1. Manuals
  2. Brands
  3. Newton Security Manuals
  4. Security Sensors
  5. T1010
  6. Installation and operation manual

Newton Security T1010 Installation And Operation Manual

Tailgating / piggybacking detection system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
T-DAR
®
Model T1010 and Model T2010
Single Door
Two Door
TAILGATING / PIGGYBACKING DETECTION SYSTEM

INSTALLATION AND OPERATION MANUAL

Newton Security Inc.
st
443 SW 41
Street
Renton, WA. 98057 USA
www.newtonsecurityinc.com
Revision 4.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T1010 and is the answer not in the manual?

Questions and answers

Related Manuals for Newton Security T1010

Summary of Contents for Newton Security T1010

  • Page 1: Installation And Operation Manual

    T-DAR ® Model T1010 and Model T2010 Single Door Two Door TAILGATING / PIGGYBACKING DETECTION SYSTEM INSTALLATION AND OPERATION MANUAL Newton Security Inc. 443 SW 41 Street Renton, WA. 98057 USA www.newtonsecurityinc.com Revision 4.0...

  • Page 2: Introduction

    INTRODUCTION Tailgating/Piggybacking Access control systems are the heart of most security systems. From smart cards to fingerprinting and even iris recognition technology, there are many different systems in place to restrict access to secure areas. But there is one way to completely bypass every one of these systems - with the simple act of holding the door open.

  • Page 3: Critical Elements For A Successful T-Dar Installation

    Critical Elements for a Successful T-DAR Installation ® The T-DAR system does a superb job of detecting violations of access control security systems. In order to accomplish this task, the T-DAR requires several critical elements and/or signals from the door and the access control system as detailed in this manual.

  • Page 4: Table Of Contents

    INTRODUCTION......................1 Tailgating/Piggybacking..................1 ® T-DAR Solution .....................1 Critical Elements for a Successful T-DAR Installation ..........2 PRODUCT DESCRIPTION ..................6 General Description ....................6 T-DAR Models Covered In This Manual ..............7 T-1010 Single Head (Single Door) Systems ............7 T-2010 Two Head (2 Independent Doors) Systems ..........7 T-DAR Models Not Covered In This Manual............7 T-DAR Product List for the Systems covered by this Manual .........8 SPECIFICATIONS ....................10...
  • Page 5 Relay Connections....................35 CONNECTION TO LAPTOP / LAN ................36 To Configure the Host TCP/IP Connection ............36 Install the Software ....................36 User Interface (UI) Application ................36 Door Control Unit Application................37 Configure Connection ...................38 Connecting via Ethernet..................38 To Connect via Serial Ports ..................39 Connecting via Serial Port.................39 Figure 17 - Configure Connection ..............39 Configuring the T-DAR ..................40...
  • Page 6 Installer I/O ......................59 Portal Selection ....................59 Door Control......................60 Camera Geometry.....................61 System Log......................62 Advanced Tab.......................63 OPERATION ......................64 Important Safety and Warning Information ............64 Critical elements to maintain a properly operating T-DAR installation ....65 Front Panel Indicator LED’s on the CB110/210 ............67 Programming the Annunciator ................68 Maintenance ......................69 Troubleshooting....................70...

  • Page 7: Product Description

    PRODUCT DESCRIPTION General Description Several configurations of the T-DAR Series are available. The models covered in this manual are all inside systems and have the following features: ♦ Confirm only one human for each authorized entry, including multiple authorizations for each escorted visitor ♦...

  • Page 8: T-Dar Models Covered In This Manual

    ♦ Thrown Object Detection Systems ♦ Escalator Systems ♦ Revolving Doors ♦ Time and Attendance Tracking ♦ Waiting Line Tracking ♦ Directional Control Systems Consult Sales at Newton Security Inc. for T-DAR Models and Manuals for systems not covered in this manual.

  • Page 9: T-Dar Product List For The Systems Covered By This Manual

    Please use the following data when contacting your sales representative for additional components. Special configurations are also available. Item Model Number Description 1 Door T1010 Complete Tailgate Detection Complete T-DAR System System-with CB110 Control Unit, 1 DC 200LP Camera Head, and 1 S100 Annunciator...
  • Page 10 Cable Extender/Amplifier EA101/EA101A Cable Extender--Extends the distance from the door to the EA101 T-DAR Control Unit for more powered by the than the standard 200’. T-DAR unit Extends the cable length for the DC200LPLP Stereo EA101A Camera Head, the S100 powered by Annunciator Unit and the I100 plug mounted...

