Alarm Mode - Casio 2696 Operation Manual

Alarm Mode

Your watch comes with five alarms and an hourly time signal.
• Daily Alarms (AL 1 to AL 4)
The watch beeps for about 10 seconds when an alarm time is
reached.
• Snooze Alarm (SNZ)
With the snooze alarm, the watch beeps for 10 seconds when the
alarm time is reached, and up to seven times at five-minute
intervals thereafter (approximately 30 minutes total). Pressing any
button stops the beeper, but the alarm will sound again after five
minutes.
• Hourly Time Signal
The hourly time signal causes the watch to beep twice every hour
on the hour.
When you enter the Alarm Mode, the screen for the alarm that was
displayed when you last exited the mode appears first.
Timekeeping Mode Alarm Time
(Twice)
Alarm Number
5.
Use the D D D D D (+) and B B B (–) B B
buttons to change the
minute setting.
• Each press of the B (+) and
D (–) button changes the
minute setting in 30-minute (Forward)
increments.
• Holding down either button
changes the setting at high
speed.
6.
When the setting is the
way you want, press the
A A
A A button. A
• This exits the setting screen.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
Operation Guide 2696/2832 ( B )
❚ To select an alarm or the Hourly Time
Signal screen
Each press of the D button cycles through available screens in
the sequence shown below.
Alarm 1
Hourly Time Signal
Snooze Alarm
❚ To turn an alarm or the hourly time
(Back)
signal on and off
1.
In the Alarm Mode, use the
D button to display the D D D D
screen for the alarm you
want to turn on or off.
• The alarm number or snooze
alarm indicator (SNZ) appears
Alarm Number
at the bottom of the display to
indicate the current screen.
2.
Press the A A A A button to toggle the displayed alarm on or off. A
Alarm on indicator Snooze on indicator
Alarm
Hourly Time Signal on indicator
Hourly Time Signal
❚ To set an alarm time
Example: To set Alarm 2 for 3:30 p.m.
1.
In the Alarm Mode, use the
D D D D D button to scroll through
the alarm screens until the
one whose setting you want
to change is displayed.
Alarm 2
• The alarm number or snooze
alarm indicator (SNZ) appears
at the bottom of the display to
indicate the current screen.
2.
Hold down the A A A A button A
for about two seconds
until the hour digits start
Alarm 3
to flash on the display.
• This also causes the alarm on
indicator to appear and
automatically turns on the alarm.
A Button A A A A
• Enters/exits the setting mode.
B B B B B Button
Alarm 4
• Scrolls back through the options at the flashing (selected) setting.
C Button C C C C
• Moves the flashing between settings.
D D D D D Button
• Scrolls forward through the options at the flashing
(selected) setting.
❚ To stop the alarm beeper
Press any button.
• In the case of the snooze alarm the alarm will sound again in
about five minutes. "SNZ" flashes while the snooze alarm is active
(indicating that the alarm will sound again).
• The snooze alarm will be canceled automatically when any of the
following occurs while the SNZ indicator is flashing on the display.
• If you turn off the snooze alarm in the Alarm Mode.
• If you enter the Alarm Mode, display the snooze alarm screen,
and then display the setting screen.
• If you enter the Timekeeping Mode and then display the setting
screen.
❚ To test the alarm
In the Alarm Mode, hold down the D button to sound the alarm.
Snooze Alarm
3.
Use the D D D (+) and B D D B B B (–) B
buttons to change the
hour setting.
• Holding down either button
changes the setting at high
speed.
• When setting the hour, make
sure you specify AM (A) or
PM (P) correctly when using
Alarm Number
12-hour timekeeping, or that
you specify the correct 24-
hour time.
• The same 12-hour/24-hour
format you select for the
Alarm on indicator
Timekeeping Mode time is
also applied in the Alarm
Mode.
4.
Press the C C button to C C C
select the minute setting.
Hour
(Back)
(Forward)
Minute
7