Do you have a question about the PZ-008 and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for POWERZONE PZ-008
Page 1
PZ-008 DYNAMIC 1500 FPV Assembly and Operating Manual Main specification: SPECIFICATION Wing span : 1480mm(58.3in) Length : 992mm(39.0in) Weight : 690 g(24.4oz.) Total surface area: approx. 24dm2 Total surface area loading: approx. 28.8g / dm2 Electronic systems: Servo: 4*9g,1.5kg/cm,0.18s/60 Battery : 11.1v 1300MAh(20C) Li-polymer battery...
Page 2
DYNAMIC 1500 FPV Dear customer, Congratulations on your choice of a factory-assembled model aircraft from the POWERZONE and thank you for placing your trust in us. Very little preparation work is required to get this model ready to fly. To operate your new model safely it is important to that you read through all of the instructions and safety information included with your model, before you fly it for the first time.
DYNAMIC 1500 FPV Foam safe epoxy is recommended and available from most reputable model retail shops. Make sure that all parts are “dry” before applying glue. Trial-fit all parts “dry” before applying glue. Follow the recommended curing time suggested by the glue manufacturer. Allow the glue to fully cure (harden) to the point where the joint can be placed under stress.
DYNAMIC 1500 FPV Illustration of Assembly Fig. 1 Fig. 2-Connect the push rods to the - Fix the Main wing control rods with aileron servo arm screw. ( ( ( ( The first hole) ) ) ) Fig.4 - plug the main wing to the Fig.
Page 6
DYNAMIC 1500 FPV Fig.7 Fig.8 - Fix the horizontal stabilizers control -The photo shows Install the horizontal rods with screws as shown in the photo. stabilizers on the fuselage. Fig.9 Fig.10 - The photo shows Install the vertical - Fix the control rods with screws as stabilizers on the fuselage.
Page 7
DYNAMIC 1500 FPV Fig.14 - Connect the electronic speed controller Fig.13 - The photo shows the propeller is and servos to the receiver .Refer to the radio installed in the fuselage. instructions for the correct channel sockets and servo lead polarity . Fig.16 Fig.17 - Photo shows the battery is installed...
Page 9
DYNAMIC 1500 FPV Checking Ailerons and Elevators elevator aileron vertical -Check that the control surfaces respond to the appropriate movements of the transmitter sticks. If not, swap over the connectors at the receiver. -Check the neutral position of the control surfaces; you may need to screw the clevises in or out to correct any discrepancy.
Page 10
DYNAMIC 1500 FPV place the flight battery in its compartment, without connecting.ark the Centre of Gravity (CG) on both sides of th efuselage; the position is shown in the photo.Support the model at the marked points and allow it to hang eely.
Page 11
DYNAMIC 1500 FPV PZ-004 Spare Parts PZ1280-1 PZ1280-2 PZ1280-3 PZ1280-4 Fuselage Main Wing Vertical Stabilizer Horizontal tail PZ1280-5 PZ1280-6 PZ1280-7 PZ1280-8 Motor Transmitter servos PZ1280-9 Li-Po Battery PZ1280-10 PZ1280-11 PZ1280-12 CarbonFilber Cockpit-canopy Control rods Tube PZ1280-13 PZ1280-14 PZ1280-15 PZ1280-16 Balance Propeller V-Lead Motor mount...
Page 12
DYNAMIC 1500 FPV Yancheng Powerzone Model Co., Ltd. NO.6 Golden Batan Road, Batan Town, Binhai County ,Yancheng City, Jiangsu Province ,224500 China. Powerzone.model@gmail.com Phone: +(86)515-89198008 Fax: +(86)515-89198700 www.ycpoerzone.com - 12 -...
Need help?
Do you have a question about the PZ-008 and is the answer not in the manual?
Questions and answers