Related Manuals for NAPCO 2WAY-UNIVKF
Summary of Contents for NAPCO 2WAY-UNIVKF
- Page 1 2WAY-UNIVKF ® Bi-Directional LCD KeyFob Installation Instructions WI1024J 1/04 © NAPCO 2004 www.BevanSecurity.Com...
- Page 2 2WAY-UNIVKF - The 2-Way Universal LCD Keyfob that puts the power of a keypad in your pocket. NAPCO introduces the new 2WAY-UNIVKF, the security industry’s only universal bi- Easy LCD ICON Indicators directional Keyfob with LCD status display and integral mini sounder, supported by a revolutionary 2-way receiver.
-
Page 3: Table Of Contents
TABLE OF CONTENTS General Description Features • 3 Form C Relay Outputs The 2WAY-UNIVKF is a miniature Section Page remote control device which provides • Arm/Disarm wireless control of the security system GENERAL DESCRIPTION ..........3 • Panic and confirms system status visually and SYSTEM OVERVIEW .............4... -
Page 4: System Overview
SYSTEM OVERVIEW The 2WAY-UNIVKF is compatible with virtually any control This manual is divided into 3 sections which are marked on the outer border of each page - General Information (pages 2-7), panel, either through keypad bus operation or universal Bus Mode Operation (pages 8-16) and Universal Operation mode operation. -
Page 5: Wiring Diagram/ Configuration
WIRING DIAGRAM AND SYSTEM CONFIGURATION Enroll Mode Push Button Receiver LED System Configuration Jumpers 1 2 3 4 5 6 7 8 9 10 Panel Keypad Type Address • • Jumpers Jumpers page 8 page 8 9 10 13 14 15 Receiver LED Indications KeyFob Enroll Mode Rapid Flash... -
Page 6: Controls And Audible Indicators
ON/OFF automatically go out second garage in about 6 seconds. ∗ door. † Press ON/OFF and simultaneously to 6... Alarm ! activate lighting or other special application.† (repeats) † Bus Operation Only www.BevanSecurity.Com WI1024J 2WAY-UNIVKF Installation Instructions... -
Page 7: Visual Indicators
Visual LCD Indicators The 2WAY-UNIVKF uses a series of icons to convey the status of the system. Each time the STATUS button is pressed, or a command is issued, the appropriate icon(s) will display for about 6 seconds. For example, if ON/OFF is pressed to arm the system, the Armed icon will light in a few seconds to confirm that the command was successfully performed. -
Page 8: Bus Mode Wiring And Config
40 & 50 zone 99 must be programmed for 24 Hr Audible or 24 Hr Silent. Configuring the Receiver Address For the NAPCO Gemini and Vista 40 & 50 bus operation, the receiver must be addressed to match the address of the additional keypad enabled in programming above. -
Page 9: Bus Mode Enrolling Keyfobs
). All keyfobs will be deleted from the system. NAPCO "Classic" Keypads NAPCO "K Series" Keypads For NAPCO "K Series" Keypads, see pages 10 and 13. For Ademco Keypads, see pages 11 and 14 GEM-RP1CAe2, GEM-RP2ASe2, GEM-K1CA, GEM-K2AS,... - Page 10 ). All keyfobs will be deleted from the system. NAPCO "Classic" Keypads NAPCO "K Series" Keypads For NAPCO "Classic" Keypads, see pages 9 and 12. GEM-RP1CAe2, GEM-RP2ASe2, GEM-K1CA, GEM-K2AS, For Ademco Keypads, see pages 11 and 14...
- Page 11 1114 [AWAY] and then press [#] ). All keyfobs will be deleted from the system. For NAPCO "Classic" Keypads, see pages 9 and 12. For NAPCO "K Series" Keypads, see pages 10 and 13. Some Vista models will beep, others will not. Ignore all beeps.
-
Page 12: Bus Mode Enrolling User Codes
NAPCO "Classic" Keypads NAPCO "K Series" Keypads GEM-RP1CAe2, GEM- GEM-K1CA, GEM-K2AS, For NAPCO "K Series" Keypads, see pages 10 and 13. RP2ASe2, GEM-RP3DGTL GEM-K3DGTL, GEM-K4RF For Ademco Keypads, see pages 11 and 14 www.BevanSecurity.Com... - Page 13 NAPCO "Classic" Keypads NAPCO "K Series" Keypads GEM-RP1CAe2, GEM- GEM-K1CA, GEM-K2AS, For NAPCO "Classic" Keypads, see pages 9 and 12. RP2ASe2, GEM-RP3DGTL GEM-K3DGTL, GEM-K4RF For Ademco Keypads, see pages 11 and 14 www.BevanSecurity.Com...
