Summary of Contents for Talbsys Basic Vortex
- Page 1 InstructIon Manual InstructIon Manual Basic Vortex Mixer standard Vortex Mixer advanced Vortex Mixer Pulsing Vortex Mixer...
-
Page 2: Package Contents
able of ontents Package Contents ....Warranty ....Installation ....Maintenance &... -
Page 3: Installation
nstallation nvironmental onDitions Upon receiving the Talboys’ Vortex Mixer, check to ensure that no damage has Operating Conditions: Indoor use only. occurred during shipment. It is important that any damage that occurred in transport Temperature: 4 to 40°C (39.2 to 104°F) is detected at the time of unpacking. -
Page 4: Safety Instructions
& r afety nstructions tanDarDs egulations Please read the entire instruction manual before operating the Vortex Mixer. Henry Troemner LLC hereby declares under it’s sole responsibility that the construction of this product conforms in accordance with the following standards: WarNiNg! DO NOt use the Vortex Mixer in a hazardous atmosphere or with hazardous materials for which the unit was not designed. - Page 5 & P ixeD PeeD ortexer ixer Pecifications igital ulsing ortexer ixer Pecifications Overall dimensions (L x W x H): 8 x 5 x 5.25” Overall dimensions (L x W x H): 8 x 5 x 5.25” (20.3 x 12.7 x 13.3cm) (20.3 x 12.7 x 13.3cm) Electrical (50/60 Hz): 120V:...
- Page 6 & P igital ulsing ortex ixer ontrol anel The front panel of the Digital/Pulsing Vortex Mixer contains all the switches, controls and displays needed to operate the unit. a. 3-way rocker switch: Auto/standby/on rocker switch starts/stops the vortexing function. B. time display: Displays accumulated time (continuous mode) or how much time is remaining (timed mode).
- Page 7 ortex ixer ntroDuction nalog ortex ixer Perating nstructions Your Vortex Mixer is ready for most one-handed applications. The Vortex Mixer 1. Make sure the 3-way rocker switch is in the center, off position. Plug the power operates by mixing tubes just prior to testing. cord into a properly grounded outlet.
- Page 8 & P igital ulsing ortex ixer Perating nstructions Pulse operation: (for Pulsing Vortex Mixer only) 1. Make sure the 3-way rocker switch is in the center, standby position. Plug the power cord into a properly grounded outlet. The unit is now on and in a standby • Set the time if desired.
- Page 9 ccessory nstallation nstructions installing the cup head, 3” head or other head attachments: installing Vessel Harness: 1. Move the 3-way rocker switch to the center, off/standby position. For the Fixed 1. Install Insert Retainer without foam tube holder onto Vortex Mixer. Speed Vortex Mixer disconnect the power cord from the wall outlet.
- Page 10 ccessory nstallation nstructions installing Single tube Holder: 1. Move the 3-way rocker switch to the center, off/standby position. Single Tube Holder should NOt be used on the Fixed Speed Vortex Mixer. 2. Remove cup head, or any other accessory from the Vortex Mixer. 3.
-
Page 11: Troubleshooting
roublesHooting Problem Cause Solution Mechanical obstruction Remove obstruction and press down on cup head several times to confirm no obstruction exists. If Unit will not run or Motor obstruction problem persists, please contact your Talboys representative for repair. Sensor fan misaligned Unit is excessively noisy This error cannot be fixed by the end user. Please contact your Talboys representative for repair. - Page 12 ccessories Micro-tube Holder - Mixes (48) 0.25 to 2mL microtubes. Flat Foam insert - Ideal for custom applications. Can Requires Insert Retainer. be cut or drilled to fit your specifications. Requires Insert Description Part Number Retainer. Micro-Tube Holder (2 pk) 945638 Description Part Number...
- Page 13 ’ ccessories cont tube Holder Kit 0.5mL Micro-tube Holder Includes: (1) 9-13mm Tube Holder, (1) 14-19mm Tube Mixes (24) 0.5mL micro-tubes. For use with Single Holder, (1) 20-25mm Tube Holder, 1 Flat Foam Insert, 2 Tube Holder. Vessel Harness, and 1 Insert Retainer Part Number 945655 Part Number...
- Page 14 Manufactured by: 201 Wolf Drive • PO Box 87 • Thorofare, NJ 08086 • Phone: 1-888-TALBOYS • Fax: 856-686-1601 E-mail: troemner@troemner.com • www.troemner.com 715027-00 (REV 6 - 8/14)