Tajfun Planina RCA 320-2 Operating Instructions Manual

Firewood processor

Advertisement

Tajfun Planina, proizvodnja strojev d.o.o.
Planina 41 a, 3225 Planina pri Sevnici, Slovenija
Tel.: + 3 8 6 ( 0 ) 3 7 4 6 4 4 2 0 , F ax .: + 3 8 6 ( 0 ) 3 5 7 9 1 0 1 6
E-m ail:
ex
port@tajfun.si, h ttp: / / www.tajfun.c om
O O P P E E R R A A T T I I N N G G I I N N S S T T R R U U C C T T I I O O N N S S
F I REW OOD P ROCES S OR
R R C C A A 3 3 2 2 0 0 - - 2 2
082.00.000
R R C C A A 3 3 2 2 0 0 - - 2 2 E E
083.00.000
880.04.096-GB
05/ 2006-GB
Please carefully read the operating instructions before using the machine!
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RCA 320-2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Tajfun Planina RCA 320-2

  • Page 1 Tajfun Planina, proizvodnja strojev d.o.o. Planina 41 a, 3225 Planina pri Sevnici, Slovenija Tel.: + 3 8 6 ( 0 ) 3 7 4 6 4 4 2 0 , F ax .: + 3 8 6 ( 0 ) 3 5 7 9 1 0 1 6 E-m ail: port@tajfun.si, h ttp: / / www.tajfun.c om...
  • Page 2: Table Of Contents

    5. 3 SPLITTING WEDGE REPLACEM ENT 5. 4 HYDRAULIC SYSTEM OIL CHANGE 5. 5 OIL FILTER M AINTENANCE 5. 6 LUBRICATION OF THE ANGLE REDUCTION GEAR ( RCA 320-2) 5. 7 CHAIN LUBRICATION 5. 8 TROUBLESHOOTING 5. 9 M AINTENANCE PLAN 5.
  • Page 3: General

    1 GENERAL De a r Cu s t o me r , By p u r c h a s i n g o u r f i r e wo o d p r o c e s s o r y o u o b t a i n e d t h e e q u i p me n t wh i c h wi l l p r o v i d e y o u wi t h g r e a t h e l p i n y o u r wo r k .
  • Page 4: Application

    1.2 APPLICATION Firewood processor (RCA 320-2, RCA 320-2 E) is a machine used for preparation of firewood. The processor can handle logs from 10 to 32 cm (4 – 12 1/ 2” ) in diameter, which can be cut to 25-50 cm (10 – 20” ) length and thereafter split.
  • Page 5 EP 11 ELECTRIC POWER UNIT EP 11 – Tajfun Motor Power: 11 kW Weight: 197 kg...
  • Page 6: Technical Data

    (95, 9" ) Req uir ed Tr ac tor Power (RCA 320-2) 30 k W (40 HP) El ec tr ic Dr iv e (RCA 320-2 E) El ec tr ic Motor U: 400V/ 50Hz P : 11 k W, n=2910 min , IP 55 Tr ac tor P.T.O.
  • Page 7: Safety Instructions

    • W hen troubleshooting, replacing the chain or any service procedure, always disengage P. T. O. shaft and shut down the tractor (RCA 320-2) or unplug the power cord from the electrical outlet (RCA 320-2 E) ! • Do not wear loose clothes! •...
  • Page 8: Discharge Conveyor Assem Bly

    RCA 320-2 E : Connect the RCA 3 20-2 E to the thee-phase electric power source: • Nominal voltage: 4 00 V / 50 Hz • Minimum Power Cable Siz e: 4 mm² • Plug: 3 2A-CCE 3 P+ N+ E 4 00V •...
  • Page 9: Ret Ract I On Of Di S Charge Convey Or

    Ensure the clearance “ t” between the nut and the hand winch handle axis. 3.2 TRACTOR PTO SHAFT DRIVE (RCA 320-2): • P.T.O. shaft (grooved shaft 13/8!" Z6 – DIN 96 11A) must comply with the req uired driving power of the machine (technical data).
  • Page 10: Starting Up

    Before starting the machine, make sure to loosen the conveyor belt, by moving the Discharge Conveyor from vertical to horizontal position using the hand winch (3-Figure:3). Otherwise damages to the belt can occur during the extension procedure! RCA 320-2 : • Examine the machine and equipment for faults and check the chain lubrication •...
  • Page 11: Transport Position Of The Machine

    4.1 NOISE Machine operator is exposed to the following noise levels, during the machine operation (measured near the ear of the machine operator): RCA 320-2 RCA 320-2 E I dl i ng mode: 87 dB (A) 88 dB (A) Oper at i on mode:...
  • Page 13: Sawing