- Page 14 Note: If these user codes are changed in control panel programming, the new user codes must be re-enrolled into the receiver. For NAPCO "Classic" Keypads, see pages 9 and 12. Some Vista models will beep, others will not. Ignore all beeps. For NAPCO "K Series" Keypads, see pages 10 and 13. www.BevanSecurity.Com WI1024J 2WAY-UNIVKF Installation Instructions...
-
Page 15: Bus Mode Garage Door & Special Apps
GARAGE DOOR CONTROL / SPECIAL APPLICATIONS When installed on the bus of a Gemini or Ademco control panel, receiver Relays 1 and 2 are available for other applications such as lighting or appliance control, while Relay 3 remains dedicated to the control of a garage door opener. •... -
Page 16: Bus Mode - Typical Applications
9 10 11 12 13 14 15 16 10 11 12 13 14 15 16 Door 2 Appliance Appliance GEMINI SYSTEM ARMED SYSTEM ARMED Appliance 01/01/00 12:00 AM 01/01/97 12:00AM GEM-X10 NEXT/YES PRIOR/NO AREA 7 8 9 0 COMPUTERIZED SECURITY SYSTEM www.BevanSecurity.Com WI1024J 2WAY-UNIVKF Installation Instructions... -
Page 17: Universal Mode Wiring Arm/Disarm/Panic
24 hour panic zone, which will process a 2 second violation as a panic alarm. The wiring instructions below series. include wiring schemes for control panels which support zone doubling, such as the NAPCO Express Wiring for Panic... -
Page 18: Universal Mode Enrolling Keyfobs
To remove a lost KeyFob from the system: Enter and then exit the Keyfob Enroll Mode. (Hold down Enroll Mode Push Button until Enroll Mode LED flashes, release and then hold down again to exit Enroll Mode). All keyfobs will be deleted from system. www.BevanSecurity.Com WI1024J 2WAY-UNIVKF Installation Instructions... -
Page 19: Universal Mode Arm / Alarm Sense
STEP 3 - WIRING FOR ARM & ALARM SENSE Wiring for Alarm Sense Wiring for Arm Sense In Universal Mode, the receiver requires an Alarm output from In Universal Mode, the receiver requires an Armed output from the control panel in order to pass the correct status to the the control panel in order to pass the system status to the KeyFob. -
Page 20: Universal Mode Wiring For Stay Mode
Interior Zones if the system is armed and the exit/entry door is not opened. Program the control panel for “Automatic Interior Bypass”, or for “Home Away with Delay” (for the NAPCO Express Series Stay mode). Each time the system is armed by a press of KeyFob button [ON/OFF], the system will arm in the AWAY mode, providing complete protection. -
Page 21: Universal Mode Garage Door Control
GARAGE DOOR CONTROL Wiring for Garage Door Control Changing the KeyFob battery In Universal operation, the 2WAY-UNIVKF may be used to Open battery compartment on back of Keyfob. control a garage door opener, or any other access control device which requires a momentary closure for activation. -
Page 22: Universal Mode - Typical Applications
For EITHER (3) Program Zone 5 for 24 Hour [05-5]. Fire OR Burg sense, no diodes are required. Garage Door Garage Door (4) Enable Home/Away with Delay [01-X] for all Control Control Interior zones www.BevanSecurity.Com WI1024J 2WAY-UNIVKF Installation Instructions... - Page 23 TYPICAL APPLICATIONS GARAGE DOOR CONTROL Typical Universal Mode applications with EOLR Control Panels using Arm and Alarm sense with Stay Mode and Garage Door control. DSC Power 832 BELL + 24 BELL - 23 PC5010 COM 18 AUX PWR + 17 Z8 16 KEYSWITCH ARM ZONE (1) COM 15...
-
Page 24: Warranty
EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE NAPCO is not an insurer of either the property or safety of the user's family or employees, SELLER'S OWN NEGLIGENCE OR FAULT.
Need help?
Do you have a question about the 2WAY-UNIVKF and is the answer not in the manual?
Questions and answers