Table of Contents
Advertisement
Quick Links
®
5" AIR SANDER/DRILL
Model 97187
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http//www.harborfreight.com
Copyright
2004 by Harbor Freight Tools
. All rights reserved. No portion of this manu-
©
®
al or any artwork contained therein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Central Pneumatic 97187
Summary of Contents for Central Pneumatic 97187
- Page 1 ® 5” AIR SANDER/DRILL Model 97187 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http//www.harborfreight.com Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this manu- © ®...
-
Page 2: Specifications
11. Remove adjusting keys and wrenches. Check that adjusting wrenches are removed from the tool or machine work surface before connecting it to its power source. 12. Avoid unintentional starting. Be sure the air compressor switch is in the Off position when SKU 97187 For technical questions, please call 1-800-444-3353. Page 2... - Page 3 (California health & Safety Code 25249.5, et seq.) Warning: The warnings, cautions, and instructions discussed in this instruction manual REV 01/06; REV 03/06 SKU 97187 For technical questions, please call 1-800-444-3353. Page 3...
- Page 4 Step 2: Open up the jaws of CHUCK (31) wide enough, insert screwdriver into chuck center and loose off CHUCK CENTER SCREW (32). Figure 1 — Installing the Holding Tool SKU 97187 For technical questions, please call 1-800-444-3353. Page 4...
- Page 5 CHUCK as far as possible. Step 4: By hand, turn the CHUCK to tighten the Jaws and make sure the jaws hold the drill bit well. Figure 3 — Opening the Drill Chuck SKU 97187 For technical questions, please call 1-800-444-3353. Page 5...
-
Page 6: Operation
Step 2: If possible, clamp the material in a vise to make sure the material does not move or begin to spin while drilling. REV 01/06; REV 03/06 SKU 97187 For technical questions, please call 1-800-444-3353. Page 6... - Page 7 Step 10: When you have drilled the hole, remove the drill bit from the hole while the Sander/ Drill is still spinning. This is to prevent the drill getting caught in the hole and causing damage. SKU 97187 For technical questions, please call 1-800-444-3353. Page 7...
-
Page 8: Maintenance
TRIGGER a few times to lubricate. CAUTION Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals in the tool. Figure 6 — Lubrication Points SKU 97187 For technical questions, please call 1-800-444-3353. Page 8... -
Page 9: Parts List
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 SKU 97187 For technical questions, please call 1-800-444-3353. - Page 10 SKU 97187 For technical questions, please call 1-800-444-3353. Page 10...
Need help?
Do you have a question about the 97187 and is the answer not in the manual?
Questions and answers