  • Page 11: Specifications

    SPECIFICATIONS CB110/210 Control Unit Figure 1- T-DAR Control Unit Size: 5.726” x 16.365” x 11.643” Weight: 26 lbs Enclosure: Bent steel; completely enclosed with door Mounting: Mounting via 4 x 1/4 " holes on back panel tabs (Optional mounting brackets available) Standard Operating Temperature: 40 to 110 degrees F, (optional high and low temperature systems available) Storage Temperature: 0 to 125 degrees...
  • Page 12 Serial Connections 2 RS232 and 4USB Figure 2 - T-DAR Control Unit CAD...

  • Page 13: S100 Annunciator

    S100 Annunciator Figure 3 - T-DAR Annunciator Size: 6.00” x 8.13” x 7.19” Weight: 5 lbs Enclosure: Bent steel, with high impact plastic indicator Mounting: Mounting via 4 x 3/16" holes on back panel tabs Standard Operating Temperature: 40 to 125 degrees F, (optional high and low temperature systems available) Storage Temperature: 0 to 150 degrees F Input Voltage/Current...
  • Page 14 Figure 4 - T-DAR Annunciator CAD...

  • Page 15: Dc200Lp Stereo Tracking Head

    DC200LP Stereo Tracking Head Figure 5 - T-DAR Stereo Tracking Head Size: 7.00” x 2.50” x 2.50” Weight: 2.2 lbs Enclosure: Bent steel Mounting: Mounting via 4 x 1/8" holes on back panel tabs (Optional mounting brackets available) Standard Operating Temperature: 40 to 125 degrees F, (optional high and low temperature systems available) Storage Temperature: 0 to 150 degrees F Input Voltage/Current...
  • Page 16 Figure 6 - T-DAR Stereo Tracking Head...

  • Page 17: I100 Door Position Encoder

    I100 Door Position Encoder Figure 7 – T-DAR Door Encoder Size: 2.40” x 2.50” x 2.40” Weight: 13.5 ounces Enclosure: Machined Delrin Mounting: Mounting via 4 x 1/4-" holes on back panel (Optional mounting brackets available) Standard Operating Temperature: 40 to 125 degrees F, (optional high and low temperature systems available) Storage Temperature: 0 to 150 degrees F Input Voltage/Current...
  • Page 18 Figure 8 – T-DAR Door Encoder...

  • Page 19: Ec105 Event Camera

    EC105 Event Camera Figure 9 – T-DAR Event Camera Size: 2.13” x 1.81 x 2.36 Weight: 10 Ounces Enclosure: Extruded Aluminum Mounting: Mounting via 1 ¼-20 indexed threaded hole on top cover (Optional mounting brackets available) Standard Operating Temperature: 40 to 125 degrees F, (optional high and low temperature systems available) Storage Temperature: 0 to 125 degrees F Input Voltage/Current...
  • Page 20 Figure 10 – T-DAR Event Camera...

  • Page 21: Ea101/Ea101A Cable Extender/Amplifier

    EA101/EA101A Cable Extender/Amplifier Figure 11 – T-DAR Cable Extender/Amplifier Size: 3.55” x 3..55” x 3.00” Weight: 1.5lbs Enclosure: Extruded Aluminum Mounting: Mounted via back panel mounting holes Standard Operating Temperature: 40 to 125 degrees F, (optional high and low temperature systems available) Storage Temperature: 0 to 125 degrees F Required to extend the standard maximum distance of 200’...
  • Page 22 Figure 12 – T-DAR Cable Extender/Amplifier CAD...
  • Page 23 Ea101 Vs. Ea101A Figure 13 - EA101 Ø Use the EA101 for the first extender at 150 – 200 feet Ø No external power require-powered from the TDAR Control Unit Figure 14 - Ea101A W/ power adapter Ø Use the EA101A for additional extenders for each 150- 200 foot extension Ø...

