Table of Contents
Advertisement
Quick Links
NOTE:
Please read all
instructions carefully
before using this product
Table of Content
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MWB-345
Retain This
Manual for
Reference
02-25-05
OWNER'S
MANUAL
MARCY
MWB-345 BENCH
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
IMPEX INC.
Advertisement
Table of Contents
Related Manuals for Impex MARCY MWB-345
Summary of Contents for Impex MARCY MWB-345
- Page 1 Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MWB-345 Retain This Manual for Reference 02-25-05 OWNER'S MANUAL MARCY MWB-345 BENCH IMPEX INC. 14777 Don Julian Rd., City of Industry, CA 91746 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com info@impex-fitness.com...
-
Page 2: Table Of Contents
WARRANTY...…. ORDERING PARTS...…. BEFORE YOU BEGIN Thank you for selecting the MARCY MWB-345 BENCH by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 3: Hardware Pack
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. -
Page 5: Assembly Instruction
ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (SEE Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#15) in the Mid-span. Secure them with two M10 x 2 3/8”... - Page 6 STEP 2 (SEE DIAGRAM 2) A.) Connect the Front Stabilizer (#42) to the Main Seat Support (#52). Secure them with two M10 x ¾” Hex Bolts (#46), four DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support (#52) to the open bracket on the Cross Brace (#15). Secure them with two M10 x 2 3/8”...
- Page 7 STEP 3 (SEE DIAGRAM 3) A.) Attach the Leg Developer (#38) onto the bracket on the Front Stabilizer (#42). Secure it with an Allen Socket Axle (#44) and Allen Socket Screw (#45). B.) Insert two Foam Roll Tubes (#39) halfway through the hole on the Leg Developer. Push four Foam Rolls (#37) onto the Tube from both ends.
- Page 8 STEP 4 (SEE DIAGRAM 4) A.) Attach the hole-side of the Backrest Supports (#16) onto both ends of the Pivot on the Main Seat Support (#52). The other side rest against the Backrest Adjustment Bar (#10). B.) Place the Backrest Board (#18) onto the Backrest Supports (#16). Secure it with four M6 x 1 3/8”...
- Page 9 STEP 5 (SEE Diagram 5) A.) Attach the ball end of the Cable (#27) to the Pulley (#28). Place the Pulley in the open slot on the Lat Bar Frame (#31). Secure it with one M10 x 2 1/8” Hex Bolt (#32), two Pulley Bushings (#29), two B.) Slide the Weight Holder (#33) onto the Lat Bar Frame from the bottom.
-
Page 11: Parts List
PARTS LIST KEY NO. DESCRIPTION Rear Upright Beam M10 x 2 3/8” Hex Bolt ¾” Washer M10 Aircraft Nut 1 5/8” x 3 1/8” Square End Cap 1 ¼” Square End Cap Bracket Short Lock Pin 1” Round End Cap Backrest Adjustment Bar Bar Catch Panel ¾”... -
Page 12: Impex Inc
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.