Advertisement
ENGLISH
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
Industry Canada Regulatory Information
CAN ICES-3 (B)/NMB-3 (B)
Avis d'Industrie Canada
CAN ICES-3 (B)/NMB-3 (B)
Step 1: Install Batteries
Your RCRHM02BR universal remote requires 2 new AAA alkaline batteries (sold
separately).
To install the batteries:
1. Turn the unit over, and remove the battery compartment cover.
2. Insert the batteries, matching the batteries to the (+) and (-) marks inside
the battery case.
Battery Precautions:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargable (nickel-cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in
accordance with Local and National Regulations.
Step 2: Program the Remote
To use this universal remote with your home entertainment system, first you need
to program it to control your devices. There are three ways you can program the
universal remote to operate your devices:
• The Auto Code Search goes automatically through all the codes for the device
you're trying to control. It's the easiest method, but it can sometimes take
longer than some of the other programming methods.
• The Direct Code Entry lets you enter a code from the accompanying code
list for your brand of device. It's not as easy as the other methods, but it's
potentially the fastest method.
• The Manual Code Search lets you manually go through all the codes for the
device you're trying to control.
ENGLISH
2
Auto Code Search
The Auto Code Search goes automatically through all the codes for the device
you're trying to control. When you find the one that operates your device, you can
stop the search and store that code.
1.
Manually turn on the component you want to
program the remote to operate.
2.
Press and hold the CODE SEARCH key until the
indicator light turns on.
3.
Press the component key you want to program—
TV or SAT·CBL·DTC. The indicator light blinks
once and remains lit.
Important: Find the ENTER key on your remote (don't
press it yet). You will need to press this key quickly in step
5 below.
4.
Point the remote directly at the front panel of the
device you want to control. Press the POWER
key and wait for the indicator light to blink. Each
time the indicator light blinks, the remote is testing
a code with the device. Make sure you keep the
remote pointed at the device you want to operate.
5.
As soon as the component turns off, press the
ENTER key within 4 seconds.
Note: If you wait longer than 4 seconds to press ENTER,
the remote goes to the next code—you will need to start
the code search from step 1 again.
The indicator light flashes 8 times and turns off when the
remote has searched all the codes. If this happens, try one
of the other programming methods.
6.
Test the remote with your component to make sure
you can control most of the device's functions.
If some features don't work, try the Direct Code
Entry method.
ENGLISH
3
Direct Code Entry
Direct Code Entry lets you enter a code from the code list at the end of this manual
for your brand of device. It's not as easy as the other methods, but it's potentially
the fastest method.
1.
Manually turn on the component you want to
program the remote to operate.
2.
Find the four-digit code for your brand of TV,
satellite receiver, cable box, or digital TV converter
in the code list at the end of this manual.
3.
Press and hold the CODE SEARCH key until the
indicator light turns on.
4.
Press the component key you want to program—
TV or SAT·CBL·DTC. The indicator light blinks
and then remains lit.
Note: "DTC" stands for Digital TV Converter.
5.
Enter the four-digit code, using the numeric
keypad. After the code is entered, the indicator
light turns off.
Note: If the indicator light blinks multiple times, you've
entered an invalid code. Start from step 2 again.
6.
Aim the remote at the component and
press the POWER key.
If the component turns off: The remote is
programmed to operate this component.
If the component does NOT turn off: Try the
next code for your brand.
Note: If no codes work, or if your brand is not listed, try the
Auto Code Search or Manual Code Search.
Manual Code Search
The Manual Code Search lets you go one-by-one through all the codes for the
device you're trying to control. When you find the one that operates your device,
you can stop the search and store that code.
1.
Manually turn on the component you want to
program the remote to operate.
ENGLISH
4
2
3
4
5
6
A
T
m
a
T
1
2
3
E
Hide quick links:
Advertisement
