Summary of Contents for Optiva VODN46xxIR
-
Page 1: User Manual
VODN46xxIR IR Speed Dome User Manual V1.0.0 Distributor: VOLTA Ltd Jutrzenki Street 94; 02-230 Warsaw www.volta.com.pl... - Page 2 IR Speed Dome User Manual Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual is applicable to the IR Speed Dome. This manual may contain several technically inaccurate places or printing errors, and the content is subject to change without notice.
-
Page 3: Regulatory Information
IR Speed Dome User Manual Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 4: Safety Warnings And Cautions
IR Speed Dome User Manual Safety Warnings and Cautions Please pay attention to the following warnings and cautions: Hazardous Voltage may be present: Special measures and precautions must be taken when using this device. Some potentials (voltages) on the device may present a hazard to the user. This device should only be used by Employees from our company with knowledge and training in working with these types of devices that contain live circuits. - Page 5 IR Speed Dome User Manual Thermal and Mechanical Injury: Some components such as heat sinks, power regulators, and processors may be hot; care should be taken to avoid contact with these components. Electro Magnetic Interference: This equipment has not been tested for compliance with emissions limits of FCC and similar international regulations.
-
Page 6: Safety Instruction
IR Speed Dome User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. - Page 7 IR Speed Dome User Manual otherwise (which is not a malfunction however), and affecting the endurance of CCD at the same time. 6. Please use the provided glove when open up the dome cover, avoid direct contact with the dome cover, because the acidic sweat of the fingers may erode the surface coating of the dome cover.
-
Page 8: Table Of Contents
IR Speed Dome User Manual Contents Chapter 1 Introduction ............................1 Production Features ............................. 1 Chapter 2 Getting Started ............................. 2 Power on Self-test ..............................2 System-defined Presets ............................3 On Screen Display ..............................3 Chapter 3 Menu Operation ........................... 4 Main Menu ................................ -
Page 9: Chapter 1 Introduction
IR Speed Dome User Manual Chapter 1 Introduction 1.1 Production Features IR speed dome adopts a high-performance integrated sensor with the auto-focus and auto-white balance function. With a built-in pan/tilt unit, the IR speed dome features in highly sensitive response and reliable performance. The outstanding features are shown as below: Adopt 1/4"... -
Page 10: Chapter 2 Getting Started
IR Speed Dome User Manual Chapter 2 Getting Started Before you start: You can operate the speed dome using a control device. The control devices include the control keyboards, DVRs, DVSs, etc. In this and the following chapters, operation of the speed dome by the IE browser of a DVR is taken as an example. -
Page 11: System-Defined Presets
IR Speed Dome User Manual 2.2 System-defined Presets Purpose: The section lists the system-defined presets with special functions. These presets cannot be edited but only be called by a control device, e.g., a DVR. To call the system-defined presets remotely, you can choose the preset number from the drop-down list in the PTZ control panel of the control device through a web browser. -
Page 12: Chapter 3 Menu Operation
IR Speed Dome User Manual Chapter 3 Menu Operation Notes: 1. The operation interface of the different speed domes may differ. Please refer to the actual operation interface. 2. You can click the left and right direction buttons in the PTZ control panel via the IE browser of the DVR to enter the next page and return to the previous page of the submenu if more than one page is available. -
Page 13: Configuring The System Parameters
IR Speed Dome User Manual Figure 3-2 Dome Setup 3.2.1 Configuring the System Parameters Purpose: You can check and also edit the system information of the software address, baudrate, system time, etc. on the system information settings menu. Enter the system information settings menu: MAIN MENUS >... - Page 14 IR Speed Dome User Manual the control device (e.g. the DVR). 2. After you enable/disable the soft address, the speed dome will reboot automatically to activate the settings. Soft baudrate settings If the SOFT BAUD is set as ON, the soft baudrate is the valid baudrate for the speed dome, with 2400, 4800, and 9600 are selectable.
-
Page 15: Configuring The Camera Settings
IR Speed Dome User Manual menus, you can set them to “OFF”. Figure 3-5 Display Setup 3.2.2 Configuring the Camera Settings Note: The menu operation interface of the different model of speed dome may differ. Please refer to the actual operation interface. You can configure the Focus, Shutter, White Balance and Noise Reduce, etc. - Page 16 IR Speed Dome User Manual Zoom limit is a user-defined limitation of the zoom amount (Zoom amount=optical zoom× digital zoom). Take DS-2AF1-762 as an example, if you set the zoom limit as 20, the optical zoom function will be performed, and if you set the zoom limit to 40, 80, 160, or 320, the digital zoom function will be enabled then.
-
Page 17: Configuring The Ptz Parameters
IR Speed Dome User Manual The value of gain indicates the amplification degree of the original image signal. You can set the value from 0 to 15. Exposure Compensation Function: You can set the EXPOSURE COMP value from 0 to 14. The value change can affect the exposure effect, and the default value is 7. - Page 18 IR Speed Dome User Manual Figure 3-7 PTZ Configuration Descriptions of PTZ parameter configuration: Auto-Flip In manual tracking mode, when a target object goes directly beneath the speed dome, it automatically rotates (flips) 90 degrees horizontally to track the object, if there is no further command received, it rotates 180 degrees horizontally, and then move upward straightly.
