Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Cyber Console IC-1704
- Page 1 LCD KVM SWITCH IC-1704 / IC-1708 / IC-1716 USER MANUAL - 1 -...
-
Page 2: Lcd Monitor Specifications
LCD MONITOR SPECIFICATIONS Size 17 inch Screen Type Contrast 450:1 Brightness 300 cd/m View Angle 110¢X Resolution 1280x1024@75Hz Response Time 12 ms Display Color 16.7 M OPERATION Keypad Define Power key: Use this key to turn on or off the LCD monitor. Menu key: Use this key to open the OSD menu and enter to next menu or highlight a confirmed function. -
Page 3: Brief Introduction
BRIEF INTRODUCTION The KVM Switch allows you to control several sets of personal computers by a keyboard, a mouse and a monitor. In the meantime, you just need to connect the cable and turn on the power to control up to 256 sets of personal computers without installing any additional interface card or software. -
Page 4: Equipment Requirements
FEATURES ¡E The keyboard, mouse and 15” LCD monitor was built-in on KVM switch. ¡E Standalone machine controls up to 4/8/16 sets of PCs. ¡E Cascade controls 64/128/256 sets of PCs. ¡E Through OSD, you can use the hot key, mouse clicking and push button on front panel to switch PCs. -
Page 5: Specifications
SPECIFICATIONS IC-1704 IC-1708 IC-1716 3-in-1 Connecter HD-15 (Female) Monitor 17” TFT LCD Console Mouse Touch pad module Connector Keyboard Standard 104 key Port Selection Keys on Front Panel Port LEDs Power Built-in Video Resolution 1280x1024@75Hz Dimensions 600x450x48 mm Weight 13.3 Kg 13.35 Kg... - Page 6 • Simultaneously press Push Buttons 1 and 2 to directly enter the OSD Control Mode. • Simultaneously press Push Buttons 3 and 4 (IC-1704), Push Buttons 7 and 8 (IC-1708), Push Buttons 15 and 16 (IC-1716) to open “Console-Reconfirmed”, and the keyboard and mouse will be reconnected, and the EDID in the screen will be read again.
- Page 7 An blue light indicates that the KVM is operating. IC-1704 Rear VIEW IC-1708 Rear VIEW IC-1716 Rear VIEW 1. CPU Port Install the cable connected to a PC here. 2. Updata Port The port provides a firmware update function. 3. AC Power Jack The AC Power is applicable for 100~240VAC, 50Hz~60Hz 4.
-
Page 8: Installation
INSTALLATION ¡E Standalone 1. Make sure that the power switch at the rear panel of the KVM is OFF. Plug an end of the AC power cord into the KVM and the other end to an AC power supply. 2. Make sure to power off the PC and then install the 3-in-1 cable to each of the PC one by one. Note: If the ON-LINE LED (Green) of any port of a PC is on, then we recommend you to power off such PC (Turn off the power switch of the power supply of the PC or unplug the power cable of the PC) or wait till Step 5 to install that particular PC. - Page 9 power of the KVM is turned off), we recommend you to reinstall the whole system. Note: It is noteworthy that there are two levels available. ¡EExpansion 1¡BPCs It is not necessary to power down the KVM or other computer connected to the KVM system. You only need to power off the desired PC and connect the PC to the CPU port of the KVM in parallel by the 3-in-1 cable, and then power on the PC.
- Page 10 1. The Port Selection Switch functions only when connected to a PC. 2. If the Offline Skip of the OSD System Setting is Auto, then you cannot make any switch when pressing an offline Port Selection Switch. 3. For Auto Scan Mode, none of the Port Selection Switches functions. ¡E Key and Mouse Clicking Hot key and mouse clicking are applicable for switching a small section.
- Page 11 Switch Menu ¡E Master List 03-04:Mail Ser 4 LIST: MASTER NAME Admin ¡ò £K Press Enter Mail Group £R £K Peter ¡ò Web Group £R Data Group £R £K : Move Space: Edit Esc: Exit F1: Smart View Enter: Switching F4: Auto Scan F9: System Setting F5: Clear Name List...
- Page 12 (PC or KVM) connected to the CPU port. C# : It shows the channel number; the IC-1704 will display 01~04; the IC-1708 will display 01~08 and the IC-1716 will display 01~08; 09~16 (Since the screen cannot display all at a time, therefore you can use PgUp/PgDn to switch the pages).
-
Page 13: System Setting
System Setting Menu ¡E System Setting Channel Display Mode: Full Channel Display Time: 5 Sec Auto Scan Time: 5 Sec OSD Entry Hot Key: Number Lock Hot Key Switching: Mouse Clicking: Beeper Sound: Offline Skip: Manual OSD Language: English Security Level: None Console Lock Time: 5 Min... - Page 14 position. You can use the Up, Down, Left or Right keys on the keyboard or a mouse to move the OSD position. F8: Restore Default Setting; Restore the factory default settings. Please note that all name lists will be cleared and the system settings are set to the default settings as shown in the table above. Esc: Exit;...
-
Page 15: Troubleshooting
F/W version is the updated version. TROUBLESHOOTING Confirm whether or not the cable is good and connected properly Q1 : What should we do if the keyboard has no response? A1a: Reboot the PC. A1b: For Auto Scan Mode, press [Esc] to exit. Q2 : What should we do if the mouse has no respond? A2a:... - Page 16 - 16 -...
Need help?
Do you have a question about the IC-1704 and is the answer not in the manual?
Questions and answers