Table of Contents
Related Manuals for Charnwood LS5T37A
Summary of Contents for Charnwood LS5T37A
-
Page 1: Operating Instructions
370MM 5 TON LOG SPLITTER OPERATING INSTRUCTIONS MODEL: LS5T37A Charnwood, Cedar Court, Walker Road, Bardon, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email; sales@charnwood.net website; www.charnwood.net... -
Page 2: Warning Symbols
WARNING SYMBOLS WARNING! Standard graphic symbols are used on all machines in order to ensure complete safety of all parts of the log splitter. As these symbols are very important, read the information below attentively. Conforms to relevant safety standards. It is obligatory to read the machine’s use and maintenance manual in full before using the machine. - Page 3 Dumping of used oil in the environment is forbidden. The oil must be disposed of according to current legislation in the country where this operation is carried out. Danger of cutting or crushing of the hand: never touch hazardous areas while the wedge is moving.
-
Page 4: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS IMPORTANT! When using electrical tools, the following safety instructions should be observed to prevent the risk of electric shock, personal injury and fire. Read and observe these instructions carefully before using the tool. 1. Keep work area clean 5. - Page 5 recommended when working outdoors. Form the habit of checking to see that Wear protection hair covering to contain keys and adjusting wrenches are removed long hair. from the tool before switching it on. 9. Use safety glasses 17. Avoid unintentional starting Also use a dust mask during pulverulent Do not carry plugged-in tools with finger operations and wear ear protection.
-
Page 6: Special Safety Instructions For Log Splitter
SPECIAL SAFETY INSTRUCTIONS FOR LOG SPLITTER 1. The log splitter must always be used by one operator only. 2. Nobody must be allowed to use the log splitter unless they have read the instruction manual and have been instructed in the regulations to follow for correct and safe use. Operators must receive necessary training and instructions. -
Page 7: Technical Specifications
20. Check that the electric circuit is adequately protected and that it corresponds with the power, voltage and frequency of the motor, check that there is a ground connection, and a regulation differential switch upstream. Check on the functioning of the machine. 21. - Page 8 mains. 3. This machine can be switched to the WARNING! Connect the main leads to a standard 240V±10% (50Hz±1Hz) electrical single-phase network (240V/50Hz), if you supply which has protection devices of are in doubt about the earth of the electricity provisions, consult an electrician under-voltage, over-voltage, over-current as well as a residual current device (RCD) first.
-
Page 9: Loose Parts List
Note: If any parts are damaged or missing, do the switch on until the damaged or missing not attempt to plug in the power cord and turn parts are obtained and are installed correctly. LOOSE PARTS LIST Check all loose parts from the box with the list below. Assemble according to the instruction on the following pages. -
Page 10: Application Conditions
FEATURES 1. Before attempting to use, familiarize yourself with all the operating features and safety requirements of your log splitter. 1. Wedge 2. Oil tank 3. Supporting leg 4. Rolling wheel 5. Motor w/push switch & circuit breaker 6. Log pusher 7. -
Page 11: Assembly And Operation
ASSEMBLY AND OPERATION Warning! For your own safety, do not connect the log splitter to the power source until the machine is completely assembled and you read and understand the entire instruction manual. Warning! For your own safety, never forget to bolt the support leg to the log splitter, lift the log splitter by the handles at both ends and place it on a 60-75cm high, stable, flat and level work surface. - Page 12 Assemble the support leg and carry handle. c) Assembly the carry handle on the support a) Make the log splitter vertically (Fig. 7) leg by two bolts ,elastic washers and flat washers. (Fig.9) 3. Assemble the wheels a) Make the log splitter horizontally, then put the two wheels into the wheel bracket.
- Page 13 LITITING SCREW (14) IN FIG. 17! Operation Max pressure was set before the log splitter ex work and the max pressure limiting screw is tightened to ensure the Warning! log splitter works under pressure no more Before operating the log splitter, the Bleed than 4 tons.
- Page 14 damage the machine. Do not attempt to split 2 pieces of logs at the same time. One of them may fly up and hit you. After this time interval, the oil under pressure will be overheated and the machine could be damaged.
-
Page 15: Troubleshooting
3. Turn the log splitter on the motor side over an 3 liters capacity container to drain the Periodically check oil level to ensure it is hydraulic oil off. between 2 grooves around the dipstick. 4. Turn the log splitter on the support leg Upon lower oil level, oil refilling is required. -
Page 16: Exploded View
Air sealed in hydraulic system while Loosen bleed screw by some operating rotations before operating the log splitter Oil leaks around Bleed screw is not tightened before Tight the bleed screw up before cylinder ram or moving the log splitter moving the log splitter from other Oil drain bolt with dipstick is not tight. -
Page 17: Parts List
PARTS LIST Part Part Description Q’ty Description Q’ty Motor Fixing bracket Rubber pad Elastic pin 3×20 Nut M8 Flat washer 5 Pin φ2.5×4 Elastic washer 5 Sealing bush Screw M5×16 Casting iron plate Front cover Steel ring 10 Sealing ring Steel ballφ2.5 O-ring48.7×3.55G Gear shaft...