Test Mode; General; Test Mode Setting; Test Mode Structure - Sony MZ-R55 Service Manual

4-1. GENERAL

This set pr ovides the Overall adjustment mode (Assy mode) that
allo ws CD and MO disk to be automaticall
test mode . In this Assy mode
CD and MO disk and then automatically perform adjustments for
them in sequence . If a fault is f ound, the system displa
tion. Also, the Ser vo mode allo ws eac h individual adjustment to be
automatically adjusted.

4-2. TEST MODE SETTING

See page 5.

4-3. TEST MODE STRUCTURE

Test mode

+ or VOLUME
VOLUME
or VOLUME
=
MODE key
EDIT/ENTER key

4-4. MANUAL MODE

(1) Servo Mode
• How to Transfer in the Servo Mode:
Mode No. Test Description
000 Servo mode
010 Offset correction value indication
011 VC offset correction
012 Focus bias correction
013 FE offset correction
014 ABCD offset correction
015 All servo ON
016 Temperature indication
020 Laser power adjustment
021 Laser CD/MO read adjustment
022 Laser MO write adjustment
023 Sled normal
024 Sled intermittent
025 Sled access
030 MO test adjustment
031 MO focus search adjustment
032 MO read FE balance adjustment
033 MO read ABCD level
034 MO write FE balance adjustment
035 MO write ABCD level
036 Laser MO read adjustment
037 MO focus gain
038 MO tracking gain
039 MO focus bias
040 Low reflection CD test adjustment
041 Low reflection CD focus search adjustment
042 Low reflection CD FE balance adjustment
043 Low reflection CD ABCD level
044 Laser low reflection CD read
045 Low reflection CD focus gain
046 Low reflection CD tracking gain
TEST MODE
y adjusted when in the
, the system discriminates between
ys its loca-
+ key
Manual Mode
+
key
Servo Mode
Audio Mode
Mechanism Mode
Power Mode
–
key

Overall Adjustment Mode

(Assy Mode)
Hybrid Mode (ALL Mode)
Key Check Mode
Check Write
® (08)
® (4C)
® (45)
® (65)
® (30)
® (0F)
® (07)
® (10)
® (18)
® (08)
® (30)
® (30)
® ® (06)
® (10)
® (06)
® (08)
® (30)
® (30)
SECTION 4
Mode No.
047 Low reflection CD focus bias
050 CD test adjustment
051 CD focus search adjustment
052 CD FE balance adjustment
053 CD ABCD level adjustment
054 Laser CD read
055 CD focus gain
056 CD tracking gain
057 CD focus bias
060 Recording test
061 32 cluster full recording
062 Recording shock
063 32 cluster full playback
Check : Mode to displa y err or rate and c luster .
Write : Mode to permit adjustment (Default v
theses).
1. Go into the test mode.
2. Press + or VOLUME + ke y to set the ser
Unit LCD display
SERVO
XX XX
3. Press the ke ys belo w to c hang e the mode No.
( : Increases the one place.
p : Sets the one place to 0.
This ke y brings the ten place to 0 if the one place is
0.
VOLUME + : Increases the ten place by 10 if the one place is 0.
Increases the adjustment v
is non-zero.
VOLUME – : Decreases the ten place by 10 if the one place is 0.
Decreases the adjustment v
non-zero.
• How to Adjust in Servo Mode:
1. When the ser vo mode is set to the appr
adjustment, the lo wer to w digits of the mode No.
stored in EEPR OM are displa yed and flashing.
SERVO
XX XX
– 12 –
Test Description Check
alue given in paren
vo mode .
Adjustment value
(the data can be changed/
written when flashing.)
Mode No.
(The lower two digits are indicated.
Three digits are indicated on the
remote controller LCD.)
alue if the one place
alue if the one place is
opriate mode f or eac h
Adjustment value (flashing)
Mode No. (lower two digits)
Write
® ® (00)
® (10)
® (15)
® (08)
® (30)
® (30)
® ® (00)
and the v alue