Summary of Contents for Partner Tech International KB-78
- Page 1 KB-78 Programmable Keyboard User s Reference Manual Partner Tech International Pte Ltd. 705 Sims Drive #06-07A Shun Li Industrial Complex Singapore 387384 Tel: (65) 8469809 Fax: (65) 8461509...
- Page 2 Partner Tech International Pte Ltd. assumes no responsibility for any inaccuracies in the contents, nor for any infringements of patents or other rights of third parties which may result from its use. Partner Tech International Pte Ltd. makes no commitment to update or to keep current the information contained in this manual.
- Page 3 User s Reference Manual of KB-78 Keyboard Unpacking The KB-78 is packed in a box. After unpacking, the KB-78 unit placed it on a raised surface and carefully inspect the unit for any damage that might have occurred during shipment.
-
Page 4: Table Of Contents
User s Reference Manual of KB-78 Keyboard Table of Contents INTRODUCTION“ “ “ “ “ “ “ “ “ “ “ “ “ “ “ .“ “ .. 5 C H A P T E R 1 General Description“ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ “ . 5 Features“... -
Page 5: Introduction
Programmed keycodes are saved in the EPROM and download from the computer. Bar code interface, magnetic readers, point device and smart card are all available choices. Partner Tech International also supplies a series of smaller keyboards for applications, which require supplemental keypads and card verification. -
Page 6: Utility Support
NOTE: The following instructions will show you how to use the editor: 1. It is strictly advice that the initial programming & setup of the KB-78 keyboard and the magnetic strip reader (MSR) should be done in DOS environment (i.e. -
Page 7: Installation
NOTE: It is necessary to turn the key lock from ” OFF– position to any other position to active KB-78 after programming and powering on your computer. To use keyboard, the key lock has to operate as follows: A. Insert key at lock position 1 B. -
Page 8: Default Keyboard Layout
User s Reference Manual of KB-78 Keyboard C h a p t e r DEFAULT KEYBOARD LAYOUT 3.1 Schematic Diagram KB-78 Keyboard Default Layout Lock Back Page Space Ctrl Caps Left Right Print (left) Lock Scrn Shift Scroll Down Page... -
Page 9: Keyboard Programming
KEYBOARD PROGRAMMING NOTE: It is strictly advice that the initial programming & setup of the KB-78 keyboard and the magnetic strip reader (MSR) should be done in DOS environment (i.e. if your have Windows 95 or 98, then restart your system in MS-DOS mode and proceed with the programming). -
Page 10: How To Assign Multiple Codes To A Key
User s Reference Manual of KB-78 Keyboard 4.3 How to Assign Multiple Codes to a Key Step 11: If it is necessary to assign a combination of codes to any key, follow steps 3 & 4 and then substitute the following commands. -
Page 11: How To Define A Key With A String Of Characters
User s Reference Manual of KB-78 Keyboard 4.5 How to Define a Key with a String of Characters Follow step 3 & 4 and then substitute the following commands: Step 24: Use the arrow keys to move the highlighted bar to the "KEY STRING DEFINE–... -
Page 12: How To Save The Keyboard Layout
User s Reference Manual of KB-78 Keyboard 4.7 How to save the Keyboard Layout Step 36: To save your chosen layout Press <ALT + F>. Step 37: A pop-up menu will be displayed as follows: OPEN ALT + O SAVE... -
Page 13: How To Test Key Function
User s Reference Manual of KB-78 Keyboard Step 48: Use the arrow keys to select the "OPEN" option and press <Enter>. Step 49: A message will be displayed at the top left of the matrix as follows: FILE NAME = Step 50: Type the filename of the layout you wish to load and Press <Enter>. -
Page 14: Special Functions
User s Reference Manual of KB-78 Keyboard C h a p t e r SPECIAL FUNCTIONS The following functions are set as standard when the K78.EXE program is run. The Repeat Function is ”NOT– allowed. No Repeat Keyboard The 101-keyboard port is activated. -
Page 15: Mode Key Function
User s Reference Manual of KB-78 Keyboard This will provide repeat, no click and a delay of 30ms between character. You can ope n a program from the DOS command line by issuing the following command K78 -program = name KB-78 KEYBOARD TABLE 1 MODE &...