-
Page 19: Configuring The Ir Parameter Setup
IR Speed Dome User Manual The manual movement speed can be set as HIGH, MID or LOW. Limit Stops If you set the limit stops to OFF, the movement of the speed dome will not be affected even if you setup the limits. Limit Setup Steps: 1. -
Page 20: Configuring The Patrol
IR Speed Dome User Manual Far LED Current refers to the strength of the far IR LED. Note: The near LED current function is only supported by a certain camera model series. LED Control Auto, Close, All On, Far On, Near On are selectable according to the different environment demands. - Page 21 IR Speed Dome User Manual 3. Patrol Setup. Steps: (1) Move the cursor to PATROL SETUP and click IRIS+ to enter the edit mode. Figure 3-10 Edit the Patrol (2) Click up/down direction buttons to position the preset to be edited. (3) Click left/right direction buttons to position the cursor to PRESET, DWELL TIME and SPEED of a preset.
-
Page 22: Configuring The Pattern
IR Speed Dome User Manual 3.2.6 Configuring the Pattern Purpose: A pattern is a memorized, repeatable series of panning, tilting, zooming and preset movements that can be recalled by a command or automatically performed by a configured function (park, time task, and power-up). -
Page 23: Configuring The Time Tasks
IR Speed Dome User Manual (2) Click the PTZ control buttons and direction buttons to pan, tilt, call the presets or zoom in/out the speed dome to draw a movement path. The speed dome can automatically memorize the path you operated as a pattern. (3) Click IRIS+ again to save the pattern and exit edit mode. - Page 24 IR Speed Dome User Manual (1) Move the cursor to TASK STATE and click IRIS+ to enter the edit mode. (2) Click the up and down direction buttons to set the task status to ON. (3) Click IRIS+ again to confirm and exit edit mode of this column. If you set the task state as “OFF”, it won’t take the task even if you set the task Note: memory.
-
Page 25: Configuring The Privacy Mask
IR Speed Dome User Manual the last line refers to the task No.8. 7. Task Clean. Move the cursor to TASK CLEAN and click IRIS+ to delete the time and action of the current task. 3.2.8 Configuring the Privacy Mask Purpose: Privacy mask enables you to cover certain areas on the live video to prevent certain spots in the surveillance area from being live viewed and recorded. -
Page 26: Restoring The Default Settings
IR Speed Dome User Manual ADJUST BLANK POS FOCUS SHIFT STATUS SAVE: OPEN QUIT: CLOSE Figure 3-17 Set the Privacy Mask (2) You can see ADJUST BLANK POS message on the screen. Click the direction buttons to adjust the position of the privacy mask to the designed scene. (3) Click FOCUS + button on the PTZ control panel, and you will see ADJUST BLANK SIZE message on the screen. -
Page 27: Restoring The Camera Settings
IR Speed Dome User Manual D&N Mode AE mode Auto White balance Auto Proportional pan Park time 5 seconds Park action None Scan speed 23 °/second Limit stops Default Dome Settings Table 3-2 3.4 Restoring the Camera Settings Enter default camera settings menu: MAIN MENUS >... -
Page 28: Appendix
IR Speed Dome User Manual Appendix Appendix 1 Lightning & Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000W, like instantaneous lighting, surging, etc. According to the actual situation outdoors, necessary protection measures must be taken to secure the electrical safety. -
Page 29: Appendix 2 Rs485 Bus Connection
IR Speed Dome User Manual Lightning & Surge Protection Figure A- 1 Appendix 2 RS485 Bus Connection General Property of RS485 Bus According to RS485 industry bus standard, RS485 is a half-duplex communication bus which has 120Ω characteristic impendence, the maximum load ability is 32 payloads (including controller device and controlled device). - Page 30 IR Speed Dome User Manual RS485 Connection 1 Figure A-2 RS485 Connection 2 Figure A-3 Problems in the Practical Application Normally, users adopt star-shape connection method in construction, under this situation, the terminal resistors must be connected between two farthest devices (as Figure A- 4, 1# and 15#), but this connection method is not satisfy the requirement of the RS485 industry standard so that it will lead to some problems such as signal reflection, anti-jamming ability decline when the devices are faraway.
- Page 31 IR Speed Dome User Manual RS485 Distributor Figure A-5 FAQ of RS485 Bus...
-
Page 32: Appendix 3 24Vac Wire Gauge & Transmission Distance
IR Speed Dome User Manual Appendix 3 24VAC Wire Gauge & Transmission Distance The following table has described the recommended maximum distance adopted for the certain wire gauge when the 24VAC voltage loss rate is less than 10%. For the AC driven device, the maximum voltage loss rate allowable is 10%. -
Page 33: Appendix 4 Table Of Wire Gauge Standards
IR Speed Dome User Manual Appendix 4 Table of Wire Gauge Standards Cross-sectional Area Bare Wire Gauge Americ an Wire Gage (Brit ish)St andard Wire G auge Bare Wire (mm) -
Page 34: Glossary
IR Speed Dome User Manual Glossary Note: The glossary gives brief explanations to the or the basic function of the basic operation principle speed dome. However, it doesn’t mean the listed functions are all supported by this series of speed dome. - Page 35 IR Speed Dome User Manual Title text is the label used to identify the camera viewed on the monitor. Up to 15 characters can be used for a title DAY/NIGHT Auto-switch The speed dome delivers color images during the day; as light diminishes at night, it switches to night mode and delivers black and white images with high quality.
- Page 36 IR Speed Dome User Manual includes Zoom, Pan/Tilt angle, Preset title, and Time, etc Preset Freeze Frame This feature freezes the scene on the monitor when going to a preset. This allows for smooth transition from one preset scene to another and also guarantees that masked area will not be revealed when going to a preset.
- Page 37 IR Speed Dome User Manual The baud rate of the speed dome can be configured by the menu without need of DIP switch settings. Time Task A time task is a preconfigured action that can be performed automatically at a specific date and time.
- Page 38 First Choice for Security Professionals...