  • Page 24: Installation

    INSTALLATION Important Safety and Warning Information The T-DAR system may contain, produce and present the hazard for electrical shock or burns with the cover removed. There are no user serviceable parts under the interior panels. Only trained authorized personnel may perform maintenance or repair.

  • Page 25: Tips For A Successful T-Dar Installation

    Tips for a Successful T-DAR Installation Six of the most critical fundamentals are: Valid access grant signals must be immediate. The valid access signal from the access control system must by occur at the same time or before the door is unlocked to allow an entry and must have duration of at least 300 ms.

  • Page 26: Physical Installation

    LineLock input is critical if low frequency fluorescents are utilized for lighting. An ac wall-mounted transformer is included in the T-DAR control unit. If the lighting in the area that is protected by the T-DAR is provided by low frequency (older style-line frequency) fluorescents, this transformer or other low voltage AC source must be used to ensure proper operation of the T-DAR system.

  • Page 27: Site Considerations

    Site Considerations There are several factors that must be considered when determining the application of T-DAR for the solution of tailgating and piggybacking. These factors are detailed as follows: Consistent Downward Lighting The T-DAR requires adequate and consistent downward lighting to properly detect tailgate violations.

  • Page 28: Before You Begin

    This distance is 200 feet, and should not be exceeded unless a distance extender is used. Information about the cost and part number of the Data Extender is available from the Newton Security. Whenever possible, local devices shall be placed on the secure side of the portal being monitored to reduce the risk of vandalism and attempts to defeat.

  • Page 29: Stereo Tracking Head Selection

    T-DAR User Interface. Lighting System – Visible or Near IR Order the correct head for the lighting at your installation. Newton Security supplies Stereo Camera Heads for both types of lighting systems. Distance from Stereo Camera Head to Floor Newton Security supplies stereo camera heads pre-focused and set to the correct field of view for various camera heights.

  • Page 30: Stereo Tracking Head Placement

    Stereo Tracking Head Placement The stereo camera head needs to be located based upon the calculations in the camera head placement chart. Failure to place the camera in the correct location will lead to false alarms or an altogether failure to detect violations. The calculations in this chart are based upon door size, camera head height, and lens focal length.

  • Page 31: Stereo Tracking Head Placement Chart

    Stereo Tracking Head Placement chart Distance from the center of the Distance from the front of the Type of Camera Stereo Camera Head to the door Stereo Camera Head to the floor Inches Inches 84 to 96* 2.1 to 2.44* 12-20 31-51 (8’)

  • Page 32: Component Mounting And Electrical Connections

    Component Mounting and Electrical Connections Control Unit The door control unit should be mounted on a wall in a vertical orientation. The unit is equipped with mounting tabs that will accommodate ¼ inch mounting hardware. The unit should be mounted and grounded in accordance with National Electrical Code (NEC) guidelines.

  • Page 33: Stereo Tracking Head

    Stereo Tracking Head The camera head can be mounted utilizing the mounting tabs that accommodate up to a number 12 screw or a Newton MK200 ceiling mount kit designed to work in a variety of applications such as drop tile ceiling or hard ceiling. Refer to the MK 200 manual addendum in this manual for specific details.

  • Page 34: Event Camera

    Event Camera The event camera should be mounted in accordance with the manufacturer’s requirements. It is strongly recommended that vandal-resistant camera enclosures and wire ways be incorporated in the installation. 1. Install, terminate, and install one video coaxial cable at the event camera. 2.

  • Page 35: Connection To Access Control Systems

    CONNECTION TO ACCESS CONTROL SYSTEMS Door Valid Access Grant Switch The valid access grant switch must be electrically isolated from the access control system to allow for proper operation. This will typically require the installation of a double pole/double throw relay that controls the lock and also provides an output to the T-DAR system.

  • Page 36: Relay Connections

    Relay Connections The T-DAR T-1010 and T-2010 control units are equipped with four relays on the General connector plus one relay on each of the Portal connectors. These relays may be used to signal various alarm conditions based on user configurable options in the user interface.

  • Page 37: Connection To Laptop / Lan

    1. The factory set TCP/IP connection on the host computer is typically set to “automatic”. Changing these settings will establish a connection to the Newton Security Inc. TDAR, but may disconnect or even conflict with your current network system. Please check with your network administrator if you have any questions.

