Table of Contents
Advertisement
RECTANGULAR GAS FIREPIT
RECTANGULAR CALENTADOR DE
OWNER'S MANUAL / MANUAL DEL PROPIETARIO
GUARDE ESTE MANUAL PARA REFERENCIA FUTURA
NOTICE TO INSTALLER:
LEAVE THESE INSTRUCTIONS
WITH THE FIREPIT OWNER FOR
FUTURE REFERENCE.
AVISO PARA EL
INSTALADOR:
ENTREGUE ESTAS
INSTRUCCIONES AL
PROPIETARIO DE EL
CALENTADOR DE FUEGO PARA
REFERENCIA FUTURA.
FUEGO A GAS
ASSEMBLY AND OPERATING INSTRUCTIONS
INSTRUCCIONES DE ARMADO Y OPERACIÓN
SAVE THIS MANUAL FOR FUTURE REFERENCE
HAZARDOUS EXPLOSION MAY RESULT IF THESE WARNINGS AND INSTRUCTIONS
ARE IGNORED. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS
MANUAL TO AVOID PERSONAL INJURY, INCLUDING DEATH OR PROPERTY DAMAGE.
SE PUEDE PRODUCIR UNA EXPLOSIÓN PELIGROSA SI SE HACE CASO OMISO A
ESTAS ADVERTENCIAS E INSTRUCCIONES. LEA Y SIGA TODAS LAS ADVERTENCIAS
E INSTRUCCIONES EN ESTE MANUAL PARA EVITAR LESIONES PERSONALES,
FOR OUTDOOR USE ONLY
SOLO PARA USO AL AIRE LIBRE
WARNING/ADVERTENCIA
INCLUSO LA MUERTE, O LOS DAÑOS MATERIALES.
Advertisement
Table of Contents
Summary of Contents for Gharmglow RECTANGULAR GAS FIREPIT
- Page 1 RECTANGULAR GAS FIREPIT RECTANGULAR CALENTADOR DE FUEGO A GAS OWNER’S MANUAL / MANUAL DEL PROPIETARIO ASSEMBLY AND OPERATING INSTRUCTIONS INSTRUCCIONES DE ARMADO Y OPERACIÓN SAVE THIS MANUAL FOR FUTURE REFERENCE GUARDE ESTE MANUAL PARA REFERENCIA FUTURA WARNING/ADVERTENCIA NOTICE TO INSTALLER:...
- Page 2 IMPORTANT SAFETY WARNINGS WE WANT YOU TO ASSEMBLE AND USE YOUR FIREPIT AS SAFELY AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR FIREPIT. WHEN YOU SEE THE SAFETY ALERT SYMBOL PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS! READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND OPERATING YOUR FIREPIT.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Important Safety Information ........3 Firepit Specifications . -
Page 4: Important Safety Information
IMPORTANT SAFETY INFORMATION WARNING • The installation must conform with local codes or, in the absences of local codes, with the National Fuel Code, ANSI Z223.1. • The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with The National Electrical Code, ANSI/NFPA70. -
Page 5: Firepit Specifications
RECTANGULAR GAS FIREPIT SPECIFICATIONS: Product name Rectangular Gas Firepit Model No. 832-7000-S Rated Heat Output 40,000 BTU/HR Fuel Propane-LPG Gas Supply 20 lb. LP-gas cylinder Manifold Pressure 11 inches water column Orifice Size (diameter) 1.96(0~+0.02)mm Gas Supply Pressure Maximum 250 PSI... - Page 6 WARNING • Turn off the cylinder valve when your firepit is not in use. • Handle the tank with care. • Always secure the cylinder in an upright position. • Never connect an unregulated LP gas cylinder to your firepit. •...
- Page 7 WARNING FILLING THE LP GAS CYLINDER: • Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder. • New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank. •...
- Page 8 WARNING • Never use your firepit without leak testing all gas connections and hoses. See the section on "Leak Testing" in this manual for proper procedures. WARNING The pressure regulator and hose assembly supplied with your gas firepit must be used. •...
-
Page 9: Leak Testing
DANGER LEAK TESTING: To prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. •... -
Page 10: Pre-Start Check List
6. Check each place listed (A– K) for growing bubbles which indicates a leak. 7. Turn off gas supply at cylinder valve. 8. Turn on the control knob to release gas pressure in hose. 9. Turn the control knob to "OFF" position. 10. -
Page 11: Lighting Instructions
WARNING Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any of the warnings and instructions contained in the preceding sections of this manual. WARNING LIGHTING INSTRUCTIONS: Follow the instructions exactly. 1. REMOVE THE FIREPIT COVER before attempting to light the burner so that gas fumes do not accumulate inside the firepit. -
Page 12: Storage And Maintenance
TURNING OFF THE GAS FIREPIT: 1. Turn off the cylinder valve. 2. Turn burner control knob to the "OFF" position. Note: Turn off LP cylinder first to prevent gas from being left in the system under pressure. CAUTION: • The cylinder valve should always be in the off, or closed, position when the firepit is not in use. -
Page 13: Trouble Shooting
TROUBLE SHOOTING PROBLEM OBSERVED POSSIBLE CAUSE CORRECTIVE MEASURES Gas odor Gas leakage Check all gas connections Delayed ignition Low gas pressure Check gas supply pressure Clogged or dirty burner ports Clean burner ports-see manual section Bad battery Change battery Incorrect burner flame Incorrect gas supply or pressure Check gas supply pressure Clogged or dirty burner ports... -
Page 14: Parts List And Assembly Instructions
PARTS BAG CONTENTS Make sure you have all items listed under PARTS LIST and PARTS BAG CONTENTS before you begin the installation process. Your Parts Bag will include: Qty. Qty. 34 M6 X 14mm Bolts M5 Nut M5 Washer M4 X 10mm Bolts M6 Washers AA /1.5V Alkaline Battery M4 X 30mm Bolts... -
Page 15: Assembly Instructions
BEFORE ASSEMBLING OR OPERATING YOUR FIREPIT. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT. The following tools are required to assemble this Charmglow ® Rectangular Gas Firepit: • Flathead Screwdriver • Hex Nut Wrench PARTS LIST: Cover Handle... - Page 16 Choose a good, cleared assembly area and get a friend to help you to unpack and set up your firepit. Front & Back Table Panels CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary. Step 1 Left & Right Attach the four table panels by Table Panels using eight M6 x14mm bolts and...
- Page 17 Step 5 Connect the drawer panel with the tank holder support by using four M6 x 14mm bolts. Attach both strengthener supports to the drawer panel and tank holder support by using four M6 x 14mm bolts. Insert cylinder clamp screw as shown. Cylinder Clamp Screw Note: With the help of a friend, turn...
- Page 18 Step 7 Align tank holder support runners with the sliding tracks on the front and rear panels. Insert runners fully until locked into position. Step 8 Place the burner assembly on the table with the control panel facing the front panel door, attach it by using four M4 x 30mm bolts.
- Page 19 Step 9 Insert cover handle through firepit cover and secure it to cover by using one M5 washer and M5 nut. Step 10 Firepit Cover Place firepit grate directly over burner assembly. Lava Rocks Firepit Grate Step 11 Arrange lava rocks on firepit grate.
- Page 20 ® Charmglow Rectangular Gas Firepit (Assembled)