Advertisement
Quick Links
We are very proud of the design and quality
of our Power Juicer Express. This product has been manufactured
to the highest standards. Should you have any problem our friendly
customer service staff is here to help you
if you have a question.
We are available at:
1 1 - - 8 8 0 0 0 0 - - 5 5 2 2 6 6 - - 2 2 9 9 8 8 4 4
9:00
– 7:00
AM
PM
9:00
– 5:00
AM
© 2006 Tristar Products, Inc.
All rights reserved.
Tristar Products, Inc.
Wallingford, CT 06494
P P J J E E V V 2 2 0 0 6 6 2 2 1 1 0 0 6 6
EST Monday – Friday
EST Saturday
PM
Distributed By:
Advertisement
Related Manuals for Tristar Products PPJJEE VV22
Summary of Contents for Tristar Products PPJJEE VV22
- Page 1 We are very proud of the design and quality of our Power Juicer Express. This product has been manufactured to the highest standards. Should you have any problem our friendly customer service staff is here to help you 9:00 9:00 if you have a question.
- Page 2 OPERATING MANUAL...
- Page 3 Important Safety Information Helpful Hints Parts List Assembly Disassembly Cleaning Your Juicer Troubleshooting...
- Page 4 Money Order (NJ, PA, CT residents add 6% sales tax. NV & NY add applicable rate.) U.S. CURRENCY ONLY Please make checks payable to: POWER JUICER EXPRESS Mail Payment Today To: POWER JUICER EXPRESS 26 Barnes Industrial Rd. North, P.O. Box 3125, Dept. PE999, Wallingford, CT 06494 –...
- Page 5 Problem The motor does not run after being switched on. The motor is running with loud noise and shaking. The motor overheats causing the power to automatically shut off. Juice splashes from the rim of the receptacle. Machine is running, but no juice is coming out.
- Page 6 Power Juicer. • Do not unfasten the locking bar during operation. • To avoid risk of injury keep hands and utensils out of the juicer and away from its sharp blade during operation. • Use the pusher, not fingers or utensils, to propel the food into the juicer.
- Page 7 Once turned off it is quite normal for the juicer to spin for a minute or so due to the very fine precision balancing of this appliance. Wait until it is done spinning before disassembling.
- Page 8 Note: Juice spout will be in the locked position. STEP 2: To unlock, turn locking mechanism counter-clockwise, lining up notch with juicer spout hinge pivot arm. STEP 3: Lift up juice spout carefully from receptacle and remove to clean.
- Page 9 IMPORTANT: Before disassembling the unit make sure you turn the power OFF and unplug the machine from the electrical outlet. Pusher Chute STEP 1: Remove pusher from the chute. Lid with built-in Pulp Guard Pulp Collector STEP 3: Remove lid with built-in pulp guard by pulling up off of receptacle.
-
Page 10: Parts List
PARTS LIST MAIN UNIT (Fully Assembled) Pusher Pulp Collector Filter/Blade Removable Juice Spout Chute Receptacle Pulp Guard Safety MicroSwitch (Located on reverse side) Locking Bar Lid with Built-in Pulp Guard Base... - Page 11 The motor will not run if pulp collector is not properly assembled. Pulp Collector (Bottom) STEP 3: Place receptacle on the base, with juicer spout facing direction of locking bar. Settle receptacle into alignment. Assemble as shown Base Safety MicroSwitch...
- Page 12 STEP 4: Place filter/blade inside receptacle. Rotate the filter/blade allowing it to settle into alignment. Press down on rim of filter/blade firmly to secure. IMPORTANT: The unit will not start until filter/blade is secure and firmly in place. The motor will not start until the unit is properly assembled.