  • Page 38: Door Control Unit Application

    After the software is loaded, the UI may be launched from the start menu on the host computer. Start -> Programs -> Newton Security Inc -> T-DAR Once the system hardware is configured, the UI application is no longer needed and the T-DAR will run unaided.

  • Page 39: Configure Connection

    Configure Connection Selecting Configure Connection from the menu opens the dialog box to specify connection type, IP address and connection preference. Figure 18 - Configure Connection Connecting via Ethernet 1. serial number and factory-set IP address of each vision system is printed on the inside lower corner of the door of the unit, in the following format: SN: CB200101000102 IP: 10.3.2.21 2.

  • Page 40: To Connect Via Serial Ports

    To Connect via Serial Ports Connecting via Serial Port Figure 19 - Configure Connection 12. Select Connection then Configure Connection from the application’s menu bar. 13. Select Serial Port and Com port I.E (Com1, Com2, ETC…) from the Configure Connection dialog box. 14.

  • Page 41: Configuring The T-Dar

    Configuring the T-DAR The T-DAR user interface (UI) is used to set-up and optimize the detection performance of the system. The following instructions provide guidelines that will enable the installer to quickly and effectively place the T-DAR system in service. Viewing Images The installer should select the Show Camera Views view from the monitor page.

  • Page 42: Capturing Events

    If the system still does not respond, call for Newton Security or your integrator for additional support. Capturing Events Alarm event video is captured and stored in volatile memory on the system. There is no onboard persistent storage of alarm video information; if the system power is interrupted, all stored video will be lost.
  • Page 43 9. Click on the initial set-up page and draw a green line at the base of the door jam. This will automatically set the proper regions of interest 10. The System should now be operating and ready for testing. (See testing the System Pg.

  • Page 44: User Interface

    USER INTERFACE Detailed Information About the T-DAR User Interface Software The T-DAR User Interface (UI) software consists of eight tabbed pages labeled as follows; Initial Set-up, Monitor, Setup I/O, Setup View, Installer I/O, Installer Camera Settings, System Log, and Advanced. The User Interface Tab pages are navigated by a series of tabs and menus.

  • Page 45: File Menu

    File Menu Figure 21 – File Tab Selecting FILE from the menu, opens a window that allows the options for saving and restoring settings. These settings can be stored in another computer. In the event of having to restore the software, any configuration adjustments can be recalled from this file.

  • Page 46: Exit

    Exit Clicking the Exit button closes the User Interface. The T-DAR will continue to run and perform security inspections even with this interface disabled. Settings and parameters that have been changed with the User Interface will persist while disconnected. The Host computer will be completely removed from and have no communications with the operating unit.

  • Page 47: Connection Menu

    Connection Menu Figure 22 – Connection Connect Establishes communication between the UI application and the T-DAR hardware. A connection must be established before proceeding to the run menu or before performing subsequent UI operations. If the T-DAR IP has been previously configured, selecting Connect from the menu will enable the User Interface.

  • Page 48: Debug Tab

    Debug Tab: Figure 23 - DeBug Tab Hide Debug Menu This allows you to hide the Debug menu. The Debug menu is not for general use, it is designed to be used by the system Admin to troubleshoot the system. Do not make any changes using this menu if you have not been properly trained.
  • Page 49 Erase EEPROM This function erases all current setting and restore unit back to factory defaults. Dump EEPROM This feature allows you to save the current EEROM setting to a file, for technical analyst/troubling support from manufacturer. IP Networking IP Networking allows you to change the IP address, subnet mask, and gateway that you unit uses to connect to your company internal network.

  • Page 50: Initial Set-Up

    Initial Set-up The initial Set-up tab is the most important tab in the UI. Here the technician will enter the camera height, Distance to floor, orientation of cameras, load camera calibrations, and the most important element draw the Green line (line of demarcation) for automatically setting up the users regions.
  • Page 51 Green Line With the crosshair draw a green line at the base of the door, which the unit is installed (as shown). This will automatically set-up the regions for scanning.

  • Page 52: Display

    Monitor Tab The Monitor page consists of a various menus that allow the user to change between cameras and camera views. Below is a list of the various camera views available for selection by way of radio buttons. Also on this page is an Alarm Reset button for each Portal, as well as statistics for each Portal.

