Level-Setting Procedure; Patchbay Description; E-Z Interface; Mic/Line Inputs On Every Channel - Mackie 1604-VLZ PRO Owner's Manual

PATCHBAY DESCRIPTION

At the risk of stating the obvious, this is
where you plug everything in: microphones,
line-level instruments and effects, and the ulti-
mate destination for your sound: a tape
recorder, PA system, etc. A few of the features
described in this section are on top of the
mixer, but most are out back on the "pod."
1604-VLZ PRO, you can patch anything almost
anywhere, with nary a care. Here's why:
• Every input and output is balanced
(except insert, phones and RCA jacks).
• Every input and output will also accept
unbalanced lines (except XLR jacks).
• Every input is designed to accept virtually
any output impedance.
• The main left and right mix outputs can
deliver 28dBu into as low as a 600 ohm load.
• All the other outputs can deliver 22dBu
into as low as a 600 ohm load.
• All the outputs are in phase with the inputs.
All we ask is that you perform the Level-Setting
Procedure
sound source. So stop worrying and start mixing!

MIC/LINE INPUTS ON EVERY CHANNEL

The original CR-1604 had six mic/line channels
and ten line-only channels. That was fine for most
applications, but live sound users were forced to
go out and buy the XLR-10 mic input add-on
module. No more. Each and every channel on the
New Improved 1604-VLZ PRO has the legendary
Mackie mic/line input circuit. It' s like getting a
free XLR-10 with your mixer!

MIC INPUTS

We use phantom-powered, balanced micro-
phone inputs just like the big studio mega-
consoles, for exactly the same reason: This
kind of circuit is excellent at rejecting hum
120 VAC 50/60 Hz 20W POWER PHANTOM MAIN OUT
1A/250V SLO-BLO ON ON BAL/UNBAL
L
MONO
R
CAUTION:
TO REDUCE THE RISK OF
FIRE REPLACE WITH SAME
TYPE FUSE AND RATING
+6
O O
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE. DEBRANCHER AVANT DE REMPLACER LE FUSIBLE UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE. DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
INSERT INSERT INSERT INSERT
16 15 14 13
LINE LINE LINE LINE
BAL BAL BAL BAL
UN- UN- UN- UN-
BAL BAL BAL BAL
MIC 16 MIC 15 MIC 14 MIC 13
10
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA • COPYRIGHT ©1998 • THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "VLZ", "XDR", AND THE "RUNNING MAN" FIGURE • US PATENT NUMBER 29/049,129

E-Z INTERFACE

Concerned about levels,
balancing, impedances, po-
larity, or other interface
goblins? Don't be. On your
every time you patch in a new
MAIN INSERT
TAPE TAPE C-R OUT SUB OUT
(TIP SEND BAL/UNBAL BAL/UNBAL
INPUT OUTPUT
RING RETURN)
L L 3
L L
R
R 4
R R
INSERT INSERT INSERT INSERT
12 11 10
LINE LINE
LINE LINE
BAL BAL BAL BAL
UN- UN- UN- UN-
BAL BAL BAL BAL
MIC 12 MIC 11 MIC 10 MIC 9
XDR TM EXTENDED DYNAMIC RANGE MIC PREAMPLIFIERS ARE PROPRIETARY TO MACKIE DESIGNS, INC.
and noise. You can plug in almost any kind of
mic that has a standard XLR-type male mic
connector. Always be sure to perform the

Level-Setting Procedure

nals are routed from these inputs:
wire your own, connect them like this:
Pin 1 = ground or shield
Pin 2 = positive (+ or hot)
Pin 3 = negative (– or cold)
Professional ribbon, dynamic, and condenser
mics will all sound excellent through these in-
puts. The 1604-VLZ PRO's mic inputs will handle
almost any kind of mic level you can toss at
them, without overloading.

PHANTOM POWER

Most condenser mics require phantom power,
where the mixer sends low-current DC voltage to
the mic's electronics through the same wires
that carry audio. The 1604-VLZ PRO's phantom
power is globally controlled by the PHANTOM
switch on the rear panel
Semipro condenser mics often have batter-
ies to accomplish the same thing. "Phantom"
owes its name to an ability to be "unseen" by
dynamic mics (Shure
stance) that don't need external power and
aren't affected by it anyway.
electronic devices into the MIC input jacks if
the phantom power is on.
AUX RETURN
BAL/UNBAL
1 4 3 2 1
L L L L
(MONO) (MONO) (MONO)
2
R R R R
INSERT INSERT INSERT INSERT
9 8 7 6
LINE LINE LINE LINE
BAL BAL BAL BAL
UN- UN- UN- UN-
BAL BAL BAL BAL
MIC 8 MIC 7 MIC 6 MIC 5
. To learn how sig-
. If you
2
SHIELD
HOT
3 1
COLD
SHIELD
1
3
COLD
2
HOT
SHIELD
1
3
COLD
2
HOT
.
® SM57/SM58, for in-
Unless you know for cer-
tain it is safe to do so,
never plug single-ended
(unbalanced) micro-
phones, instruments or
AUX SEND DIRECT OUT
BAL/UNBAL BAL/UNBAL
5 3 1 7 5 3
6 4 2 8 6 4
INSERT INSERT INSERT INSERT
5 4 3 2
LINE LINE LINE LINE
BAL BAL BAL BAL
UN- UN- UN- UN-
BAL BAL BAL BAL
MIC 4 MIC 3 MIC 2 MIC 1
1
2
1