....................6 Front and Rear Panels ................8 Front Panel ......................8 Rear Panel ......................9 Powering up the MX1 ................10 The Menu System..................11 Controlling the Menu ................... 11 Getting Started ....................12 Configuring the Input TS ................14 Configuring QPSK1 or QPSK2 Input TS ............
Page 4
Enabling or Disabling MCD ..................37 Configuring MCD Slot 1 ..................37 Configuring the Descramblers Parameters ........... 38 Viewing the MX1 Status ................39 Viewing Alarms ..................39 Viewing Inputs ..................40 Viewing the QPSK1 or QPSK2 Inputs ..............40 Viewing the ASI 1 or ASI 2 Inputs .................
MX1. Where applicable, the additional options for the maximum configuration are indicated. This manual describes the operation of the MX1 through the LCD screen. Organization of this Manual Introduction. This chapter describes the hardware interfaces of the MX1 and the front and rear panels.
6 Introduction The MX1 Single MPEG-2 integrated receiver decoder is designed to reduce cost and satisfy video, audio, and data requirements of digital broadcast television, cable and satellite operations. The MX1 integrated receiver decoder is a fully interoperable decoder for digital media networks that complies fully with the DVB MPEG-2 standard.
Page 7
In remote mode, all decoder functions can be operated remotely from a PC under MS-WINDOWS through the IP interface. In addition to an RS232 or RS422 communication port, the MX1 can provide a General Purpose Interface (GPI) via a 9-pin D-type connector that allows dry contact alarms.
8 Front and Rear Panels The front panel provides the means to locally configure the MX1. The rear panel provides the electrical and communications interfaces. Front Panel The front panel contains a two-line LCD window and six control buttons, which are used to configure the MX1.
XLR Cable Wiring Figure 4: Rear Panel 9-Pin D-Type to XLR Connector If you connect a computer to MX1 Serial Port 1 or 2, you must configure the computer port to the settings listed in Table 2. Table 2: Serial Line Connection Requirements...
Computer Communication – 1 RS232, 1 RS422 Powering up the MX1 To power up the MX1, connect the power to the AC main and turn on the power switch. Figure 5 shows the power connector and switch on the rear panel of the MX1.
Figure 6: Menu System Controlling the Menu The MX1 is configured through the front panel buttons. The following six buttons are used to navigate the menu system and configure available parameters: ▼ scrolls downward through a menu. In edit mode, it is used to edit values.
{ } – data cannot be modified < > – data can be modified Getting Started After the MX1 powers up, the first two lines of the Main Menu appear. Figure 7illustrates the Main Menu screen. Figure 7: Main Menu Screen To view the rest of the menu, use the scroll buttons.
Page 13
Configuring the Output TS on page 31 CA System Configuring the CA System on page 35 Status Viewing the MX1 Status on page 39 Unit Config Viewing the Unit Configuration on page 44 Viewing and Configuring the Communication Comm Settings...
225.20.20.20 IS THE SOURCE STREAM UNIT IP ADDRESS. To edit the parameter: Press ► to move right one number or letter. Press ◄ to move left one number or letter. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
To discard your changes, press ESC. The LCD displays the Input TS Menu. Viewing the ASI 1 or ASI 2 Input TS The ASI Input Menu lists the input channels of the MX1. The parameters in the Input Menu cannot be modified. The numbers on the left side of the menu accompanying the inputs indicate whether the input is Input 1 or Input 2.
The Decoder Menu displays the service and service provider name. Through the Decoder Menu, you can configure the parameters for controlling the decoder. The Decoder Menu appears automatically on the MX1 screen after the system is idle for two minutes.
Configuring the Decoder Work Mode The Decoder Work Mode Menu allows you to define the service in a TS. The following is a list of possible work modes: The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Service Mode. You select the service by Service ID and name, and the MX1 uses the PIDs in the System Information (SI) table to identify the Elementary Streams (ES) that comprise the service. A PID is a unique identifier for the ES.