  • Page 53: Alarm And Events

    Alarm and Events A button for manually resetting the alarm is available in the UI. Clicking Reset Alarm will clear an alarming security event and return the system to its normal monitoring mode. The Events counter is a running log of the security scenarios being monitored by the T-DAR.

  • Page 54: Setup I/O

    Setup I/O The Setup I/O page consists of a pull-down, an Alarm section, a Reset Event Statistics button, a Change Admin Password button, a Portal Name box, a Time section, and a Policy section. These items are detailed below. Figure 26 - Set-up I/O Alarm The alarm section consists of check boxes that allow the user to disable all of the various alarm annunciation provided by the Annunciator Unit.
  • Page 55 Policy The Allow Multiple Entries per Access Cycle check-box is used to set the T-DAR system to stack cards. Card stacking to the ability of T-DAR to recognize multiple valid access signals and to retain that number for as long as the door is open or 15 seconds has passed, whichever comes first.

  • Page 56: Change Admin Password

    Change Admin Password The admin password is the second highest level of access available to users. This allows access to the Monitor, Setup I/O, and Setup View tabs of the system. To configure the password, the button is clicked and then a password is typed either on the on-screen keyboard or on the host computer keyboard.

  • Page 57: Installer Camera Settings

    Installer Camera Settings The Installer Camera Settings page consists of a pull-down, an Image Type section, an Update Now button, a Viewing Window, a Physical Setup section, a Sensitivity Section, and a Configuration Section. These are detailed below: Figure 27 - Installer Camera Settings Image Type The image type section is used to select what camera is viewed when the system process is stopped.

  • Page 58: Physical Setup

    Physical Setup The physical setup section consists of two buttons used to control the camera calibration process. The Calibrate button is used to teach the system about the scene that is being monitored. When the system has learned the environment, the tracking image will become stable and black unless objects are detected.

  • Page 59: Minimum Head Size

    Minimum Head Size The minimum head size slider controls the value that determines the smallest object that can be called a head without incorrectly identifying carried objects as a head. Crawler Sensitivity The crawler sensitivity slider controls the value that determines the size a specific object must be larger than to be called crawler (crawling person).

  • Page 60: Installer I/O

    Installer I/O Figure 28 - Installer I/O The Installer tabs are for configuring the interface with the other components of the installed security system. Provisions for configuring the Outputs, Door Setup and Sensitivity are accessed from these pages. These pages are password protected for Installer and System Administrators use only.

  • Page 61: Door Control

    Door Control The configurable options of the Door Control section allow for adapting T-DAR to the existing peripherals to correctly trigger the unit. The logic state for these devices, as used by the T-DAR, is selected by clicking the check box that reflects the installation.

  • Page 62: Camera Geometry

    Outputs There are five relays on a CB-110 and six relays on a CB-210 for connecting signals through the T-DAR. The first two relays are for Portal 1, Relay Portal 1-1 and Relay Portal 1-2. Portal 2 has the next two relays, Relay Portal 2-1 and Relay Portal 2-2. There is one spare relay for each portal, Portal 1 Relay Spare and Portal 2 Relay Spare.

  • Page 63: System Log

    System Log This tab allows you to see the activity of the system, when doors open and close, what alarms have been active and what inputs and outputs have been triggered. Figure 30- System Log...

  • Page 64: Advanced Tab

    The Advance page consists of a number of user definable options that can override several of the standard controls of critical system functions detailed in previous tabs. These items should only be adjusted at the direction of qualified Newton Security Personnel. No Additional description of these functions is being provided here.

  • Page 65: Operation

    OPERATION Important Safety and Warning Information The T-DAR system may contain, produce and present the hazard for electrical shock or burns with the cover removed. There are no user serviceable parts under the interior panels. Only trained authorized personnel may perform maintenance or repair.

  • Page 66: Critical Elements To Maintain A Properly Operating T-Dar Installation

    Critical elements to maintain a properly operating T-DAR installation Once correctly installed, the T-DAR system does a superb job of detecting violations of access control security systems. In order to accomplish this task, the T-DAR requires several critical elements and/or signals from the door and the access control system as detailed in this manual.
  • Page 67 Lighting Conditions may have changed. Adequate and consistent lighting are required for accurate operation of the T-DAR system. The T-DAR system uses stereo video analysis to determine three-dimensional characteristics of targets and requires sufficient lighting to perform this task. Equal and consistent lighting allows the system to identify and track targets in all areas of the detection pattern.

