Do you have a question about the Bistro and is the answer not in the manual?
Questions and answers
Gordon
June 2, 2025
when switch is on and the throttle switch is turned to operate there is a clicking sound and the motor will not run replaced the fuse with the same results with the sweet pea model
1 comments:
Mr. Anderson
June 2, 2025
A clicking sound and failure of the motor to run when the throttle switch is activated could be caused by a burned-out fuse or motor/electrical switch damage. An overload condition, such as a rider being too heavy or a hill being too steep, can cause the motor to overheat and the fuse to blow.
Page 1
Read and understand this entire manual before riding! DO NOT RETURN TO STORE! NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Item Number: Bistro 15130638 Bella 15130662 Betty 15130661...
Do not ride the Pocket Mod in mud, ice, puddles or riders are able to safely and responsibly use this product. Razor recommends water. Avoid excessive speeds that can be associated with downhill rides.
8mm and 10mm wrenches (Not Included) (Not included) (Not Included) Need Help? Visit our web site for updates and a list of authorized service centers at www.razor.com or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
ASSEMBLY AND SET-UP q Attaching the Handlebars Tools required: One (1) 6mm Allen wrench. Remove plastic protector Tighten down the hexagonal and insert handlebar assembly bolt with the 6mm hexagonal key through front fairing and into fork wrench. until it stops. Raise to desired height keeping the handlebars and fairing aligned within the red arrows of the safety zone.
ASSEMBLY AND SET-UP q Inflating the Tires Note: The pressurized air supplies Tires are inflated when shipped, but they invariably lose some pressure between the point of manufacturing and your purchase. found at gasoline stations are designed to inflate high-volume automobile tires.
Do not disable or replace this lever with anything other than a genuine Razor replacement part. To adjust the play, thread the If brake is too tight or has too brake lever adjuster on the hand...
REPAIR AND MAINTENANCE Tighten the brake housing Re-attach the chain guard. Test anchor securely. ride and readjust as needed. q Replacing the Fuse Tools required: Phillips screwdriver Turn power switch OFF. WARNING: To prevent shock, please follow the instructions accordingly and do not skip or combine any steps.
Refer to the disposal instructions at Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an left. If acid comes into contact with environmentally sound manner. Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not skin or eyes, flush with cool water dispose of a lead-acid battery in your regular household trash.
Correct the conditions that caused the fuse to burn out and avoid repeatedly burning out fuse. Motor or electrical switch damage Contact your local Razor authorized service center for diagnosis and repair. Undercharged battery Charge the battery. A new battery should have been charged for at least...
POCKET MOD PARTS Keep your Pocket Mod running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) Footplate Front Wheel Complete Handlebar Grip (Right/Left)
Page 11
SB 1918 (CALIFORNIA) DECLARATION YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
Little Red 15130658 purchased. Need Help? Visit our web site for updates and a list of authorized service centers at www.razor.com or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time. Patent Pending Printed in China for:...
Need help?
Do you have a question about the Bistro and is the answer not in the manual?
Questions and answers
when switch is on and the throttle switch is turned to operate there is a clicking sound and the motor will not run replaced the fuse with the same results with the sweet pea model
A clicking sound and failure of the motor to run when the throttle switch is activated could be caused by a burned-out fuse or motor/electrical switch damage. An overload condition, such as a rider being too heavy or a hill being too steep, can cause the motor to overheat and the fuse to blow.
This answer is automatically generated