Troubleshooting Guide; Specifications - SAFE-T-ALERT 70-742 User Manual

MEMORY FEATURE – This alarm has a Peak Level Memory feature
that remembers the approximate amount of CO that activated it. The
memory feature does not record brief exposure to CO that would not
activate the alarm. This alarm will indicate one of four levels with chirps
and blinks with the CO LED:
To activate alarm level memory, press the TEST/RESET button for
less than 1 second.
 1 Chirp and 1 Green Blink = CO memory is clear
 2 Chirps and 2 Red = below 100 ppm
 3 Chirps and 3 Red Blinks = below 200 ppm
 4 Chirps and 4 Red Blinks = above 200 ppm
TROUBLE-SHOOTING GUIDE
Use this chart to trouble-shoot problems with this 70 Series Alarm.
PROBLEM
Green Operational LED Off
No Sound When Testing
No Red LED When Testing
Locked In Alarm
MALFUNCTION ALARM
LED Flashing Red/Green -
Beeps Every 25 Seconds
Battery Voltage is Good and
Alarm Will Not Reset
End of Life Signal
LED Flashing RED RED
GREEN GREEN Beeps
Every 25 Seconds
HOW TO TAKE CARE OF YOUR ALARM
This CO / Propane Gas Alarm is designed to be as maintenance free as
possible. To keep your alarm in good working order, you must:
TEST THE ALARM WEEKLY using the Test/Reset Button. See

the section, Test Procedure, in this manual for further information.
Test the Alarm every six months with Safe-T-Alert CO Test Gas

and with a butane lighter. See Test Procedure Section.
 VACUUM THE DUST OFF THE ALARM COVER. At least once
a year (more frequently in dusty locations), use the soft brush attachment
from your vacuum to clean the alarm covers.

CLEAN THE ALARM COVER WHEN DIRTY. Wash the alarm
cover by hand. Use a cloth dampened in clean water. Dry with a soft
.
cloth
 DO
NOT SPRAY CLEANING
DIRECTLY ONTO THE FRONT PANEL. This action may damage
the sensor, cause an alarm or cause an alarm malfunction.

OBSERVE THE COLOR OF THE INDICATOR LIGHT. At
frequent intervals and during your weekly test, check the indicator light
on the on the front panel of the alarm.

See the section, Operation, in this manual for further information.
PROCEDURES TO TAKE DURING AN ALARM
Follow the alarm procedures for your country. The emergency number
depends on your travel location.
CAUSE/SOLUTION
1.Wire Connection
2. Reversed Wiring
3. Main Power Off
4. Missing or Blown Fuse
5. Contact Customer Service
Contact Customer Service
Contact Customer Service
Contact Customer Service
1. Check Battery Voltage
2. Contact Customer Service
1. Press Test/Reset Button to
reset for 72 Hours. Can
repeat for up to 30 Days
2. Replace Alarm
AGENTS OR WAXES
PROCEDURES TO TAKE DURING GAS ALARM
1. Turn off all Gas appliances (Stove, Heater, Furnace,
Refrigerator, etc.), extinguish all flames and smoking material.
2. Press the Test/Mute switch. DO NOT DISCONNECT
POWER
3. Evacuate the RV. Make sure everyone is accounted for.
Leave the door and windows open.
4. Turn off the propane tank valve.
5. Determine and repair the source of the leak. Get professional
help if necessary. CAUTION- DO NOT RE-ENTER UNTIL
THE PROBLEM IS CORRECTED.
PROCEDURES TO TAKE
DURING A CO ALARM IN THE USA
!
WARNING
: Actuation of this device indicates the
presence of carbon monoxide (CO) or propane gases, which
can KILL YOU. If signal sounds (4 beeps and flashing or
solid red light): 1) Operate the Test/Mute button; 2) Call your
emergency local service (Phone Number _____________ )
(fire department or 911); 3) Immediately move to fresh air -
outdoors or by an open door/window. Check that all persons
are accounted for. Do not reenter the premises or move away
from the open door / window until the emergency responders
have arrived, the premises have been aired out and your alarm
remains in its normal operation. 4) After following steps 1-3,
if your alarm reactivates within a 24-hour period, repeat steps
1-3 and call a qualified appliance technician. (Phone Number
_______________) to investigate for sources of CO from fuel
burning equipment and appliances, and inspect for proper
operation of this equipment. If problems are identified during
this inspection have the equipment serviced immediately.
Note any combustion equipment not inspected by the
technician and consult the manufacturers' instructions, or
contact the manufacturer directly, for more information about
CO safety and this equipment. Make sure that the motor
vehicles are not, and have not been, operating in an attached
garage or adjacent to the residence.

SPECIFICATIONS

PROCEDURES TO TAKE
DURING A CO ALARM IN CANADA
!
WARNING: Actuation of this device indicates the
presence of carbon monoxide (CO) and propane gases which
can KILL YOU. If signal sounds (4 beeps and flashing or solid
red light: 1) Operate the Test/Mute. Immediately move to fresh
air - outdoors or by an open door/window. Check that all
persons are accounted for. Do not reenter the premises or move
away from the open door/window until the emergency
responders have arrived, the premises have been aired out, and
your alarm remains in its normal condition; 2) call your
emergency local service (telephone number _________) ( Fire
department or 911).