  • Page 68: Front Panel Indicator Led's On The Cb110/210

    Front Panel Indicator LED’s on the CB110/210 LED # Description T-DAR Status Firmware and software not running Flashing Orange Firmware running-software in self-check Flashing Green Firmware and software running-Normal Flashing Red Firmware running-software stopped Any color- steady state Firmware and software stopped Ethernet connection No Ethernet connection Green...

  • Page 69: Programming The Annunciator

    Programming the Annunciator Voice Announcements may be changed to suit the installation. Figure 33 - Annunciator Internal View To change the Voice Announcement via microphone: Gain access to the printed circuit board within the Annunciator. Remove the (6) 6/32 Phillips head screws that attach the top cover. Ensure that JP1 is set MIC., JP2 is set REPEAT, JP3 is set to RECORD and JP4 is set to SIREN.

  • Page 70: Maintenance

    Depress and hold the record switch SW1 and speak the new message clearly into the unit. Release the record switch when complete. Your new message should now be playing repeatedly. If satisfied with the new message, restore the STR DIP switch selected for reprogramming to its normal off position.

  • Page 71: Troubleshooting

    Troubleshooting Troubleshooting guides This section provides fundamental hardware troubleshooting for the T-DAR. For problems that are not covered in this section, contact your local Newton Security Inc. Authorized Distributor. Tips for getting a good image ♦ Make sure that the light is consistently illuminated across the inspection area.

  • Page 72: Problems Communicating With The T-Dar

    ♦ Turn off the computer, restart, and try again. If the above suggestions do not provide results, follow the procedures below to further troubleshoot communications: Call your Newton Security Inc. Authorized Distributor Arrange with your local distributor to substitute a working T-DAR unit and laptop to determine where the problem exists.

  • Page 73: Imaging Problems

    Camera Head. ♦ Point the Imager at a bright light. If the live image is entirely black, then contact your Newton Security Inc. Authorized Distributor.* ♦ Random Pixels This is commonly caused by electrical noise generated by...
  • Page 74 IMAGING PROBLEMS (CONTINUED) ♦ Random Pixels Remove the unit from its current mounting- repeat Step 2 Appear In the Video Change the power source-repeat Step 2. Output (continued) Change the ground connections-repeat Step 2. Disconnect controllers and drives one at a time from the control panel-repeat Step 2.

  • Page 75: All Monitored Events Are Failing

    All Monitored Events Are Failing If a working installation suddenly returns failed inspections for all or most of the inspections, the T-DAR Stereo Camera Head has probably been bumped, or something has obscured the field of view. A change in lighting conditions is another possible problem area.

  • Page 76: Detailed Specifications

    DETAILED SPECIFICATIONS CB110/210 DC Input Specifications Minimum-Maximum Voltage Range 10.6 – 26.8 VDC Operating Voltage Range 12 – 24 VDC Peak Voltage (Non-continuous) 30 VDC Minimum Pulse Width 0.4 mSec ON Voltage Level >10 VDC OFF Voltage Level < 2 VDC Maximum.

  • Page 77: Lower Power Panel Connections

    Lower Power Panel Connections Upper Panel Front Panel Figure 35 - Control Unit Connections...

  • Page 78: Upper Front Panel Connections

    Upper Front Panel Connections Figure 36 – Upper Panel Connections Camera 1a: Input, BNC connector from Stereo Camera Head1, camera1 Camera 1b: Input, BNC connector from Stereo Camera Head 1, camera 2 Event Camera 1: Input, BNC connector from external Camera for Event Capture Camera 1 RJ-45: Interface, Standard 10BaseT Cat-5 Ethernet cable to Stereo Camera Head for Power/Control Event Cam 1 RJ-45: Not Used...

