Page 1
Televisión a color Capítulo 1: Ajustes generales Instrucciones de seguridad Reemplazo y montaje del ensamble de TRC Ajustes de los componentes del tubo de imagen 50HX70 Reemplazo del TRC Modo de servicio Ajustes eléctricos Ajustes de convergencia Alineación de pantalla y espejo Revisión de circuitos...
CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous 2. This receiver is equipped with a Fail Safe (FS) circuit which X-RAY RADIATION.
CRT ASSEMBLY REPLACEMENT AND MOUNTING CAUTION : DO NOT LOOSEN THE HEX HEAD BOLTS WITH SPRINGS (12 PCS), BECAUSE THOSE ARE FOR SEALING OF CRT COOLANT. Attention Serviceman The Hex Head Bolts with Springs. (see sketch) used on CRT assembly, 8 o’clock are “NOT”...
TO REMOVE CRT (Same procedure for R, G, B) 1. Remove CRT DRIVE Board, S. V. M. COIL and DEF. YOKE from CRT. 2. Remove Lens Assembly. 3. Detach CRT Anode Cap from CRT. 4. Remove CRT Assembly from CRT Mounting. Anode Cap CRT REPLACEMENT (Same procedure for R, G, B) Reverse the removal procedures except the followings.
WARNING : BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRE- CAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL. PICTURE TUBE COMPONENTS ADJUSTMENT Pole 4, 6 magnet Pole 2 magnet DESCRIPTION OF NECK COMPONENTS 2. Select adjustment mode (see page 10). 3.
Page 8
R, G, B FOCUS ADJUSTMENT TILT ADJUSTMENT 1. Before adjusting the R, G, B FOCUS, remove the 4 screws Rotate R, G, B deflection yoke so that picture becomes hori- of Lens Assembly which is fixed on the CRT Assembly. zon, then fasten screw.
Page 9
LOCATION OF SCREEN AND FOCUS VR’S SCREEN VR FOCUS VR – 8 –...
REPLACEMENT OF THE CRT Service parts are provided for each R, G and B. The contents of the parts are as follows. 50HX70 23005770 23005771 23003382 ↑ ↑ 55HX70 23005777 HITACHI 55H70 23005723 23005808 23005724 61HX70 23007215 23007216 23007217 61H70...
SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press MUTE button once 2) Press MUTE button 3) While pressing the MUTE button, on Remote Control. again to keep pressing. press MENU button on TV set. MUTE (Service mode display) 2. DISPLAYING THE ADJUSTMENT MENU 1) Press MENU button on TV.
Page 12
4. SELECTING THE ADJUSTING ITEMS 1)Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING & ADJUSTING DATA on page 18) 5.
ELECTRICAL ADJUSTMENT ITEM ADJUSTMENT PROCEDURE VERTICAL POSITION (VCEN) 1. Call up the adjustment mode display, then select item VCEN. 2. Press the VOLUME s or t button to get the voltage 0 ±10 mV. 3. Measuring the terminals voltage are TP-V and TP-G on SIGNAL Board. SUB-BRIGHTNESS 1.
Page 14
ITEM ADJUSTMENT PROCEDURE HEIGHT 1. Call up the adjustment mode display, then select the item HIT. (HIT) 2. Press the VOLUME s or t button to get the picture so the top of raster begins * Except 16:9 mode to lack. 3.
CONVERGENCE ADJUSTMENT Adjust convergence from center to circumference in order. 1. Select the adjustment mode following the steps on page 10. RCUT KEY FUNCTION IN THE CONVERGENCE ADJUSTMENT: Up : 2 button Selet Green color: 3 button Left : 4 button 2.
Page 16
NOTES In many cases, color misconvergence may be corrected by returning HIT and WID data in main deflection side to initial adjusting values. Following cases will surely require readjustment of convergence. CRT REPLACEMENT When CRT is replaced, main deflection readjustment and color matching are required. Perform following procedures.
SCREEN AND MIRROR ALIGNMENTS ASSEMBLING OF MOUNTING OF FRONT SCREEN FRONT SCREEN Fresnel sheet 5 screws Lenticular shield 3 screws FRONT Protect shield (for 50”) 3 screws Lenticular sheet Protect shield 3 screws FRONT Fresnel sheet Stick cotton cloth tape Label with part Label with part number...
CIRCUIT CHECKS HIGH VOLTAGE CHECK FS CIRCUIT CHECK CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on The Fail Safe (FS) circuit check is indispensable for the final this chassis. Checking should be done following check in servicing. Checking should be done following the the steps below.
CHAPTER 2 SPECIFIC INFORMATIONS SETTING & ADJUSTING DATA SAFETY INSTRUCTIONS 40~61" HIGH VOLTAGE AT ZERO BEAM: 31.5 kV MAX HIGH VOLTAGE: 32.6 kV Table-1 SERVICE MODE ADJUSTING ITEMS AND DATA IN THE SERVICE MODE: Item Name of adjustment Preset Date Item Name of adjustment Preset...
LOCATION OF CONTROLS (Representative : 61HX70) TV front Remote sensor (Behind the screen) Behind the door Power Indicator T Sst MENU EXIT TV/VIDEO DEMO POWER Video Audio inputs POWER VOLUMET S TV/VIDEO (Video3) CHANNEL st DEMO MENU EXIT TV rear ANT (75Ω) ANT-1 AUDIO CENTER...
Remote Control SLEEP LIGHT POWER POWER LIGHT SLEEP CABLE/SAT MOVIE SPORTS NEWS MODE switch AUDIO1 Set to “TV” to control the TV. SERVICES LIST AUDIO2 MODE Channel Number PIC SIZE 100/ – ACTION FAVORITE INFO MENU/ENTER MENU/ stT S/FAV T S ENTER CHANNEL s/t VOLUME s/t...
PROGRAMMING CHANNEL MEMORY The channel memory is the list of TV channel numbers the TV tunes in when you press the CHANNEL s or t button. First, use the TV/CABLE and CH PROGRAM functions to preset all active channels in your area automatically. If necessary, arrange the preset channels with the ADD/ERASE functions so that you can tune into only desired channels.
Page 23
THIS PAGE IS INTENTIONALLY LEFT BLANK. – 22 –...
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. • The PC board assembly with mark is no longer available after the end of the production. Models : 50HX70/55HX70/61HX70/55H70/61H70 Capacitors ..... CD Ceramic Disk : Plastic Film : Electrolytic Resistors ....
SPECIFICATIONS (Representative: 61HX70) TELEVISION SYSTEM NTSC standard CHANNEL COVERAGE VHF: 2 through 13 UHF: 14 through 69 Cable TV: Mid band (A-8 through A-1, A through I) Super band (J through W) Hyper band (AA through ZZ, AAA, BBB) Ultra band (65 through 94, 100 through 125) POWER SOURCE 120 V AC, 60 Hz POWER CONSUMPTION...