Page 3
WELCOME TO THE EASIER WAY TO ACCESS YOUR HOME...
Page 4
This guide will show you how to install your G+ Home Port. WHaT’s IN your G+ HoME PorT BoX? G+ HOME PORT MOUNTING BRACKET Take care! Electricity kills. switches, power outlets and other fixed wire products must be installed by a licensed electrical contractor or similarly qualified person.
Overview The G+ Home Port is an electrically powered device used within the G+ Access System to enable non G+ Systems to control G+ Devices. The G+ Home Port is wired to a non G+ control system. The G+ Home Port controls G+ Devices via a RF, (Radio Frequency), link. aPPlICaTIoNs G+ Devices a G+ Home Port can control include: • G+ Locksets...
NoN G+ CoNTrol sysTEMs Examples of suitable systems that could activate a G+ Home Port include: • Home automation systems • Building access system A suitable system is one that activates the G+ Home Port by: • Voltage Free Contact / Dry contact for > 100ms • Voltage Input –...
Communication Overview G+ Locksets Up to 3 x groups of G+ Smart Boxes / Receives G+ Enabled Gliderol commands from Garage Door the G+ Home Port Receives commands from the G+ Home Port Command Inputs to G+ Home Port Non G+ Controlled System section 1 Communication Overview...
Installation loCaTIoN The G+ Home Port is to be installed in a secure, dry environment out of direct sunlight. NoTE: The installation location, (walls / materials), can affect the operation distance between the G+ Home Port and a G+ lockset / G+ smart Box. This should be checked by the installer prior to installation.
Wiring Instructions Guidelines TaKE CarE - ElECTrICITy KIlls! switches, power outlets and other fixed wired products must be installed by a licensed electrical contractor or similarly qualified person. NoTE: The installer should consider strain relief for all cables. INPuT (from controlling devices) NoTE: The installer is responsible for ensuring the compatibility of systems being connected to the G+ Home Port.
Typical wiring for Voltage Free / Dry contacts Input 3 Input 2 Input 1 Typical wiring for Voltage Input Input 3 Input 2 Input 1 PoWEr This appliance shall only be supplied at safety extra low voltage corresponding to the marking on the appliance. Connection of 12/24 V aC/DC NoTE: This appliance is only to be used with the power supply unit provided with the appliance.
Setup ProGraMMING Programming G+ Home Port to a G+ Lockset • Press the G+ Home Port Lock Teach button until the teach light is on. • Press the G+ Lockset Teach button, (via paper clip or similar), until the Teach Confirmation Sound is heard – approx 3 seconds. • Wait for Lockset to emit a single beep confirming successful recognition of the G+ Home Port.
Page 19
Removing G+ Devices from a G+ Home Port • Press the Remove Button on the G+ Home Port until the light is illuminated. • Place the G+ Device into teach mode and wait until the Teach Confirmation is heard / seen. • Wait for G+ Device to end its Teach session.
Page 22
916.365 MHz & 918 MHz ENVIroNMENTal sPECIFICaTIoN Operating temperature range -10°C to 50°C Storage temperature range -10°C to 60°C FrEquENTly asKED quEsTIoNs Refer to the Gainsborough website for frequently asked questions. www.gainsboroughhardware.com.au CoNTaCT Customer service 13 14 18 section 3 General Specifications...
Page 23
The availability of products set out in this document is not guaranteed and Gainsborough Hardware reserves the right to alter, amend or delete any part of this document without prior notice. This disclaimer is subject to any contrary legislative provisions.
Page 24
Gainsborough Hardware Industries Limited Hotline 13 14 18 Head Office 31–33 Alfred Street Blackburn, VIC 3130 PO Box 330, Blackburn VIC Telephone 03 9877 1555 Admin & Export Fax +61 (0)3 9894 1599 Email sales@gainsboroughhardware.com.au www.gainsboroughhardware.com.au Suite 1B, 433 Logan Rd 12 Juna Drv 31–33 Alfred St...