  • Page 79: Front Panel Connections

    Front Panel Connections Figure 37 - Control Unit Connections Phoenix Style connectors, top to bottom CONNECTOR A, General 1 Pins 1-8: Relay 1-4 A&B, general purpose Form A relay contacts, normally open Pin 9: Line Lock, for use with 6-30 vac power for syncing to local power grid Pin 10: System GND, for use with Line Lock Pin 11: +24VDC Pin 12: System GND...
  • Page 80 Pin 3: Input, Sets logic level for inputs on General Connector 2. Connect to Ground for Logic High (+12V=Trigger) on inputs. Connect to +12V for Logic Low (GND = Trigger). Pin 4: Rs232 Output, serial data Pin 5: Rs232Input, serial data Pin 6: System GND Pin 7: Not Used Pin 8: System GND...

  • Page 81: Connection Details

    Connection details Video Out BNC Connector—System output in video format. Output is in RS170 (NTSC). Optional PAL output is available on special order. This video output is used for displaying inspection results of the T-DAR system in real time and processed video.

  • Page 82: Input 3&9

    Connectors. Use the specific section of this user’s guide for application details on available inputs, outputs and configuration of this port. Input 3&9 The portal contact is used to monitor the status of the door position switch. This should be a dedicated switch, and may require the installation of a double pole/double throw door position switch.
  • Page 83 Pins Portal 1 Encoder Bl/Wh Blue CAT-5 Encoder Gr/Wh Blue CAT-5 Ground Or,Or/Wh,Gr,Bl Blue CAT-5 -Encoder +12 Volt Br,Br/Wh Blue CAT-5 +Encoder Figure 38–pin out for encoder Cat-5 Figure 39 –Position of Encoder on door...

  • Page 84: T-Dar Dual Digital Inputs

    T-DAR Dual Digital Inputs The T-DAR uses dual polarity opto-isolators on all digital inputs. All inputs can be used as either sinking or sourcing inputs. Note: as there is a single common for the entire set of inputs, all inputs must be configured as either sourcing or sinking.
  • Page 85 MK200B Stereo Camera Mounting Kit - Installation Guide Overview This mounting kit is designed to install a T-DAR stereo head camera safely and attractively in a standard acoustical tile ceiling. Figure 1 – Completed assembly Getting Started Refer to your T-DAR installation and operation manual for recommended camera locations with respect to the entry door.
  • Page 86 Required Hardware Each mounting kit should contain the following: • (1) Lower mounting plate (two round holes) • (1) Upper mounting plate (large rectangular opening) • (2) Caddy® 512 snap-on fixture hangers • (4) Clips and spacers • (8) ¼-20 x 1.5" flat socket cap screws •...
  • Page 87 With the tile out of the ceiling grid, snap the fixture hangers over the grid "T" section as shown. Figure 3 – Snap on fixture hanger detail Adjust the clips on the upper plate to match the fixture hanger orientation. Note that the clips can swivel on both the fixture hanger and the upper plate to match the ceiling grid layout.

  • Page 89: Known Issues And Installation Tips

    Known Issues and installation Tips When using an electric solenoid locks, reverse voltage diodes across the solenoid terminals must be used to reduce voltage feedback to the system. When mounting the TDAR on the wall or cabinet, ensure that there is at least 6 inches between each TDAR or any other physical barrier for proper ventilation.

  • Page 90: Linelock Input

    LINELOCK INPUT Required if Low Frequency Fluorescent Lighting is utilized in the installation The T-DAR™ system requires an input of low voltage AC from a source that also supplies the lighting for the installation (as shown in the diagram below). This low voltage (6 to 30VAC) AC signal is required to allow the cameras to be in sync with the low frequency fluorescent lighting.

  • Page 91: Index

    Models ..........8 Display ........... 52 Monitor Tab ........52 Door Control ........61 Mounting....10, 11, 15, 85-88 Door Position Switch ....35 Newton Security Inc......1 Drawing a Box ....... 59 NTSC .........29, 81 EEPROM......... 49 OFF to ON Response.....76 Enclosure ........11 OFF Voltage Level......76...
  • Page 92 Piggybacking........2 Storage Temp .........16 Portal Common......95 S-Video ...........94 Portal Reset ........91 Switch Setup ........58 Power ..........16 T1010..........13 Programming Annunciator... 79 T2010..........13 Relay Connection ......43 Tailgating........3, 68 Relay Portal ....... 91, 92, 94 TCP/IP ..........45 Relay Spare........92 T-DAR..........3...

This manual is also suitable for:

T2010

Table of Contents