Advertisement
Quick Links
SAVE THESE INSTRUCTIONS
NOTE: Check ALL parts for shipping damage. If shipping
damage is noted, DO NOT use. Contact Carrier/Dealer for
further instruction.
PART
DESCRIPTION
NUMBER
SPARTAN - 65420
1076187
Cane Kit - Left
1076188
Cane Kit - Right
1076189
Brake Kit - Left (Before 3/7/00)
1076190
Brake Kit - Right (Before 3/7/00)
1096765
Brake Kit (After 3/8/00)
SPRINT - 65400
1076192
Cane Kit - Left
1076193
Cane Kit - Right
1076194
Brake Kit - Left (Before 3/7/00)
1076195
Brake Kit - Right (Before 3/7/00)
1096767
Brake Kit (After 3/8/00)
STINGRAY - 65500
1076182
Cane Kit
1076184
Brake Kit
STARGAZER - 65600
1076183
Cane Kit
1076184
Brake Kit
Note: Cane kits contain a push handle with hand grip, and
hand brake already attached.
SAFETY SUMMARY
The following recommendations are made for the safe
replacement of the Rollator Canes and Brakes:
GENERAL WARNINGS
DO NOT install this kit without first reading
and understanding this instruction sheet.
If you are unable to understand the
Warnings, Cautions and Instructions, con-
tact a healthcare professional, dealer or
technical personnel if applicable before
attempting to install this kit - otherwise,
injury or damage may occur.
A physical/occupational therapist should
assist in the placement and positioning of
the hand grips for maximum support and
correct brake activation. Be sure the
rollator is properly balanced BEFORE using.
Care should be taken to ensure that ALL
hand and height adjustments are secure,
and that casters and moving objects are
in good working order before using this
or any mobility aid.
SAFETY SUMMARY (CONTINUED)
INSTALLATION WARNINGS
SPRINT (65400) and SPARTAN (65420)
MODELS - The rollator height can ONLY be
adjusted where the push handle is textured
(FIGURE 4).
After installation and BEFORE use, ensure
that ALL attaching hardware is securely
tightened.
REPLACING SPRINT CANES AND
BRAKES (FIGURE 1)
1. Remove the EXISTING brake wire. Perform the fol-
lowing:
A. Loosen, but DO NOT remove the phillips screw
securing the brake wire to the brake wire clamp.
B. Remove the brake wire clamp and set aside.
C. Pull wire through the hole in the brake.
D. Remove the spring and set aside.
E. Pull wire through cable adjuster unit. If necessary,
loosen the cable adjuster unit locknut.
2. Pull brake cable UP to remove from side frame. If
necessary, cut ty-wrap.
3. Perform one (1) of the following:
INSTALLING CANE KIT - Remove EXISTING push
handle.
A. Rotate adjustment lever counterclockwise to
loosen. DO NOT remove.
B. Pull UP on the push handle to remove.
INSTALLING BRAKE KIT (BEFORE 3/7/00) - Re-
move EXISTING hand brake.
A. Remove the hex bolt, washer and locknut secur-
ing the hand brake to the push handle.
B. Remove the hand brake.
INSTALLING BRAKE KIT (AFTER 3/8/00) - Re-
move EXISTING hand brake.
A. Remove EXISTING hand grip from the push
handle and discard.
1
Advertisement
Related Manuals for Invacare Spartan 65420
Summary of Contents for Invacare Spartan 65420
-
Page 1: Safety Summary
Care should be taken to ensure that ALL hand and height adjustments are secure, and that casters and moving objects are in good working order before using this or any mobility aid. SAFETY SUMMARY (CONTINUED) INSTALLATION WARNINGS SPRINT (65400) and SPARTAN (65420) - Page 2 B. Remove the phillips screw securing the EXIST- ING hand brake to the push handle. C. Pull the EXISTING hand brake off of the push handle. NOTE: Remove clamps/hardware located at the end of the NEW brake wire before performing the following steps. 4.
