Advertisement
Table of Contents
- 1 Table of Contents
- 2 Important Safety Precautions
- 3 Introduction / What's in the Box
- 4 Front & Rear Panels
- 5 Remote Control
- 6 Setting up Your Speakers
- 7 USB Charging Operation
- 8 Use with Ipods, Iphones, Ipads
- 9 Use with MP3 Players
- 10 Use with Ipod / Iphone Docks
- 11 Use with Auxiliary Sources
- 12 Use with PC or Laptop
- 13 Use with Optical Devices
- 14 Connecting a Sub-Woofer
- 15 Specifications
- 16 Other Kanto Products / Warranty
- Download this manual
Advertisement
Table of Contents
Related Manuals for Kanto Yumi
Summary of Contents for Kanto Yumi
- Page 1 English User Manual YUMI Powered Speaker System YUMI POWERED SPEAKER SYSTEM ™ Supporting your digital lifestyle...
-
Page 2: Table Of Contents
Specifications . . . . . . . . . . . . . . . . 15 Use with iPods, iPhones, iPads . . . . . . 8 Other Kanto Products / Warranty . . . . . . 16 Important Safety Precautions... -
Page 3: Introduction / What's In The Box
Introduction Thank you for choosing the YUMI Powered Speaker System, designed by Kanto in Canada . YUMI outputs 30W RMS (60W peak) per side into 6 Ohm speakers, for remarkably bold and clean sound . Excellent sensitivity and frequency response specs provide deep thumping lows and clear, scintillating highs . -
Page 4: Front & Rear Panels
OPT1 12 Right Channel Output Terminals (+ and −) for Passive Speaker OPT2 Connection 13 USB Charge Ports YUMI (2 x 5V 500mA) 14 Voltage Select Switch (115V 60Hz / 230V 50 Hz) 15 ON/OFF Switch 16 AC Input Connection... -
Page 5: Remote Control
Remote Control Install two supplied AAA batteries in the back of your YUMI remote . Remote Control functions are listed below . Mute USB Charge Mode - see page 7 Standby - press to enter Standby Mode BLUETOOTH CONTROLS Previous Track... -
Page 6: Setting Up Your Speakers
Follow the instructions on the ensuing pages to connect your devices to YUMI . The examples in the following pages are not meant to be exhaustive - just examples . Connect the AC power cord from YUMI’s active speaker to your wall outlet . Turn YUMI’s ON/ OFF switch to the ON position . -
Page 7: Usb Charging Operation
. (Note that if the Bluetooth LED stays solid, YUMI has likely found a previously paired device in range.) 2 . Enable your Bluetooth device to search for a new device . Select ‘YUMI by Kanto’ from the list of Bluetooth devices . If prompted for a pairing code enter ‘1234’ . -
Page 8: Use With Ipods, Iphones, Ipads
. Press the 3 .5 button on the remote (or cycle through inputs by pressing the volume knob on the front of YUMI) and you will be able to listen to the device on YUMI . For wireless playback, follow the Bluetooth instructions on page 7 to pair your iPod or iPhone with YUMI . -
Page 9: Use With Mp3 Players
You can connect any MP3 or other auxiliary device that has a 3 .5mm stereo mini-jack output to YUMI’s 3 .5 input . Plug one 3 .5mm stereo plug into your device, and the other plug into YUMI’s 3 .5 input . -
Page 10: Use With Ipod / Iphone Docks
3 .5 button on the remote (or cycle through inputs by pressing the volume knob on the front of YUMI) and you will be able to listen to the device on YUMI . -
Page 11: Use With Auxiliary Sources
YUMI . Press the RCA button on the remote (or cycle through inputs by pressing the volume knob on the front of YUMI) and you will be able to listen to the device on YUMI . OPT1... -
Page 12: Use With Pc Or Laptop
(This applies to all devices with a 3.5mm stereo mini-jack connection) Your PC or laptop has a headphone jack that can be connected to your YUMI . This can be done in one of two ways . Connect using a 3 .5mm stereo mini-jack cable (as shown on page 9), or connect to the RCA L/R inputs using a ‘Y’... -
Page 13: Use With Optical Devices
2 channel output, or YUMI will not recognize the input. If you cannot set the device to 2 channel audio, most such devices will also have either a mini-jack or RCA output connections as well, so these can be used instead.) -
Page 14: Connecting A Sub-Woofer
Connecting a Sub-Woofer YUMI is equipped with an RCA connector to provide output signal to a powered sub-woofer . Simply connect an RCA cable from the SUB OUT connection on YUMI to the AUDIO INPUT on your sub-woofer . Kanto offers the YARO SUB, a 200 Watt powered sub-woofer with crossover and volume controls . -
Page 15: Specifications
NOTICE: iPod, iPhone and iPad are trademarks of Apple Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. ® and any use of such marks by Kanto Distribution Inc. is under license. ™ Supporting your digital lifestyle... -
Page 16: Other Kanto Products / Warranty
If equipment fails because of such defects and Kanto or an authorized dealer is notified within 24 months from the date of shipment with proof of original invoice . Kanto will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications .