TESTO CN45R4 Instruction Manual
  1. Manuals
  2. Brands
  3. TESTO Manuals
  4. Power Tool
  5. CN45R4
  6. Instruction manual
TESTO CN45R4 Instruction Manual

TESTO CN45R4 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Instruction Manual

BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL, TO UNDERSTAND
AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. IF YOU HAVE ANY QUESTIONS,
CONTACT WITH OUR REPRESENTATIVES OR DISTRIBUTOR.
COIL NAILER
WARNING
CN45R4, CN2150C, CN2565S1, CN3383C1, CN3390C1
CN2360P, CN2970P, CN2970M, CN3383P, CN3390P

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CN45R4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for TESTO CN45R4

  • Page 1: Instruction Manual

    BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL, TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. IF YOU HAVE ANY QUESTIONS, CONTACT WITH OUR REPRESENTATIVES OR DISTRIBUTOR. CN45R4, CN2150C, CN2565S1, CN3383C1, CN3390C1 CN2360P, CN2970P, CN2970M, CN3383P, CN3390P...

  • Page 2: Table Of Contents

    CONTENTS PAGE TOOL SPECIFICATIONS NAIL SPECIFICATIONS EXTERNAL TOOL PARTS SAFETY INSTRUCTIONS LUBRICATION AND MAINTENANCE ACTUATING TOOL OPERATING THE TOOL 8-10 TROUBLESHOOTING GUIDE...

  • Page 3: Tool Specifications

    CONSTRUCTION COIL NAILER TOOL SPECIFICATIONS Model No. CN45R4 CN2150C CN2565S1 CN3383C1 CN3390C1 Height 11.1” (281mm) 10.9” (278mm) 12.6” (320mm) 13.4” (340mm) 13.9” (354mm) Width 4.4” (112mm) 4.3” (110mm) 5.1” (130mm) 5.4” (136mm) 5.4” (136mm) Length 9.5” (241mm) 9.5” (240mm) 10.7” (273mm) 13.3”...

  • Page 4: Tool Specifications

    INDUSTRIAL COIL NAILER TOOL SPECIFICATIONS Model No. CN2360P CN2970P CN2970M CN3383P CN3390P Height 11.9” (301mm) 13” (330mm) 12.1” (308mm) 13.4” (340mm) 13.9” (354mm) Width 5.4” (136mm) 5” (128mm) 5” (128mm) 5.4” (136mm) 5.4” (136mm) Length 11.1” (281mm) 12” (306mm) 12.1” (308mm) 13.3”...

  • Page 5: Safety Instructions

    SAFETY INSTRUCTIONS WARNING: Read this manual and understand all instructions before operating the tool. If you have any questions, please contact with our authorized representatives. The operator and all persons in the general area should wear safety glasses to guard against flying fasteners and debris, which could cause severe eye injury.
  • Page 6 Coupling must be used which removed all pressure from the tool when the coupling joint is disconnected. Never use tool that is leaking air, has damaged or missing parts. Never point the tools at co-workers or yourself at any time . Never carry the tool from place to place holding the trigger.
  • Page 7 Never use the body of the tool or top cap as a hammer, always use the tool for its intended use. Do not discharge fasteners into concrete, stone, or any material too hard for the fastener to penetrate. Do not drive fasteners close to the edge of the work surface. The workpiece maysplit causing the fastener to ricochet, fly free or hit someone.

  • Page 8: Lubrication And Maintenance

    LUBRICATION AND MAINTENANCE Use Pneumatic tool oil or a non-detergent oil. Do not use detergent oil or additives as they will damage o-rings and rubber parts. Use a filter and regulator when possible Add pneumatic oil into the air inlet twice daily. (Depending on frequency of tool use) Wipe tool clean daily and inspect for wear.

  • Page 9: Operating The Tool

    Switchable Trigger (BlackColor) 1. Push the button forward at both side of trigger to set up for bump fire. 2. Push the button backward at both side of trigger to set up for sequential fire. Forward Backward Bump Sequential OPERATING THE TOOL Read Safety Instruction section of this manual.
  • Page 10 How to adjust nail holder. ● For CN45R4, CN2150C, CN2565S1, CN3383C1, CN3390C1, CN2360P, CN2970P tool The nail holder can be adjusted up and down per nail’s length. To change setting, pull the post up directly and twist to the correct step.
  • Page 11 " Do not use on scaffoldings, ladders" , and shall not be used for specific application: when changing one driving location to another involves the use of scaffoldings, stairs, ladders, or ladder alike constructions, e.g. roof laths. closing boxes or crates. fitting transportation safety systems e.g.

  • Page 12: Troubleshooting Guide

    TROUBLESHOOTING GUIDE WARNING: Disconnect air from tool before all repairs! Stop using the tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a qualified person or an authorized service center only.

This manual is also suitable for:

Cn2150cCn2565s1Cn3383c1Cn3390c1Cn2360pCn2970p ... Show all

Table of Contents