Related Manuals for Gundlach 1027 Series
Summary of Contents for Gundlach 1027 Series
- Page 1 Owner’s Manual Nos.1027 /1037 Series Bridge Saws 1027 1027 1037 Before operating the unit, please read this manual thoroughly, and retain it for future reference.
-
Page 2: Table Of Contents
Do’s & Don’ts for Blades WEAR BREATHING PROTECTION 17, 18 Saw Maintenance 19, 20, 21 Water Pump Maintenance Troubleshooting 23, 24, 25 Notes Warranty 27, 28 Replacement Parts List 29, 30, 31, 32, 33, 34, 35 No.1027 Saw Exploded View No.1037 Saw Exploded View... -
Page 3: General Safety Rules
General Safety Rules Unpack, Assembly & Set-Up Unpack • Never use the machine improperly or work in an unsafe manner. • Always wear safety goggles, dust mask, and ear protection while operating Open the container, carefully lift the saw (to comply with ANSI-Z87.1). the saw frame handles and •... -
Page 4: Specifications
, and operation. similar materials. Position Lock Cutting Head Powerful 1-1/2HP Induction Motor cuts larger materials SPECIFICATIONS 1027 1037 1-1/2 HP 1-1/2 HP Horse Power 115 votls 115 volts Volts Rubber Matted... -
Page 5: Saw Stand Assembly
BLADE INSTALLATION No. 1010-ST SAW STAND ASSEMBLY Folding Stand (1027 Optional) 1. Remove the folding stand 1. Loosen the knurled nuts from its box. securing the blade guard 2. Swing the working bench and remove the guard. up-right. Open the two legs 2. -
Page 6: Cutting Head Installation
CUTTING HEAD INSTALLATION WATER PUMP INSTALLATION 3. Fill the water tray so that 1. Remove the water pump 1. Slide the motor into the body of the water intake is fully from the box and check the cutting head mainframe, holding immersed. -
Page 7: The Rip Guide
THE RIP GUIDE (Optional) OPERATING THE SAW: continued á The No. 884 Universal Tile 5. After the cutting operation Guide is a two-piece is finished, prevent assembly consisting of a accidental restarting of the template base and a saw by pushing the unique detachable ruler emergency stop from the guide. -
Page 8: The Cutting Table
THE CUTTING TABLE CUTTING DEPTH Features: The recommended cutting depth is ¼" below the cutting table surface. The cutting clearance has been fixed from original design. • The easily removable cutting table is covered with an anti-skid rubber coating, which allows the material Blade Diameter Cutting Depth being cut to sit still on the... -
Page 9: Electric Motor Specifications
ELECTRIC MOTOR SPECIFICATIONS Features: • Horsepower 1-1/2 H.P . • Volts 115 V • Amps 15 Amps 45 /90 RIP GUIDE ° ° • Motor RPM 3450 No. 1000-35 • Cycle 60Hz • Phase Recommendations: • It is recommended that a 15 AMP CIRCUIT be used while operating this saw. - Page 10 Wet Cut Blades Dry Cut Blades DO'S DON'TS DO'S DON'TS Do not operate the Inspect blades daily In addition to the In addition to the saw without safety for cracks or uneven following, always following, always guards in position. wear. follow wet follow wet Always use...
- Page 11 WARNING: For your safety, before performing any maintenance on the saw turn e. Do not "rinse" the g. After wet cleaning, try off the power switch and unplug the power cord. bearings of the drive the machine on a elements to prevent power outlet which General Rules them from running dry.
-
Page 12: Water Pump Maintenance
·Before & After A Prolonged Time Temperature Changes Ambient Temperature - To prevent the water in the pump Before not using the -Clean and lubricate all movable · and cooling system from freezing, machine for a prolonged parts. DO NOT GREASE THE Below 37 F (Winter) °... -
Page 13: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION PROBLEM POSSIBLE CAUSE SOLUTION heck that the machine is - Have the motor checked Machine does - Power cord not properly - Drive motor no longer runs properly connected to the by a qualified electrician not run when fixed/plugged in at rated speed (r.p.m.) -
Page 14: Notes
TROUBLESHOOTING NOTES PROBLEM POSSIBLE CAUSE SOLUTION Cracks in or near - Use a softer blade - Saw blade too hard the diamond - Have the fixed flange -Fixed flange is worn out segment replaced - Replace the bearing - Motor shaft bearing of the motor shaft - Use appropriate type of saw Saw blade is... -
Page 15: Warranty
LIMITED WARRANTY LIMITED WARRANTY 1. SAW: To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original packaging or packaging For a period of one (1) year from the original date of purchase, if the product affording an equal degree of protection, to service facility authorized by is determined to be defective, we will repair or replace the product, at its us, along with proof of purchase in the form of a bill of sale, within the... -
Page 16: Replacement Parts List
REPLACEMENT PARTS LIST 1027 REPLACEMENT PARTS LIST 1027 PART NAME PART NAME PART No. PART No. Guide Rail 102701 Cutting Head Position Bracket 102738 Ruler Guide Bolt (set of 4)/M6X16 102702 Motor Position Lock Knob 102739 Supporting Post Lock Bolt (set of 6)/ M5X20... - Page 17 102763 Front Support Post Plate 102706 Motor Fan 102766 Center Lock Nut (set of 2)/ M10 102707 Motor Fan Cover Screws 102767 Front Rubber Mat Cutting Table (SDT-1027) 103708 Rubber Plate 102768 Drain Plug 102709 Capacitor 102759 Main Metal Frame...
- Page 18 REPLACEMENT PARTS LIST 1037 REPLACEMENT PARTS LIST 1037 Handle Bar 102736 Water Pump Cord 102711 Handle Rubber Sleeve 102732 Circuit Breaker Pushbutton Boot S1000-04.1 Cutting Head Position Bracket 102738 Toggle Switch Boot S1000-03.2 Motor Position Lock Knob 102739 Metal Frame Mount 102776 Circuit Breaker 102740...
- Page 19 EXPLODED VIEW No. 1027 DIAGRAMA DE LA SIERRA No. 1027 28 29 Motor Motor Motor Parts Motor Parts Partes del Motor Partes del Motor Universal Tile Guide 45 /90 Universal Tile Guide 45° /90° ° ° Multiple Wrench Multiple Wrench °...
- Page 20 EXPLODED VIEW No. 1037 DIAGRAMA DE LA SIERRA No. 1037 28 29 Motor Motor Motor Parts Motor Parts Partes del Motor Partes del Motor (Optional) Universal Tile Guide 45 /90 Universal Tile Guide 45° /90° ° ° Multiple Wrench Multiple Wrench Llave Multiple Llave Multiple Guia azulejos universales 45 /90...
Need help?
Do you have a question about the 1027 Series and is the answer not in the manual?
Questions and answers