TABLE OF CONTENTS PAGE PAGE 1 Safety Precautions -----------------------------------------------3 1.1. General Guidelines ----------------------------------------3 1.2. Leakage Current Cold Check ---------------------------3 1.3. Leakage Current Hot Check (See Figure 1.) --------3 1.4. How to Discharge the E.Capacitor on the Frame Unit ---------------------------------------------------4 2 Warning --------------------------------------------------------------5 2.1.
1 Safety Precautions 1.3. Leakage Current Hot Check (See Figure 1.) 1.1. General Guidelines 1. Plug the AC cord directly into the AC outlet. Do not use 1. IMPORTANT SAFETY NOTICE an isolation transformer for this check. There are special components used in this equipment 2.
1.4. How to Discharge the E.Capacitor on the Frame Unit CAUTION: 1. Make sure to discharge the E.capacitor on the Frame Unit. 2. Be careful of the high voltage circuit on the Frame Unit when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and remove the necessary parts/unit. 2.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).
3 Service Navigation 3.1. Introduction This service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual. 3.2.
3.4. How to Define the Model Suffix (NTSC or PAL model) There are six kinds of DMC-LZ30, regardless of the colours. • a) DMC-LZ30P/PC • b) DMC-LZ30E • c) DMC-LZ30EE • d) DMC-LZ30GN • e) DMC-LZ30GK • f) DMC-LZ30PU/GC/GF/GW What is the difference is that the “Initial Setting” data which is stored in Flash-ROM mounted on MAIN P.C.B..
3.4.2. Initial Setting 1. Execute the Sales Area Setting Tool 2. Connect the DSC to PC by USB cable 1. Set the battery to the camera. 2. Turn off the power. 3. Press "Tele" + "Menu/Set" + "Playback" key at the same time. It starts in the state of "Engineer Mode" automatically. 4.
6 Service Fixture & Tools 6.1. Service Fixture and Tools The following Service Fixture and tools are used for checking and servicing this unit. REMARKS 1. ABOUT “LIGHT BOX”:...
7 Disassembly and Assembly Instructions 7.1. Disassembly Flow Chart This is a disassembling chart. When installing, perform this chart conversely. 7.2. PCB Location...
Page 19
7.3.7. Removal of the Lens Unit 7.3.8. Removal of the Front Case Unit NOTE: When Disassembling and Installing for the Lens Unit 1. Take care that the dust and dirt are not entered into the lens. In case of the dust is putted on the lens, blow off them by airbrush.
Page 20
7.3.9. Removal of the Speaker (Fig. D17) NOTE: (When Installing) Make sure to confirm the following points when installing: • The Screw is tightened enough. • Installing conditions are fine. (No distortion, no abnormal- space.) • No dust and/or dirt on Lens surfaces. •...
7.4. Lens Disassembly Procedure 7.4.3. Removal of the IR Filter Precaution: 1. Do not remove the CCD Unit when disassembling or reassembling the lens in order to maintain it clean. 2. Keep dust or dirt away from the Lens. 3. To remove dirt or dust from the Lens, blow with dry air. 4.
8 Measurements and Adjustments 8.1. Introduction When servicing this unit, make sure to perform the adjustments necessary based on the part(s) replaced. To perform the adjustment, it is necessary to use the “SPCA5330_v1020.exe” and “CK26200WriteQRCodeTool.exe” software. The Adjustment software “SPCA5330_v1020.exe” and “CK26200WriteQRCodeTool.exe” are available at “TSN Website”. 8.2.
Page 23
8.3.2. USB driver installation 1. Execute the Setup Launcher 2. Connect the DSC to PC by USB cable 1. Set the battery to the camera. 2. Turn off the power. 3. Press "Tele" + "Menu/Set" + "Playback" key at the same time. It starts in the state of "Engineer Mode" automatically. 4.
Page 24
8.3.3. MB/LCD Function Check 1. Setting the DSC 1. Set the battery to the camera. 2. Insert the SD card. 3. Turn off the power. 4. Press "Tele" + "Menu/Set" + "Playback" key at the same time. It starts in the state of "Engineer Mode" automatically. 5.
Page 25
8.3.5. OB Calibration 1. Setting the DSC 1. Set the battery to the camera. 2. Turn off the power. 3. Press "Tele" + "Menu/Set" + "Playback" key at the same time. It starts in the state of "Engineer Mode" automatically. 4.
Page 26
8.3.7. MeShut(LV13/LV14) Calibration 1. Setting the DSC 1. Set the battery to the camera. 2. Turn off the power. 3. Press "Tele" + "Menu/Set" + "Playback" key at the same time. It starts in the state of "Engineer Mode" automatically. 4.
Page 27
8.3.9. Light / S.S / Preview Calibration 1. Setting the DSC 1. Set the battery to the camera. 2. Turn off the power. 3. Press "Tele" + "Menu/Set" + "Playback" key at the same time. It starts in the state of "Engineer Mode" automatically. 4.
Page 28
8.3.11. Write Lens QR Code 1. Execute the Write QRCode Tool 2. Connect the DSC to PC by USB cable 1. Set the battery to the camera. 2. Turn off the power. 3. Press "Tele" + "Menu/Set" + "Playback" key at the same time. It starts in the state of "Engineer Mode" automatically. 4.
9 Maintenance 9.1. Cleaning Lens and LCD Panel Do not touch the surface of lens and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the its surface. Note: The Lens Cleaning KIT ;...