Advertisement
Operation Guide 4319
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
• Auto Receive
With auto receive, the watch receives the time calibration signal automatically up to
six times a day. When any auto receive is successful, the remaining auto receive
operations are not performed. For more information, see "About Auto Receive".
• Manual Receive
Manual receive lets you start time calibration signal reception with the press of a
button. For more information, see "To perform manual receive".
Important!
• When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 o'clock side facing towards a window.
Make sure there are no metal objects nearby.
• Make sure the watch is facing the right way.
• Proper signal reception can be difficult or even impossible under the conditions listed
below.
Inside or
Inside a
Near
among
vehicle
household
buildings
appliances,
office
equipment,
or a mobile
phone
• Signal reception normally is better at night than during the day.
• Time calibration signal reception takes from two to seven minutes, but in some
cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
Reception Ranges
U.S. Signal
2,000 miles
(3,000 kilometers)
600 miles
(1,000 kilometers)
Fort Collins
Signal reception may not be possible at the distances noted below during certain
times of the year or day. Radio interference may also cause problems with reception.
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
• Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
• Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
• See the information under "Signal Reception Troubleshooting" if you experience
problems with time calibration signal reception.
About Auto Receive
With auto receive, the watch receives the time calibration signal automatically up to six
times a day. When any auto receive is successful, the remaining auto receive
operations are not performed. The start times of the auto receive operations depend
on the current Home City and DST settings.
Home City:
HKG
,
SEL
,
TYO
,
HNL
,
ANC
Standard Time Auto Receive Times:
Midnight, 1:00 a.m., 2:00 a.m., 3:00 a.m., 4:00 a.m., 5:00 a.m.
DST Auto Receive Times:
Midnight, 1:00 a.m., 2:00 a.m., 3:00 a.m., 4:00 a.m., 5:00 a.m.
Note
• Auto receive is performed only if the watch is in the Timekeeping Mode or World
Time Mode when one of the calibration times is reached. It is not performed if a
calibration time is reached while an alarm is sounding, or while you are configuring
settings (while settings are flashing on the display).
• When a reception time is reached, the second hand stops at 12 o'clock and
reception starts. The second hand remains stopped until reception is complete.
• Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
• When auto receive is turned on, the watch receives the calibration signal for two to
seven minutes everyday when the time in the Timekeeping Mode reaches each of
the calibration times. Do not perform any button operation within seven minutes
before or after any one of the calibration times. Doing so can interfere with correct
calibration.
• Remember that reception of the calibration signal depends on the time kept in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the
Timekeeping Mode time actually is the correct time.
12 o'clock
or
Near a
Near high-
Among or
construction
tension
behind
site, airport, or
power lines
mountains
other sources
of electrical
noise
Japan Signals
500 kilometers
Fukushima
1,000 kilometers
500 kilometers
Fukuoka/Saga
1,000 kilometers
,
LAX
,
DEN
,
CHI
,
NYC
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received. For
best reception, keep the watch in a location where signal strength is strongest.
Receiving indicator
Weak
(Level 1)
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
• Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal reception.
• The Level 4 receiving indicator indicates that at least one of the auto calibration
signal receive operations was successful. Note, however, that the Level 4 receiving
indicator is cleared from the display at the first auto receive time of the following day.
• The Level 4 receiving indicator appears on the Timekeeping Mode's Receiving
Indicator and Seconds Count screen only. The Level 4 receiving indicator is not
displayed if signal reception was unsuccessful or after manual adjustment of the
current time setting.
To perform manual receive
1. Place the watch on a stable surface so its 12 o'clock
Receiving indicator
side is facing towards a window.
2. In the Timekeeping Mode, hold down D for about two
seconds until the watch beeps.
3. Release D and RC flashes to indicate that signal
reception has started.
• When reception starts, the second hand will move at
high speed to the 12 o'clock position where it will stop
until reception is complete.
• Time calibration signal reception normally takes from two to seven minutes, but in
some cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
• After signal reception is complete, the display of the watch changes to the last signal
screen.
Note
• To interrupt reception and return to the Timekeeping Mode, press D.
• If reception is unsuccessful, the message
one or two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the last signal or
screen by pressing D.
To turn auto receive on and off
1. In the Timekeeping Mode, press D to display the Last
Signal screen.
On/Off status
2. Hold down A until the current auto receive setting (
or
) starts to flash. This is the setting screen.
OF
• The second hand will move at high speed to the 12
o'clock position, where it will stop.
• Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press D to toggle auto receive on (
4. Press A to exit the setting screen.
• The second hand will advance at high speed to the correct position in accordance
with the digital time seconds count, and resume normal movement from there.
• For information about city codes that support signal reception, see "To set your
Home City"
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
Problem
Probable Cause
• The watch is not in the Timekeeping
Cannot perform
manual receive.
Mode.
• Your current Home City is not one of the
following city codes: HNL, ANC, LAX,
DEN, CHI, NYC, HKG, SEL or TYO.
• You changed the time setting manually.
Auto receive is
• The watch was not in the Timekeeping
turned on, but
the Level 4
or World Time Mode, or you were
receiving
performing some button operation
indicator does
during auto receive.
• Even if reception is successful, the
not appear on
the Timekeeping
Level 4 receiving indicator disappears
Mode display.
each day when the first auto receive
operation of the day is performed.
• Time data (hour, minutes, seconds) only
was received during the last reception.
The Level 4 receiving indicator appears
only when time data and date data
(year, month, day) are both received.
• If the time is one hour off, the DST
Time setting is
incorrect
setting may be incorrect.
• The Home City code setting is not
following signal
reception.
correct for the area where you are using
the watch.
• For further information, see "Important!" under "Time Calibration Signal Reception"
and "Radio-controlled Timekeeping Precautions".
Strong
(Level 4)
ERR
appears on the display for about
ERR
screen to the normal timekeeping
ON
) and off (
).
ON
OF
What you should do
• Enter the Timekeeping Mode
and try again.
• Select HNL, ANC, LAX,
DEN, CHI, NYC, HKG, SEL
or TYO as your Home City.
• Perform manual receive or
wait until the next auto
receive is performed.
• Check that the watch is in a
location where it can receive
the signal.
• Change the DST setting to
Auto DST.
• Select the correct Home City
code.
2
Advertisement
