Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Mantis 8530
Summary of Contents for Mantis 8530
- Page 1 OPERATOR / PARTS MANUAL Electric Chainsaw Warning! Read through the operating instructions carefully and observe the instructions contained herein. Familiarize yourself with the machine, its correct use and the safety devices by means of these operating instructions. 8530...
- Page 2 WARNING CALIFORNIA Proposition 65 Warning Battery post, terminals, wiring insulation, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. WASH HANDS AFTER HANDLING. Electric Chainsaw Operatorʼs Manual...
- Page 3 Your safe use of this Mantis product is one of our prime design objectives. Many safety features are built in, but we also rely on your good sense and care to achieve accident-free operation. For best protection, study the manuals thoroughly. Learn the proper operation of all controls.
-
Page 4: Table Of Contents
9.1 The machine does not start up 9.2 Chain does not run 9.3 Sparks fly at the motor 9.4 Oil does not flow 10. Repair service ..................................14 11. Environmental Protection ..............................14 12. Technical Data ..................................14 MANTIs LIMITED WARRANTY Electric Chainsaw Operatorʼs Manual... -
Page 5: Safety Rules & Warnings
Remove plug immediately if the Attention, kick-back! Hold tool with both hands! Attention: Environmental power cord is damaged or cut Protection! This device may not be disposed of with general/ household waste. Disposeof only at a designated collection point. Contact us at www.mantis.com... -
Page 6: Introduction To The Operating Instructions
2. Introduction to the Operating Instructions d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part These Operating Instructions are intended to facilitate your becom- of the power tool may result in personal injury. ing acquainted with the machine and using it in accordance with the e) Do not overreach. -
Page 7: Important Instructions For Your Personal Safety
8. Keep the running chainsaw from touching the ground or wire 6. Only lend or give this chainsaw to persons who are familiar fences. with its use. Also give them these Operating Instructions. Contact us at www.mantis.com... - Page 8 WARNINg WARNINg The operation of any power tool can result in foreign To avoid serious personal injury, do not attempt to use objects being thrown into your eyes, which can result this product until you have read this Owner’s Manual in severe eye damage.
-
Page 9: Names Of Parts
Failure to comply could result in accidental second is sufficient to inflict serious injury. starting and possible serious personal injury. Use a gFCI (ground fault circuit interrupt) protected supply with a tripping current of 30 mA or less. Contact us at www.mantis.com... -
Page 10: Starting Up
5. starting Up • The chainsaw is equipped with an oil metering mechanism. The volume of oil can be adjusted between 3 levels (A - low oil supply, B - 5.1. Filling the Oil Tank and Adjusting the Oil supply (Fig. 1-3) normal oil supply, C - high oil supply) depending on the type of wood being cut (Fig. -
Page 11: Connecting The Chainsaw
(19) out into position A. Now insert the loop of tion (5) is locked in the operating position. To do this, pull back the cable from below into the extension cord cleat. Once you have released hand protection in the direction of the handle. Contact us at www.mantis.com... -
Page 12: Rundown Brake
6.2. Rundown Brake In accordance with the latest regulations, this chainsaw is equipped with a mechanical rundown brake. This brake is connected to the chain brake and stops the running chain after the chainsaw has been switched off. It is activated by releasing the ON/OFF switch. The rundown brake avoids injuries through the coasting of the chain. -
Page 13: Spiked Bumper
Check whether the power cable is undamaged. • Repeat several times if necessary, changing the point where you plant If neither case applies, take the chainsaw to a specialized workshop the spiked bumper. or the works after-sales service. Contact us at www.mantis.com... -
Page 14: Chain Does Not Run
Properly dispose of packaging material that is not required any longer via your local waste paper disposal system. 12. Technical Data Electric Chainsaw Mantis 8530 Rated Voltage Nominal Frequency Rated Output 1400 Nominal current 11.7... - Page 15 MANTIS will repair or replace, at its option, any part or parts of the product found to be defective in material or workmanship during the warranty period. Warranty repairs and replacements will be made without charge for parts or labor.
Need help?
Do you have a question about the 8530 and is the answer not in the manual?
Questions and answers