Subscribe to Our Youtube Channel
Related Manuals for Trebs CC-120
Summary of Contents for Trebs CC-120
- Page 1 User manual Bluetooth Hands free & 2.4Ghz Wireless Rearview Mirror System Model No.: CC-120 TRE -BS-132...
-
Page 3: Packing List
CONTENTS 1.Foreword 2.Packing List 3.Structure 4.Installation 5.Specifications Comfortcam is not responsible for any damage resulting from installation and use of this product. *2.4 GHz devices as e.g. cell phones, navigation, bluetooth and Wi-Fi system scan have influence on the performance of this product. - Page 4 FOREWORD CONGRATULATIONS. CC-120 is a Bluetooth Hands free & 2.4GHz Wireless Rearview Mirror System with 3.5" TFT-LCD monitor. The system can make you to drive more safely and more convenient, and also provides you more recognition of backside image display. The Rearview Camera, when used as described, will give you years of dependable service in your car, or mini-van.
- Page 5 1 Rearview Camera: Wired Camera with Night Vision. 2.Monitor: 3.5 inch TFT-LCD, with 960*240 resolution 3.Earphone 4.Wireless Transmission Box : Connected to wired camera, car power wire. It transmits signals to monitor. 5.Power Adapter: 12 Volt Car Power Adapter and built in 2.4GHz wireless receiver Audio cable for listening MP3.
- Page 6 Rearview Camera Frame IR LEDs Lens Power plug Wireless Transmission Box Wireless Transmission Box Power Wire Connect Wire Rearview Camera TFT-LCD Monitor...
- Page 7 We advise to test the system before installation to prevent any damage on the vehicle. Follow the steps mentioned below precisely to test the system. 1. Connect 12V car adaptor to the vehicle's cigarette lighter and connect the black and yellow plugs to the monitor. 2.
- Page 8 INSTALLATION Installation of the camera: 1. Loosen the license plate bolt or screw, and then remove the license plate on the rear of your car. 2. Drill one hole for power cable in the middle of below license plate, where the camera will exist.
- Page 9 Wireless Transmission Box Installation 1. Wiring Connector Diagram +12V REV LAMP Wireless Camera Transmission Reverse Lamp BLACK GROUND 2. Basic Installation 1). Find proper spaces for install the transmission box. 2). Connect the red wire of the transmitter to the positive wire of the back up light.
- Page 10 Insert the existing Insert the wire to Crimp tap then wire to be tapped. be attached. close lock...
- Page 11 3. BLUETOOTH installations Please refer to extra manual of “BLUETOOTH User manual 3.0”. Installation of the monitor: 1. Camera is be attached the front rearview mirror instead of the front rearview mirror. 2. Connect power of the monitor. To use the car power adapter included in the package to get the power.
-
Page 12: Specifications
SPECIFICATIONS Items CC-120 Imaging Sensor CMOS Total Pixels 720×480(NTSC)720×576(PAL) Horizontal View Angle 80 degree Transmission Power 2mW/FCC,10wm/CE 0 Lux (IR ON) Minimum Illumination IR Night Range Power Supply Supplied By Transmission Box Consumption Current(Max.) 120mA × × Dimensions(W D H ) 525×148×45(mm) - Page 13 CAUTIONS The system voltage is 9V~15V. Do NOT use the system vehicles with voltage system higher than 15V; this will cause irreparable damage. 2.The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
-
Page 14: Declaration Of Conformity
Trebs BV. Thermiekstraat 1 6361 HB Nuth The Netherlands Website: www.trebs.nl email: info@trebs.nl Trebs Comfortcam is a brand of Trebs BV. All other brands in this manual and/ or packaging do not belong to Trebs BV and have another justified holder. - Page 15 EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Need help?
Do you have a question about the CC-120 and is the answer not in the manual?
Questions and answers