Summary of Contents for Hypertec PCI 10/100 TX
-
Page 1: User Guide
HyperNet PCI 10/100 TX HYNEC52001 USER GUIDE Information in this document is subject to change without notice. All rights reserved. All brand names are registered trademarks of their respective companies. - Page 2 HYPERTEC. HYPERTEC reserves the right to make modifications to the product without notification. Hypertec is a trademark and the Hypertec logo is a registered trademark of HYPERTEC. All other brand and product names included herein may be trademarks of the respective companies.
- Page 3 The HyperNet PCI 10/100 Adapter series is highly integrated and cost-effective single-chip adapter range that provides 32-bit performance, PCI bus master capability, and full compliance with Fast Ethernet 100Base-TX specifications. It also supports full- duplex operation, making possible 200Mbps of bandwidth with no additional cost, when connected to an appropriate switch.
- Page 4 Features PCI 32-Bit bus-mastering architecture speeds data transfers between your PC and the network, without burdening the PC’s processor Autonegotiation, sensing and switching between 10Mbps and 100Mbps operation Full Duplex capabilities - Independent receive and transmit circuits allow for full duplex operation at both 10Mbps and 100Mbps, giving the Card a maximum throughput of 200Mbps A Single RJ-45 female connector supports both 10Mbps and 100Mbps operation...
-
Page 5: Static Electricity Warning
If you do not have each of these items, contact your supplier before proceeding further. Static Electricity Warning Static electricity is accumulated naturally in the human body, and can be discharged through electrical components by touching them. This shock can potentially cause permanent internal damage to the component. - Page 6 accidental damage. Remove your computer's cover (refer to your computer owner's manual). Select an available PCI expansion slot which supports Bus Master mode, and remove slot cover. Make a note of the slot number (if one is printed on the motherboard, next to this slot).
- Page 7 Configuring the PCI 10/100 Adapter PCI Computer with PnP Auto-Configuration Before installing your Hypertec PCI 10/100 Adapter, try to establish whether your PC has PCI PnP Auto configuration. In most cases, the PCI computer will be configured automatically by the system's BIOS during boot up. The BIOS automatically assigns the I/O base address and IRQ to the card for proper operation.
- Page 8 Checking card operation The Adapter provides two LEDs to indicate operation: FDX (Full Duplex) LK/ACT (Link/Activity) LI N K /A C T (A cti vi ty) FD X (Ful l -D upl ex) Figure 2. PCI 10/100Base series Adapter LED indicators Steady Green Light indicates the connection to a full duplex switch port.
- Page 9 For more details of the loading procedure for software drivers, please execute the HELP8139.EXE program. If at any time during installation you experience difficulties, please contact Hypertec Technical Support on +44 1488 686844 (01488 686844 in the UK).
- Page 10 The setup program can view current configuration and run diagnostics on the HyperNet PCI 10/100 series Adapters. This testing includes three separate procedures: View Current Configuration Setup New Configuration Run diagnostics Menu Adapter cannot connect to the network Make sure that the cable is installed properly. The network cable must be securely attached to all connections.
- Page 11 1 2 3 4 5 6 7 8 Figure A-1 show the PCI 10/100BaseTX RJ-45 Connector Pin Assignments Note: The Pin assignments are identical for 10Base-T and 100Base-TX, by using UTP cable. Network cabling In Fast Ethernet 100Base-TX, the cable, quality, distance, and connectors must comply with the EIA/TIA 568 “Commercial Building Wiring Standard”.
- Page 13 Length - 125.4mm Height - 42.3mm LED Indicators: Full Duplex, Link/Activity Operating Temperature: 0°-55°C (32°F-131°F) Operating Humidity: 0% - 90% non-condensing Storage: -20°C-65°C (-4°F–149°F) Ethernet Protocols: IEEE 802.3U (Fast Ethernet, 100Base-TX) IEEE 802.3 (Ethernet, 10Base-T) Data Transfer Rate: 100 or 10 Mbit/sec 200 or 20Mbit/sec Full Duplex Connector: Unshielded RJ-45 female connector.
- Page 14 The liability of Hypertec is limited to the repair or replacement of the product with a functionally equivalent or better product. Hypertec is not liable for any accidental, general, special, exemplary or consequential damages resulting from any product failure, even if Hypertec has been advised of the possibility of such damages.
Need help?
Do you have a question about the PCI 10/100 TX and is the answer not in the manual?
Questions and answers