TS. To configure the PIDs Mode: 1. From the Main Menu, select Decoder > [Decoder Name] > Work Mode > PIDs Mode. The PIDs Mode Menu screen appears. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
The Decoder Video Menu allows you to view the video stream output within a TS. To configure the video output: 1. From the Main Menu, select Decoder > [Decoder Name] > Video. The Video Menu screen appears. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Test Signal <OFF > VBI functions Default Pict <SyncOff> Figure 29: Full Display Menu To edit the display parameters: Scroll through the menu and select the desired parameter. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Page 25
Functions. The VBI Functions Menu screen appears. Figure 30: VBI Functions Menu Screen To view the rest of the menu, use the scroll buttons. Figure 31 illustrates the full VBI Functions Menu. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Press ESC to discard your changes and return to the Decoder Submenu. Configuring the Decoder Vcxo Control The Vcxo control allows you to configure the synchronization between the transmission clock and the receiver clock. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
From the Main Menu, select Decoder > [Decoder Name] > Emb Audio. Press ► to move the cursor to the right side of the menu. You will get four options: ONE AUDIO The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
To edit the parameters: Scroll to the desired parameter. Press ► to move the cursor to the right side of the menu. Press ▼ and ▲ to toggle the parameter setting. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Page 29
Press ESC or ◄ to discard your change and return to the left side of the menu. To configure additional parameters, repeat steps 2 – 3. Press ► or ENTER to save changes and return to the Decoder Submenu. Press ESC to discard your changes and return to the Decoder Submenu. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
To access the Output Menu, select Output from the Main Menu. Figure illustrates the Output Menu screen. Figure 34: Output Menu Screen To view the rest of the menu, use the scroll buttons. Figure illustrates the full Output Menu. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Press ESC to discard your changes. The Decoder Submenu appears. Configuring the TS_OUT_2 CAM Parameters The TS_OUT_2 CAM parameters need to be configured if you select CAM 1 or CAM 2 as the input to Output 2. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
1. Select OUTPUT. 2. Press ► over IP OUT. 3. Use ▼ and ▲ buttons to change the input or to set it on off. 4. Press ENTER. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Page 33
Press ► to configure the low speed data (RS-232). The LSData Menu screen appears. Figure 38: LSData Menu Screen To view the rest of the menu, use the scroll buttons. Figure illustrates the full LSData Menu. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Page 34
The CA System Menu allows you to configure decryption in the decoder and CAM usage. To access the CA System Menu, select CA System from the Main Menu. Figure illustrates the CA System Menu screen. Common Interface The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual Descramblers St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
To configure the name, input, and status of the CAM 1 or CAM 2: 1. From the Main Menu, select CA System > Common Interface > CAM 1 or CAM 2. The CAM Menu screen appears. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Table 10: CAM Menu Parameter Values Parameter Possible Values QPSK1, ASI 1, ASI 2 Note: When the MX1 contains the maximum Input hardware configuration, options QPSK2, QPSK3, and QPSK4 may also appear. Cannot be edited. The field shows the name of the Name CAM manufacturer.
The MCD Menu allows you to add and remove the decrypted services of each CAM. Figure illustrates the MCD Menu screen. The MCD feature is only available to users of the MX1 3000 series. Figure 45: MCD Menu Screen To view the rest of the menu, use the scroll buttons. Figure 46 illustrates the full MCD menu.
Press ▼ and ▲ to change the parameter to ON or OFF. 4. Press ENTER to save your changes and return to the CA System Menu. Press ESC to discard your changes and return to the CA System Menu. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Figure 50: Status Menu Screen Viewing Alarms To view the MX1 alarms: From the Main Menu, select Alarms. A list of current alarms for the MX1 system appears. Figure 51: List of Alarms The Alarm list is a scrollable list that displays all of the current alarms for the system.
LNB FREQ 10650.00 Mhz Figure 54: Status QPSK Menu Screen To view the rest of the menu, use the scroll buttons. Figure illustrates the full Status QPSK Menu. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Page 41
10.600 GHz High Band 9.7500 GHz Low Band CBand 5.150 GHz Sym (Symbol) 1 - 45 MBaud Rate 1/2, 2/3, 3/4, 5/6, 7/8, Auto Polarity Horizontal, Vertical, None The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
22 KHz ON, OFF EB/N0 Signal: Noise ratio Bit Error Rate Note: If the MX1 displays a value of X.XXXX e-3 or higher (e.g., 2.0000 e-2) check your satellite connection. Gain Margin in Eb/N0. Gain Marg Note: A value less than 7 dB indicates a critical state.
Page 43
Port Number 00001 - 65535 UniCast. According to a specific broadcaster IP address MultiCast. The ranges between 224.0.0.1 to 239.255.255.255 2. Press ESC to return to the Main Menu. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
44 Viewing the Unit Configuration The Unit Configuration Menu displays the current configuration of the MX1. To access the Unit Configuration Menu, select Unit Config from the Main Menu. Figure 58 illustrates the Unit Configuration Menu screen. Figure 58: Unit Configuration Menu Screen To view the rest of the menu, use the scroll buttons.
45 Viewing and Configuring the Communication Settings The Communication Settings Menu displays the MX1 parameters for communicating with a network management system. It allows you to view the serial connection settings and configure the network connection parameters. To access the Communication Settings Menu, select Comm Settings from the Main Menu.
Figure 64: Full Serial Menu Screen For a description of the Serial Menu parameters, see Table 2. Press ESC to return to the Main Menu. Configuring Additional Setups The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
2. Select High Jitter and press ► to move the cursor to the right side of the LCD screen. 3. Press ▼ and ▲ to change the parameter value. The following are possible values: The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
4. Press ▼ and ▲ to change the parameter value. The following are possible values: LATIN CYRRILIC 5. Press ENTER to save your changes. Press ESC to discard your changes. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Press ► to move the cursor to the right side of the LCD screen. Press ▼ and ▲ to choose the parameter value you want the configuration to be saved on. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Page 50
Press ENTER to save the configuration. Figure 69 illustrates the Save Profile screen. Profile Number : <06> Stored: 06 (CNN) Figure 68: Save Profile Submenu 5. Press ESC to exit the configuration. The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...
Page 51
Pass Through Program Clock Reference physical layer Program Identification Picture in Picture Quad Quadrature monitoring SCPC Single Channel per Carrier Serial Digital Interface System Time Clock SYNCH Synchronization The MX1‐ Multi‐Channel MPEG 2 Single Decoder‐ Operation Manual St., Jerusalem 91450 Israel; Tel: +972-2-5714011 Fax: +972-2-5714033 info@adi-vt.com 7 Hamarpe...