Page 1
Post this information in a prominent location. Keep this Manual in a Convenient Location for Reference Quality Equipment For The Restaurant, Supermarket, and Bakery Industries Anetsberger Brothers, Inc. GoldenGRILL GoldenGRILL GoldenGRILL...
Read these specifications, Code Requirements, Installation Requirements, Instal- lation Instructions, and Operating Instructions very carefully. Failure to follow the Instructions could cause the grill to malfunction. A grill malfunction can result in property damage, serious bodily injury, or death. SHIPPING CONT SHIPPING CONTAINER INSPECTION SHIPPING CONT SHIPPING CONT...
GRILL GAS SUPPLY SPECIFICATIONS Please make sure that your desired grill location has gas supply factors that are suitable for this product: MANIFOLD PRESSURE SUPPLY PRESSURE - Measured at tap on back side of gas manifold. - “ W.C. = Inches, Water Column. - Measure supply pressure ahead of pressure regulator when all other gas-powered equipment is operating.
CODE REQUIREMENTS CODE REQUIREMENTS CODE REQUIREMENTS CODE REQUIREMENTS CODE REQUIREMENTS IMPORTANT: Read the Code Requirements and the Installation Requirements and Instructions carefully, before starting the installation. Contact ANETS (800/ 837-2638) if any problems or questions arise. The grill installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition);...
INSTALLA INST INST ALLA ALLATION REQ ALLA INST INST ALLA nstall the grill in accordance with the preceding Code Requirements, as well as the following Installation Requirements. 1. DO NOT install this grill in a mobile home, trailer, or recreational vehicle. 2.
GRILL OPERA GRILL OPERA GRILL OPERATING INSTR GRILL OPERA GRILL OPERA DO NOT operate this grill during an interruption of gas service. Turn all grill controls to OFF, including the gas control valve knobs, then close the gas supply line valve. When notified that the gas service has resumed, perform the Lighting Procedure descibed below.
GRILL PREP GRILL PREPARA GRILL PREP GRILL PREP GRILL PREP MANUAL AND STANDARD GRILLS ONLY Conditioning Instructions - MG & SG Models ONLY 1. Upon examination of your grill you will notice that the grill plate is covered with a protective grease. To remove this grease, turn grill thermostats to about 250°F setting (or low setting on manually operated grills).
D D D D D AIL AILY CLEANING PR Y CLEANING PROCEDURE Y CLEANING PR Y CLEANING PR Y CLEANING PR Standard Grill Cleaning Instruction (MG & SG Models Only) 1. Clean grill plate often to prevent sticking and poor quality of product. 2.
GRILL GRILL TR GRILL GRILL GRILL All service (repairs or part replacement) must be performed by a qualified Service Agency. PROBLEM Pilot (piezo-electric) 1. Check if igniter is generating a spark. pushbutton igniter does not light the pilot flame. 2. Check for loose spark wire or igniter nut. 3.
Page 11
GRILL GRILL GRILL TR TROUBLESHOO OUBLESHOO OUBLESHOOTING GUIDE OUBLESHOO GRILL GRILL OUBLESHOO PROBLEM Main burners do not 1. Check that gas control valve is set to ignite. “ON”. 2. Check that pilots are burning. 3. Increase temperature setting on thermostat control. 4.
GRILL GRILL GRILL TR TROUBLESHOO OUBLESHOO OUBLESHOO OUBLESHOOTING GUIDE GRILL GRILL OUBLESHOO PROBLEM (Continued) 5. Check gas supply pressure with all Grill plate is cold (Burners not firing). 6. Observe if main burners are firing. 1. Check that thermostat control Grill plate is not hot enough.
No other warranty, expressed or im- plied, shall govern equipment manufactured by Anetsberger Brothers, Inc. Under no circumstances shall Anetsberger Brothers, Inc., be liable for loss of profits or any direct or indirect cost, expenses, loss or damages arising out of...
Page 14
Anetsberger Brothers, Inc. 180 North Anets Drive • Northbrook, Illinois 60062 • 847-272-0770 • Fax 847-272-1943 Toll-free Customer & Warranty Service: 800/ 837-2638 Web Site: www.anetsberger.com Keep this Manual in a Convenient Location for Reference Form I-201; Rev. 3/02 Price $20.00 US...
Need help?
Do you have a question about the MG, SG, SGC and is the answer not in the manual?
Questions and answers