
WEAK BATTERY PACKS: Chargers can also detect a weak battery. Such batteries WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric are still usable but should not be expected to perform as much work. In such cases, shock may result. -
Page 10: Installing And Removing The Battery Pack
FIG. 1 OPERATION Installing and Removing the Battery Pack NOTE: Make sure your battery pack is fully charged. CAUTION: To prevent inadvertant operation, lock trigger switch before removing or installing battery. To install the battery pack into the tool handle, align the base of the tool with the notch inside the tool’s handle and slide the battery pack firmly into the handle until you hear the lock snap into place (Fig. - Page 11 Trigger Switch Lock-off (Fig. 1) To Insert Material NOTE: Material left in the cartridge/sausage holder may dry if left unattended. Follow WARNING: Turn unit off and disconnect battery pack before installing and manufacturer’s recommendations when using caulk or adhesive material. removing accessories, before adjusting or when making repairs.
- Page 12 FIG. 5 FIG. 4 FIG. 6 310 ML CARTRIDGE HOLDER FIG. 7 600 ML SAUSAGE HOLDER...
- Page 13 SAUSAGE HOLDER (FIG. 4) 3. Press and hold the plunger rod release trigger (A) and push the plunger rod (G) forward to access the threads on rod. Release the trigger. 1. Unscrew nozzle cap (M) and remove nozzle (N). 4. Thread the sausage holder (L) onto the rear cap (U). 2.
- Page 14 CHARGER CLEANING INSTRUCTIONS This warranty does not apply to • Accessories WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a • Damage caused where repairs have been made or attempted by others. cloth or soft non-metallic brush.
- Page 16 WALT Battery and Charger Systems Battery Output Chargers/Charge Time Nominal 240 Volts 12 Volts Cat. Number Voltage Amp Hour 97014 98014 DW9106 DW9107 DW9108 DW9115 DW9116 DW9117 DW9118 DE9116 DE9118 DW911 DC011 DW0245 DE2046 DE9000 DW9109 DW0242 DE0240-XJ DW0240 DW9096 DE9095-XJ DE9091-XJ 14.4...