Related Manuals for IOGear GIC711SW6
Summary of Contents for IOGear GIC711SW6
- Page 1 Installation Guide Installation eSATA 1.5Gbps 1 external + 1 internal port Low profile PCI card GIC711SW6 PART NO. M0559...
-
Page 3: Table Of Contents
Table of Contents Introduction Features Package Contents Software Installation Federal Communications Commission (FCC) Statement CE Statement Limited Warranty Contact... -
Page 4: Introduction
Introduction The Low Profile Serial ATA 2 Channel PCI Host Adapter can support both Low profile PCI and standard size PCI. It provides a 32bit, 33/66 MHz PCI interface on the host side and dual Serial ATA ports on the device side to access SATA storage media such as: hard disk drives, ZIP drives, CD-ROMs, CD-RWs and DVD-ROMs. -
Page 5: Features
Features PCI Interface • Compliant with PCI Specification, revision 2.2 • Integrated PCI DMA engines • 32 bit, 33/66MHz fully compliant PCI host interface High Speed Serial ATA Interface • Dual high speed Serial ATA interface Channels, each supporting 1st generation Serial ATA data rates (1.5Gb/s) •... -
Page 6: Package Contents
Package Contents • Low Profile Serial ATA 2 Channel PCI Host Adapter • Low profile PCI bracket • SATA cable • Quick Start Guide • Driver CD... -
Page 7: Software Installation
Software Installation Windows XP Driver Installation 1. Before installation, copy all the files under directory [CD Drive Letter]:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_nt4.0\driver\ *.* to a blank floppy disk. 2. After the SATA PCI Host Adapter and attached drives are configured, follow Microsoft procedures to install Windows accordingly. - Page 8 Add Windows XP Driver to Original Boot Device 1. When the Found New Hardware Wizard starts, check the option to Install from a list or specific location (advanced), and click Next.
- Page 9 2. Insert the Driver CD. Point the wizard to the proper drive letter and click Browse. 3. Point the wizard to the following location: [CD Drive Letter]:\SATA Non-Raid_2Port\ Sil3x12\ Win98_me _2000_xp_nt4.0 \ Driver, click OK then Next. 4. Once the drivers have been installed click Finish to finalize the installation.
- Page 10 Verification of Proper Installation for Windows XP 1. Open Device Manager. 2. Double click SCSI and RAID Controllers, then double click Silicon Image Sil-3x12 SATALink Controller to display the driver properties. 3. If the message This device is working properly is displayed in the dialog box, then the driver has been correctly installed.
-
Page 11: Federal Communications Commission (Fcc) Statement
Federal Communications Commission (FCC) Statement Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. - Page 12 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1.
-
Page 13: Ce Statement
CE Statement CE Statement This device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law of member states relating to EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC and R&TTE Directive 99/5/EC. -
Page 14: Limited Warranty
IOGEAR shall not be responsible or liable for property damage, loss of use, interruption of business, lost profits, lost data or other consequential, punitive or special damages, however caused and however alleged. -
Page 15: Contact
Contact Toll Free: (866) 9-IOGEAR Phone: (949) 453-8782 23 Hubble Irvine, CA 92618 USA www.iogear.com support@iogear.com... - Page 16 About Us About Us IOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our high technology products. GREEN IOGEAR is an environmentally conscious company that emphasizes the importance of conserving natural resources. The use of our technology solutions helps reduce electronic waste.
Need help?
Do you have a question about the GIC711SW6 and is the answer not in the manual?
Questions and answers