COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CA-65 MODEL: EV700, CG771B ID LABEL: EV700A CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS SAFETY-RELATED COMPONENT WARNING! X-RADIATION There are special components used in this color monitor The only potential source of X-radiation is the picture tube. which are important for safety. These parts are marked However, when the high voltage circuitry is operating on the schematic diagram and the replacement parts properly there is no possibility of an X-radiation problem.
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW ID Label AC Power Socket Signal Cable Power (DPMS) Indicator Power ON/OFF Button Front Control Panel 2. Power (DPMS) Indicator 3. OSD Select/Adjustment 1. Power ON/OFF Button 1. Power ON/OFF Button 3. OSD Select/Adjustment This button is used to turn the monitor ON and OFF.
Page 6
On Screen Display (OSD) Control Icon Description To adjust an image size, position, and operating Mode Recall: To recall factory preset mode. parameters are quick and easy with the On Screen Display control system, using the OSD Select/Adjustment knob. A Advanced Option: There are four kinds of options.
CONTROL LOCATIONS CONTROL MAIN Ref. No. Control Function Ref. No. Control Function SW201 POWER SWITCH VR701 HIGHT-VOLTAGE ADJUSTMENT B + ADJUSTMENT VR201 OSD SELECT/ADJUSTMENT VR901 VR101 TCO ADJUSTMENT - 7 -...
DISASSEMBLY 3. TOTAL CHASSIS ASSEMBLY REMOVAL 1. TILT/SWIVEL REMOVAL 1) Disconnect P902 (Degaussing pin), P701, P601 1) Set the monitor face downward. (DY pin), and P501(Tilt pin). 2) Pressing the latch (a), carefully remove the 2) Remove two screws (a) from the Total Chassis Tilt/Swivel by pulling it upward.
Page 10
5. BOTTOM BRACKET REMOVAL 6. MAIN BOARD ASSEMBLY REMOVAL 1) Remove three screws (a). 1) Remove three screws (a). 2) Remove four screws (b). 2) Remove three screws (b). 3) Remove the Bottom Bracket. 3) Release two latches (c) from the Main Board Assembly.
Sense <OSD DISPLAY> Heater ( 6.3V ) CONTRAST Signal H-Sync Sig BRIGHTNESS Cable VIDEO VIDEO V-Sync Sig H-SIZE PRE-AMP MAIN AMP H-POSITION C DATA(SDA) (IC302) (IC303) V-SIZE C CLOCK(SCL) V-POSITION S-PCC 125V TRAP MICOM OSD IC 8V REG. CUT OFF DEGAUSS (IC401) (IC303)
DESCRIPTION OF BLOCK DIAGRAM 1. Line Filter & Associated Circuit. 5. Micom(Microprocessor) Circuit. This is used for suppressing noise of power input line The operating procedure of Micom(Microprocessor) and flowing into the monitor and/or some noise generated in its associated circuit is as follows: this monitor flowing out through the power input line.
Page 13
11. High Voltage Output & FBT(Flyback Transformer). 16. Image Rotation (Tilt) Circuit. The high voltage output circuit is used for generating This circuit corrects the tilt of the screen by supplying the pulse to the primary coil of the FBT(Flyback Transformer image rotation signal to the tilt coil which is attached near (T701)).
12) DRIVE ADJ command. 1) Display cross hatch pattern at Mode 1. 13) Set B-DRIVE to 155(170, LGE CDT) (decimal) at 2) Run alignment program for EV700 on the IBM DRIVE of the alignment program. compatible PC. - 14 -...
Page 15
14) Adjust R-DRIVE and G-DRIVE command to white 18) Adjust ABL to 41 ± 1FL of the luminance. ± 0.003 and y=0.311 ± 0.003 on the balance x=0.281 19) Exit from the program. White Balance Meter with PC arrow keys. 5.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK TROUBLE IN FUSE FUSE OK? (F901) CHECK C907 VOLTAGE? TROUBLE IN (AC120V: 170VDC, D901, D902, D903, D904 AC220V: 310VDC) CHECK IC901 PIN 3 TROUBLE IN WAVEFORM (SQUARE WAVE IC901, IC902 COMES OUT?) CHECK TROUBLE IN...
Page 17
2. NO CHARACTER NO CHARACTER CHECK TROUBLE IN IC302 PIN 7, 15, 18, P302 12V LINE, IC304 21(8V) ? TROUBLE IN CHECK PC SIGNAL, IC302 PIN 6, 8, 10 ? P301 SIGNAL CABLE CHECK TROUBLE IN IC302 PIN 16, 19, 22 ? IC302 CHECK TROUBLE IN...
