Pioneer DEH-2850MP Installation Manual

DEH-2850MP
DEH-1850
This product conforms to new cord colors.
Los colores de los cables de este producto se
conforman con un nuevo código de colores.
As cores dos fios deste produto seguem um novo
padrão de cores.
Æ...b¹b'« „öÝô« Ê« uë lÄ "UN'« «c¼ r− M¹
Printed in Thailand
<CRD4030-A/N> ES <KSNZX> <05G00000>
5
60°
Fig. 1 Fig. 3
± qJAë ≥ qJAë
6
2
1
182
53
3
4
Fig. 2 Fig. 4
¥ qJAë
≤ qJAë
9
7 5
11
10
Fig. 5 Fig. 7
∑ qJAë
µ qJAë
8
Fig. 6
∂ qJAë
Installation <ENGLISH>
Note: Removing the Unit (Fig. 3) (Fig. 4)
• Before making a final installation of the unit,
5. Frame
temporarily connect the wiring to confirm that
To remove the frame, extend top and bottom of
the connections are correct and the system works
the frame outwards in order to unlock it. (When
properly.
reattaching the frame, point the side with a
• Use only the parts included with the unit to
groove downwards and attach it.)
ensure proper installation. The use of unautho-
• It becomes easy to remove the frame if the front
rized parts can cause malfunctions.
panel is released.
• Consult with your nearest dealer if installation
6. Insert the supplied extraction keys into the unit,
requires the drilling of holes or other modifica-
as shown in the figure, until they click into place.
tions of the vehicle.
Keeping the keys pressed against the sides of the
• Install the unit where it does not get in the dri-
unit, pull the unit out.
ver's way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.
DIN Rear-mount
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot
— for instance, near a heater outlet.
Installation using the screw holes on
• If installation angle exceeds 60° from horizontal,
the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)
the unit might not give its optimum performance.
(Fig. 1)
1. Remove the frame.
• When installing, to ensure proper heat dispersal
7. Frame
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose To remove the frame, extend top and bottom of
cables so they are not blocking the vents. the frame outwards in order to unlock it. (When
reattaching the frame, point the side with a
groove downwards and attach it.)
DIN Front/Rear-mount
• It becomes easy to remove the frame if the front
panel is released.
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or 2. Fastening the unit to the factory
"Rear" (DIN Rear-mount installation, utilizing
radio mounting bracket.
threaded screw holes at the sides of unit chassis).
8. Select a position where the screw holes of the
For details, refer to the following illustrated
bracket and the screw holes of the head unit
installation methods.
become aligned (are fitted), and tighten the
screws at 2 places on each side. Use either truss
screws (5 × 8 mm) or flush surface screws
DIN Front-mount
(5 × 9 mm), depending on the shape of the screw
holes in the bracket.
Installation with the rubber bush (Fig. 2)
9. Screw
1. Dashboard
10. Factory radio mounting bracket
2. Holder
11. Dashboard or Console
After inserting the holder into the dashboard,
then select the appropriate tabs according to the
thickness of the dashboard material and bend
them.
(Install as firmly as possible using the top and
bottom tabs. To secure, bend the tabs 90
degrees.)
3. Rubber bush
4. Screw