- Page 3 REMOVING/INSTALLING BRAKE WIRE - STEPS 1 AND 6 DISASSEMBLED Cable Adjuster Unit Spring Brake Wire Clamp Phillips Screw REMOVING/INSTALLING BRAKE CABLE - STEPS 2 AND 5 Tie Wrap Side Frame Brake Cable REMOVING/INSTALLING HAND BRAKE - STEPS 3 AND 4 (AFTER 3/8/00) Mounting Hole Hand Brake Adjustment Nut...
- Page 4 REPLACING SPARTAN CANES AND BRAKES Preparing Spartan for Brake Replacement (FIGURE 2) 1. Perform one (1) of the following: INSTALLING BRAKE KIT (BEFORE 3/7/00) - Re- move EXISTING hand brake. A. Remove the hex bolt, washer and locknut secur- ing the hand brake to the push handle. B.
- Page 5 Removing/Installing The Spartan Brake Pad Only (FIGURE 3) 1. Remove the tire. Perform the following as shown in DETAIL “A” of FIGURE 3: A. Remove the cap covers from both sides of the tire. B. Remove the screw and locknut that secure the tire to the rollator.
- Page 6 REMOVING/ INSTALLING THE PLUNGER ASSEMBLY - STEPS 2 AND 9 Rear Frame Screwdriver Plunger Assembly DISASSEMBLING/ASSEMBLING THE PLUNGER ASSEMBLY - STEPS 4 AND 7 Brake Plunger Slot Wire Spring FIGURE 4 - REPLACING SPARTAN CANES AND BRAKES - REPLACING SPARTAN BRAKES Assembling Spartan For Use (FIGURE 5) NOTE: The Spartan rollator should only be assembled AFTER replacing spartan brakes.
- Page 7 B. Remove the hand brake. C. Turn the adjustment lever COUNTERCLOCK- WISE. D. Insert push handles into side frames with the hand grip facing the back of the rollator. 3. Perform one (1) of the following: INSTALLING BRAKE KIT (BEFORE 3/7/00) - Install NEW hand brake.
- Page 8 ADJUSTING SPRINT AND SPARTAN PUSH HANDLES (FIGURE 6) NOTE: For the most comfortable position, make sure the adjustment is performed while wearing the most frequently worn shoes. NOTE: COUNTERCLOCKWISE/CLOCKWISE di- rections are determined by standing behind the rollator (users position). 1.
- Page 9 Adjusting Cable Adjuster Unit - Wheel Assembly - MODEL 65400 ONLY (FIGURE 8) NOTE: Adjusting the cable adjuster unit will increase/ decrease the cable brake pressure on the wheels. NOTE: COUNTERCLOCKWISE/CLOCKWISE di- rections are determined by standing behind the rollator (users position). 1.
- Page 10 REPLACING STINGRAY AND STARGAZER BRAKES (FIGURE 10) NOTE: COUNTERCLOCKWISE/CLOCKWISE direc- tions are determined by standing beside the rollator. 1. Remove the EXISTING brake wire. Perform the fol- lowing: A. Loosen the hex screw securing the EXISTING brake wire to the brake. B.
-
Page 11: Replacing Brake Cable
ADJUSTING STINGRAY AND STARGAZER HAND BRAKES (FIGURE 10) Adjusting Hand Brake NOTE: COUNTERCLOCKWISE/CLOCKWISE direc- tions are determined by standing behind the rollator (us- ers position). 1. Loosen the hand brake adjustment nut by turning CLOCKWISE. 2. Perform one (1) of the following: A. - Page 12 Removing/Installing The Stingray Brake Pad (FIGURE 11) 1. Remove the tire. Perform the following as shown in DETAIL “A” of FIGURE 11: A. Remove the cap covers from both sides of the tire. B. Remove the screw and locknut that secure the tire to the rollator forks.