    4.3 SAWING The barsaw is always operating. The sawbar movement is performed using the sawbar activation handle (H-Figure: 7), during which the sawed log must be held using the retaining handle (P- Figure: 7). When the sawing begins, the trapdoor (13-Figure:8) moves away automatically, so the log can fall freely into a splitting chute after the cut.
  • Page 14: Adjusting The Height Of The Splitting Wedge

    ¡ ¡ 4.4.1 ADJUSTING THE HEIGHT OF THE SPLITTING WEDGE By using a splitting wedge handle (L-Figure: 10), the splitting wedge can be gradually lifted or lowered depending on the diameter of the logs - so the logs are split in center. Splitting wedge adjustment can be performed most easily when the split- ting chute is empty or at the point when the splitting cylinders start to move.
  • Page 15: Start-Stop" Switch ( Rca 320 -2 E)

    4.4.3 “ START-STOP” SWITCH ( RCA 320 -2 E) Electrical system of the wood processor RCA 320-2 E includes, besides the main switch, also the “Start-Stop” switch (S-Figure: 1). The “Start-Stop” switch is used to turn ON/OFF the electric driving motor, which powers the cutting chain and whole hydraulic system.
  • Page 16: Maintenance And Repair

    Regular machine maintenance ensures reliable operation and long lifetime of the machine 5.1 CUTTING CHAIN REPLACEMENT Before replacing the chain, you must disconnect the machine drive (RCA 320-2) or unplug the power cord from the electrical outlet (RCA 320-2 E)! •...
  • Page 17: Chain Tensioning

    5.2 CUTTING CHAIN TENSIONING • Loosen both nuts (34-Figure: 15) on the fixing plate (35-Figure: 15) • Tighten the tensioning screw (33-Figure: 15) until the chain in tensioned correctly* • Tighten both nuts (34-Figure: 15) on the fixing plate (35-Figure: 15) *The cutting chain is tensioned correctly when it clings to the lower side of the sawbar when cold and can be still lifted on the upper side of the sawbar (approximately in the middle), three or four times the height of the driving teeth.
  • Page 18: Oil Filter Maintenance

    • Bad filter permeability is shown on the filter gauge – if the gauge indicator is in the red zone when oil is heated to operating temperature. Change the oil filter 5.6LUBRICATION OF THE ANGLE MULTIPLICATION GEAR (RCA 320-2) •...
  • Page 19: Troubleshooting

    Electric motor does not start or it often Damages to power cables or blown fuses Check the power cables, install the approp- shuts down (RCA 320-2 E) riate fuses Motor protection is shutting the motor Power cable size is not appropriate, the down.
  • Page 20: Maintenance Plan

    Multiplication gear oil change When changing the multiplication gear Drain the oil in the appropriate vessel (RCA 320-2) bearings. from the lowest plug and replace the plug. Fill the oil through the upper plug.
  • Page 21 WHAT? WHEN? HOW? Lubrication (Figure:19) Lubrication Point: a, b, c At least every 80 hours of operation Lithium Grease Lubrication Point: d At least every 80 hours of operation Lubricating Spray Lubrication Point: e At least every 8 hours of operation Lithium Grease Rope lubrication: f At least every 80 hours of operation Grease (apply with a brush)
  • Page 22: Cutting Chain Belt Replacement

    5.10 CUTTING CHAIN BELT REPLACEMENT • Disconnect the machine from the drive or unplug the power cord from the electrical outlet • Remove the drive protection (41 – Figure: 22), remove the housing cover (42 – Figure: 22), remove the drive cover (43 –...
  • Page 23: Belt Tensioning

    5.10.1 BELT TENSIONING The machine must be stopped, during the operation! Set the correct tension of the belt using the notch on the tension indicator. The notch must be aligned with the edge of the spring guide. Set the tension of the belt as follows: •...
  • Page 24: Indications Of Improper Use

    5.11 INDICATIONS OF IMPROPER USE Certain damages which occur before the end of the lifespan of exposed machine components may indicate overloading or inappropriate handling of the machine. Manufacturer’s warranty does not cover damages of this kind. • Torn or damaged in-feed or discharge conveyor belts •...
  • Page 25 Manufacturer: TAJFUN Planina, proizvodnja strojev d.o.o., Planina 41a, 3225 Planina pri Sevnici d ecl ares wi th ful l res p o ns i b i l i ty th at h erei nafter menti o ned p ro d uct:...
  • Page 26: Declaration Of Conformity

    Tel.: +386 (0)3 746 44 20, Fax.: +386 (0)3 5791 016 E-mail: export@tajfun.si, http://www.tajfun.com Declaration of Conformity Manufacturer: TAJFUN Planina, proizvodnja strojev d.o.o., Planina 41a, 3225 Planina pri Sevnici declares with full responsibility that hereinafter mentioned product: FIREWOOD PROCESSOR RCA 320-2 E...

Table of Contents