SmartPool Sunheater S425 Installation & Operation Manual

Swimming pool solar heating systems
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

INSTALLATION &
OPERATION MANUAL
How Solar Pool Heating Works
• Using your pool pump, water
is automatically pumped
through the solar collectors.
• The water is then heated by the
sun as it moves through the
collectors.
• The heated water is returned
back to the pool, through
your return lines.
• You enjoy your own
heated pool with no
fuel costs.
PLEASE READ THIS MANUAL CAREFULLY. YOUR ENJOYMENT OF YOUR SOLAR HEATED POOL
AND YOUR WARRANTY ARE AFFECTED BY HOW YOUR SOLAR HEATING SYSTEM IS INSTALLED
CAUTION:
a) Solar collectors are often installed on the roofs of buildings. Unless you are very familiar with working
on roofs and have the proper ladders and safety equipment for such work, you should hire someone with
the necessary experience to do the installation. Failure to observe safe practices on a roof or other elevated
structure may result in falling, leading to serious injury to you.
b) When installing collectors on the ground, do not build a rack support that could allow children access
into the pool.
for Aboveground Pools
Product Number S425
Why Solar Heat Works Best
Collector Cross Section
• Water is heated as it moves through the many
tubes in the solar collectors.
• Tube and web design traps heat and catches
light as the sun moves across the sky.
• Tough polypropylene material won't rust, corrode
or scale. Plus, the collector is reversible.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sunheater S425 and is the answer not in the manual?

Questions and answers

Summary of Contents for SmartPool Sunheater S425

  • Page 1 Aboveground Pools Product Number S425 INSTALLATION & OPERATION MANUAL How Solar Pool Heating Works Why Solar Heat Works Best • Using your pool pump, water is automatically pumped through the solar collectors. Collector Cross Section • The water is then heated by the sun as it moves through the collectors.
  • Page 2 Each solar box (2 Collectors) will weigh approximately 80 lbs. (36 kg) when filled with water. There is very little additional load on your roof since the weight is dispersed over a large area. Order Guide for S425 Pool Sizes...
  • Page 3 Product # S425 Kit Components Item # Description SCPNL220 2’ x 20’ (610 cm x 6.1 m) Polypropylene Solar Collectors SC600HSE 6’ (1.829 m) Flex Hoses Limted Warranty SK-41 System Kit for S425 69003 Elbow Connectors 69002 PVC End Caps 1 1/2” (3.81 cm) FPT SC150CLMP 1 1/2”...
  • Page 4: System Layout

    SYSTEM LAYOUT Single Box Required: • Flathead screwdriver or 5/16" (8 mm) nut driver. • If solar collectors are placed farther than 6 ft. (1.829 m) from your pool equipment, you will need to purchase sufficient hose or pipe to connect the collectors to your pool equipment. Elbow Connector White End Cap Labels...
  • Page 5: Operation And Maintenance

    OPERATION & MAINTENANCE Operation 1. The collectors should feel cool to the touch when the sun is shinning on them and water is passing through. This means that the heat is being transferred to the water. 2. The water returning to your pool will be a few degrees (3-5degrees F/ 2-3 degrees C) warmer than the pool itself. This is the most efficient way to heat a large body of water like a pool.
  • Page 7 Système de chauffe-eau solaire pour piscines hors sol de pièce : S425 Guide d’installation et de fonctionnement Le principe du chauffage solaire L’vantage du système SunHeater • Grâce à la pompe de votre piscine, l'eau circule automatiquement dans le collecteur solaire.
  • Page 8 Pour poser le système solaire sur un toit ou un support, vous aurez besoin d’un nécessaire de pose SK-43 (un de ces nécessaires pouvant fixer jusqu’à deux capteurs S425). Dans les endroits très venteux, nous recommandons un nécessaire SK-34 grand vent pour chaque capteur.
  • Page 9 Produit n° S425 – Composants du nécessaire Nécessaire Qté Article n° Description Capteurs solaires en polypropylène de 2 pi x 20 pi SCPNL220 SC600HSE Flexibles plastique de 6 pi énoncé de garantie SK-41 Nécessaire pour S425 69003 Coudes 69002 Embouts PVC filetage femelle de 1,5  po (3,81 cm)
  • Page 10 SCHÈMA DE MONTAGE DU SYSTÈME SYSTÈME SIMPLE Matériel nécessaire : • Tournevis à lame plate ou tourne-écrou de 5/16 po (8 mm). • Si les capteurs solaires sont placés à plus de six pieds de l’équipement de la piscine, vous aurez besoin d’un flexible ou d’un tuyau d’une longueur suffisante pour relier les capteurs à...
  • Page 11: Fonctionnement Et Entretien

    FONCTIONNEMENT ET ENTRETIEN Fonctionnement 1. Les capteurs doivent être frais au toucher lorsque le soleil brille et que l’eau circule. Cela signifie que la chaleur est transférée dans l’eau. 2. L’eau qui retourne à la piscine sera plus chaude de quelques degrés (3 à 5 ˚F/ 2 à 3 ˚C) que celle de la piscine. C’est le moyen le plus efficace de chauffer un grand volume d’eau comme celui d’une piscine.
  • Page 13 SISTEMAS DE CALEFACCIÓN SOLAR DE PISCINAS PARA PISCINAS ELEVADAS Número de Producto S425 MANUAL DE INSTALACIÓN Y OPERACIÓN Cómo funciona la calefacción solar de piscinas Por qué la calefacción solar funciona mejor • Utilizando la bomba de su piscina, se bombea agua automáticamente a través...
  • Page 14 Cada caja solar (2 colectores) pesará aproximadamente 80 libras (36 kg) cuando esté llena de agua. La carga adicional para el techo es bastante pequeña, ya que el peso se distribuye sobre una superficie grande. Guía de Pedido para S425 Dimensiones de la piscina Número de...
  • Page 15 Capteurs solaires en polypropylène de 2 pi x 20 pi SCPNL220 SC600HSE Flexibles plastique de 6 pi Declaración de garantía Kit de sistema para el Producto N o. S425 SK-41 69003 Conectores “codo” 69002 Tapones terminales de PVC de 1.5” (3.81 cm) c/rosca hembra SC150CLMP Abrazaderas de manguera 35-51 de 1.5”...
  • Page 16: Disposición Del Sistema

    DISPOSICIÓN DEL SISTEMA Sistema sencillo Se requiere: • Un desatornillador de cabeza plana o una llave para tuercas de 5/16 de pulgada (3.81 cm) • Si se instalan los colectores solares a más de 6’ (1.829 m) de distancia del equipo de su piscina, necesitará comprar una cantidad suficiente de manguera o tubería para conectar los colectores al equipo de su piscina.
  • Page 17: Operación Y Mantenimiento

    OPERACIÓN Y MANTENIMIENTO Operación 1. El colector debe estar frío al tacto cuando el sol da sobre el colector y el agua está pasando por él. Esto significa que se está transfiriendo el calor al agua. 2. El agua que vuelve a su piscina estará unos grados (de 3 a 5 ˚F/ 2 a 3 ˚C) más caliente que la propia piscina.
  • Page 20 Lakewood, NJ 08701 • www.smartpool.com S425 82205...

Table of Contents