Please read this manual carefully before using this product and save this manual for future use. Note • In this manual, most illustrations shown are based on the KX-UTG200. Outline This manual briefly describes basic information about the installation of the unit. Related Documentation Operating Instructions Describes information about the installation and operation of the unit.
The Bluetooth word mark and logos are registered trademarks owned by ® the Bluetooth SIG, Inc. and any use of such marks by Panasonic System Communications Company of North America is under license. • All other trademarks identified herein are the property of their respective owners.
Page 3
For Your Safety WARNING General Safety Do not disassemble this unit. Dangerous electrical shock could result. The unit must only be disassembled and repaired by qualified service technicians. Never attempt to insert wires, pins, etc. into the vents or other holes of this unit.
Page 4
For Your Safety If damage to the unit exposes any internal parts, immediately disconnect the cable or cord. If the power is supplied from the network to the SIP Phone [Power-over-Ethernet], disconnect the Ethernet cables. Otherwise, disconnect the AC adaptor cord. Then return this unit to an authorized service center.
For Your Safety Placement Care should be taken so that objects do not fall onto, and liquids are not spilled into, the unit. Do not subject this unit to excessive smoke, dust, moisture, mechanical vibration, shock, or direct sunlight. Do not place heavy objects on top of this unit. Place this unit on a flat surface.
• External parts (the handset, cords, etc.) of the unit are not interchangeable. Only use Panasonic brand parts. Important Safety Instructions When using this unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: Do not use the unit near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
Accessory Information Accessory Information Included Accessories* Handset (1) Handset Cord (1) [Part No.] [Part No.] 95.1204T00 371.00447.005 Stand (1) Ethernet cable (1) [Part No.] [Part No.] 467.00209.005 371.00473.005 *1 For extra orders for the accessories, call toll-free: 1-800-332-5368. Note • The illustrations may differ from the appearance of the actual product.
Location of Controls Location of Controls Front View For KX-UTG200: EF G H I J K L MN O P Q R For KX-UTG300: F G H IJ K L MN OP Q R...
Page 9
Keeps the handset stable when the unit is mounted on a wall. B LCD (Liquid Crystal Display) KX-UTG200 is equipped with a 3.5-inch color LCD and LCD backlight. KX-UTG300 is equipped with a 5.0-inch color LCD touch screen and LCD backlight.
Page 10
Installation and Setup Q REDIAL Used to redial the last dialed number. R HOLD Used to put a call on hold. Right Side View (for KX-UTG300) A Add-on Key Module Slot Cover Remove the Add-on key module slot cover when connecting an Add-on key module to the unit.
Installation and Setup Installation and Setup Notice • Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. Attaching the Stand Notice • If you place the display face down when you attach the stand, be sure to place a soft cloth under the display.
Page 12
Installation and Setup Connections Optional AC adaptor To a switching hub (Ethernet cable) To a PC (Ethernet cable) To an EHS To a handset jack (handset) Clamp To a headset AC adaptor Headset Handset CAUTION Optional AC Adaptor • Use the following AC adaptor: –...
Page 13
(KX-UTG300 only) ® For up-to-date information about headsets that have been tested with this unit, refer to the following web site: http://www.panasonic.com/sip When connecting the Ethernet cable • Connect the Ethernet cable as shown in the following illustration. Incorrect...
Page 14
Installation and Setup Installing the KX-UTA336 (KX-UTG300 only) The optional KX-UTA336 allows 36 additional flexible buttons (3 pages of 12) to be used with the KX-UTG300. These flexible buttons are used to make calls or receive calls, or perform a feature that has been assigned to the button. A maximum of 2 KX-UTA336 Add-on key modules can be con- nected to the KX-UTG300.
Page 15
Installation and Setup Connect the KX-UTA336 (A) to the KX-UTG300 (B) by inserting the connec- tor (C) into the Add-on key module slot (D). Secure the KX-UTA336 to the KX-UTG300 by inserting the 2 screws supplied with the KX-UTA336 into the rear of the KX-UTG300.