Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ICP Electronics WS-855
- Page 1 WS-855 15” LCD 10-slot Workstation User Manual...
-
Page 2: Copyright Notice
Copyright Notice This document and product is copyrighted, May 1999, by ICP Electronics Inc. All rights are reserved. No part of this manual may be reproduced, copied, or translated without prior notice to ICP Electronics Inc. The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products. -
Page 3: Table Of Contents
Table of Contents Chapter 1 Product Information 1.1 General Information 1.2 Product Specifications 1.3 Mechanical Dimension 1.4 Front Accessible CD-ROM, 3.5" FDD, 3.5” HDD 1.5 Sealed-membrane accessible keypad Chapter 2 System Setup 2.1 Adding cards 2.2 Disk Drives Installation 2.3 Power Supply Installation 2.4 The Fan Installation 2.5 Panel Mounting 2.6 Rack Mounting... -
Page 4: Chapter 1 Product Information
LCD Interface Direct connect to ICP main board’s LVDS-02 Module Versatile Passive Backplane WS-855 can be equipped with PCI-10S (standard), BP-10S, IP-10S or PX-10S 10-slot backplane. Sealed-membrane accessible keypad The sealed-membrane keypad has 59 data keys including 10 function keys to allow users enter data directly. -
Page 5: Product Specifications
1.2 Product Specifications Front Panel: Aluminum meets NEMA 4 or IP65. 8U Height, Rack-mount or panel-mount with front LCD on/off switch. Disk Drive Bay: Support one 5.25" Drive CD-ROM, one 3.5" FDD and one 3.5" HDD. LCD interface: 44-pin connector to JUKI series CPU board or PLC-655 LCD control card. - Page 6 1.3 Dimensions The following diagram indicates the dimensions of WS-855. 413. 4...
-
Page 7: Front Accessible Cd-Rom, 3.5" Fdd, 3.5" Hdd
1.4 Front Accessible CD-ROM, 3.5" FDD WS-855 workstation is equipped with one CD-ROM and 3.5" FDD that can be accessible by opening the front lockable drive door as the following diagram shown. Power ON/OFF switch, Brightness adjustment and Display ON/OFF switch are also accessible by opening this front lockable drive door. -
Page 8: Chapter 2 System Setup
Users also can attach the external keyboard through a connector on the front panel of WS-855. A built-in controller will merge the signals from the membrane keypad and general keyboard into one signal, which acts as a standard IBM PC/AT keyboard. -
Page 9: Adding Cards
The WS-855 15" TFT LCD 10-slot workstation is very easy to set up for operation. All you have to do is to open the back cover, install your CPU card, display control card, hard disk drive and other I/O cards required by your application, and you are ready to mount into a 19"... -
Page 10: Power Supply Installation
which should be installed from the rear of chassis. Users ought to take advantages of clamps to fix CD-ROM, HDD and HDD as the diagrams shown. 2.3 Power Supply Installation ACE-925A, industrial power supply is equipped at the rear of this workstation. It is fastened with power supply bracket by 4 screws as the diagram below shown. - Page 11 ACE-925A 85-265VAC 0.3A 0.5A 204,100 2.4 Cooling Fan Installation WS-855 is equipped with a 12 cm ball bearing cooling fan with removable fan filter by the side of workstation. The following diagram shows the details of fan and its accessories.
-
Page 12: Panel Mounting
2.5 Panel Mounting WS-855 can be mounted within a panel as the diagram below shown. Please make sure the dimensions of the case within panel aperture so that your screw holes line up with the mounting bolts on the flange of WS-855. -
Page 13: Rack Mounting
2.6 Rack Mounting WS-855 not only be mounted within a panel but also can be mounted in a 19" Rack. The following diagram shows how to mount WS-855 into the 19" Rack. -
Page 14: Chapter 3 Maintenance
Chapter 3 Maintenance There are some essential parts you need to know during the operation for the purpose of maintenance or upgrading. -
Page 15: Power Supply
3.2 Cooling Fan WS-855 is equipped with 12 cm cooling fan with removable fan filter by the side of workstation. Please refer to the diagram of section 2.4. You have to open the chassis and unfasten the four bolt kits to take fan out for maintenance. - Page 16 Appendix B Keypad Keypad Decoder...
- Page 17 TO FUNCTION KEYPAD TO KEYBOARD TO CPU CARD TO KEYBOARD KBD-01 TO TEXT KEYPAD l Scan code and ASCII code index for 10 function keys expansion Scan code ASCII code Character (Hex) NULL NULL NULL NULL NULL NULL NULL NULL NULL NULL Appendix C Display Interface...
- Page 18 LCD - 07 To:Touch (control board) LCD-07 LVDS Receiver LVDS-02 LVDS Transmitter ITEM Description Part No. Qty. REMARK 1 LCD-07 0169-LCD07-000 2 VR/RV16YN/10SB103/1K 1310-421001 3 TOGGLE 6007-20005-01 SW/PT-S1-T1-B1-M1-S-E 4 DF14-20S-1.25C M toM/50cm 8202-1007301 5 SW/VR LINE/35cm 8202-1013401 6 5P FOR BKI 8390D/28cm 8202-1013601 7 TOUCH PANEL/25cm 8202-1013701...
- Page 19 RA0+ RB0- RB0+ RC0- RC0+ RCLK0- RCLK0+ RA1- RA1+ RB1- RB1+ RC1- RC1+ RCLK1- RCLK1+ CN2:BACKLIGHT INVERTER IN (FROM TRANSMITTER SIDE) +12V +12V ENBKL CN3:LCD CONNECTOR (TO FLAT PANEL DISPLAY) PIN NO Function PIN NO Function FLM(VSYNC) LP(HSYNC) M(DE)
- Page 20 SHFCLKA SHFCLKB *VCC:LCD POWER (+5V) CN4 :BACKLIGHT INVERTER CONNECTOR (TO INVERTER) Vin(+12V) ON/OFF Potentio GND Pin5 series a Resistor R4 to GND Reserved for potentiometer GND CN5:BACKLIGHT SWITCH & BRIGHTNESS VR PIN NO Function ENBKL To CN4 Pin2 VR or Vadj Potentio GND Pin4 series a Resistor R4 to GND 1-2 On: BKI operated...
- Page 21 +12V RS232 9584A To Touch Panel...