Page 18
3. NO RASTER NO VIDEO (POWER INDICATOR ON) CHECK ORANGE DPM MODE POWER INDICATOR (NO H and/or V SYNC) GREEN or ORANGE? GREEN CHECK TROUBLE IN D712 ANODE D712 (-120V)? CHECK TROUBLE IN G1 VOLTAGE? Q801~Q806 (-10~20V) TROUBLE IN D926, Q925 (6.3V) - 18 -...
Page 19
4. NO HORIZONTAL DEFLECTION NO H-DEFLECTION (ONE VERTICAL LINE) CHECK TROUBLE IN Q706? Q706 CHECK B + VOLTAGE TROUBLE IN 160V LINE (160V)? CHECK TROUBLE IN T701(FBT) PIN 3 Q717, Q718, Q719, (31KHZ 70V, D707 69KHZ 140V) ? CHECK TROUBLE IN Q705 COLLECTOR Q705 WAVEFORM?
Page 20
5. TROUBLE IN H-LINEARITY UNBALANCED OF H-LIN. CHECK IC401 TROUBLE IN PIN 18, 19, 20? IC401 (MICOM) CHECK TROUBLE IN Q711~Q716? Q711 ~ Q716 CHECK TROUBLE IN L703? L703 Cs SIGNAL TABLE HORIZONTAL FREQUENCY(f TROUBLE IN 30K ~ 38.9K L720, R744 39K ~ 47.4K 47.5K ~ 61.9K 62K ~ 70K...
6. NO VERTICAL DEFLECTION NO V-DEFLECTION (ONE HORIZONTAL LINE) CHECK TROUBLE IN IC601 PIN 3 R603, Q601~Q603, (15V)? 15V LINE CHECK TROUBLE IN IC601 PIN 7 HIGH-VOLTAGE OUT (40V)? CIRCUIT, D713 CHECK TROUBLE IN IC701 PIN 12, 13? IC701 TROUBLE IN IC601, V-CIRCUIT - 21 -...
Page 22
7. TROUBLE IN OSD (ENTER BUTTON MUST BE PRESSED.) NO OSD CHECK TROUBLE IN IC301 B + ? 5V LINE DC 5V CHECK TROUBLE IN IC301 PIN 5, 10 IC601 PIN8 (V-FBP), WAVEFORM? T701 40V LINE Pin 10 Pin 5 CHECK TROUBLE IN IC311 PIN 12...
Page 23
8. TROUBLE IN DPM (NO OFF MODE.) OFF MODE FAILURE CHECK CHECK PC, IC401 (MICOM) INPUT H/V SYNC SIGNAL (PC IS NOT GOING INTO PIN 1, 42 (H/V INPUT) DPM OFF MODE) SIGNAL? NO H/V SYNC CHECK TROUBLE IN IC401 PIN 6 X401 WAVEFORM? 6MHz...
9. NO DEGAUSSING NO DEGAUSSING (DEGAUSS ON THE OSD MENU MUST BE PRESSED.) CHECK TROUBLE IN IC401 PIN 22 IC401 (MICOM) (0V)? CHECK Q921 COLLECTOR TROUBLE IN VOLTAGE? Q921 DC 5V (15V) CHECK TROUBLE IN P902, P903? P902, P903 CHECK TROUBLE IN RL901? RL901...
Page 25
10. NO TILT (NO ROTATION ) NO TILT (NO ROTATION) CHECK TROUBLE IN Q504 IC401 ( MI COM) WAVE FORM ? CHECK TROUBLE IN 15V LINE AND 15V LINE, 6.3V LINE 6.3V LINE ? CHECK TROUBLE IN Q503 EMITTER Q501~Q503 VOLTAGE ? TROUBLE IN P501, TILT COIL...
PCB ASS'Y, VIDEO BOARD, TOSHIBA CDT 3313T17033B CHASSIS ASS'Y, MAIN TOTAL, Northern Hemisphere 3313T17033F CHASSIS ASS'Y, MAIN TOTAL, Southern Hemisphere 3313T17033C CHASSIS ASS'Y, MAIN TOTAL, Northern TOSHIBA CDT * Remark ‘L’ are local sourcing parts in factory of the LG Electronics Inc. - 31 -...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS MODEL: EV700 DATE: 1999. 3. 16. AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION REMARK...
Need help?
Do you have a question about the EV700 and is the answer not in the manual?
Questions and answers