1
(STANDBY)
•
With the corresponding end of the mains power cord connected
to the AC mains input of the D 7050 and the plug connected to a
mains power source, press
from standby mode. The Standby indicator will turn from amber to
bright/white color. Pressing
to standby mode.
IMPORTANT NOTES ABOUT STANDBY MODE
The following conditions describe Standby Mode response with respect
to AUTO SHUTOFF as configured in the D 7050 app. Refer to section below
about "NAD D 7050 APP" for further information.
Condition 1
AUTO SHUTOFF in the D 7050 app is set to "ON"
•
D 7050 will automatically go to standby mode if there are no user
interface interaction and no active source within 30 minutes.
Condition 2
AUTO SHUTOFF in the D 7050 app is set to "OFF" or no D 7050 app is used
to control the D 7050
•
D 7050 will not go to standby mode at any time unless directly initiated
by pressing
(Standby) switch or OFF from the remote control.
•
The default setting of AUTO SHUTOFF is OFF.
2 VOLUME
•
Adjust audio level by turning clockwise or counterclockwise.
3 S (SOURCE)
•
Rotate to select desired Source.
4 DISPLAY
•
Illuminate the selected or active Source (COAXIAL1, COAXIAL2,
OPTICAL1, OPTICAL2, COMPUTER, AIRPLAY, DOCK, BT) and current
audio level.
•
Display follows the orientation of the unit - vertical or horizontal
view as shown on the front cover.
IMPORTANT NOTE
Display shall temporarily turn off if there is no user interface interaction
within 5 minutes. Restore display by sending a remote control
command or rotating any of the controls.
1
6
2
3
10
4
5
(Standby) to switch ON the D 7050
(Standby) again turns the unit back
IDENTIFICATION OF CONTROLS
7
8
9
AUDIO OUT
+12V
TRIGGER
R
L
IN
RESET
WPS/JB
LAN
COMPUTER
1
DIGITAL AUDIO INPUT
1
2
2
COAXIAL
OPTICAL
11
12
13
14
5 PHONES
•
A 3.5 mm stereo jack socket is supplied for headphone listening.
•
Specially designed low noise headphone circuitry can accommodate a
wide range of phones, even 600 Ohm studio models.
•
Ensure that the volume control is turned to minimum (fully
counterclockwise) before connecting or disconnecting
headphones. Listening at high levels can damage your hearing.
•
Inserting a headphone jack into this socket automatically switches
off the loudspeakers.
6 RESET
•
Restore factory default settings.
7 WPS/JB
•
Use to setup wireless network connection.
8 AUDIO OUT
•
These output terminals have dual function. They are used either as
PRE OUT or SUBWOOFER terminals.
•
Always turn OFF the D 7050 and associated external devices before
connecting or disconnecting anything to the AUDIO OUT sockets.
PRE OUT
•
The AUDIO OUT sockets can be used to drive an additional amplifier.
Use a dual RCA cable to connect AUDIO OUT to the corresponding
analog audio input of compatible devices such as amplifiers,
receivers or other applicable devices.
•
AUDIO OUT will be affected by the D 7050's volume control settings.
Rotate the VOLUME control to adjust the output level of the AUDIO
OUT sockets.
SUBWOOFER
•
Use a dual RCA cable to connect AUDIO OUT to the low level input
of a powered subwoofer.
•
Low frequency information up to 200Hz is sent to the connected
subwoofer via AUDIO OUT.
9 +12V TRIGGER IN
•
Connect this +12V Trigger input to the remote device's
corresponding +12V DC output jack using a mono cable with
3.5mm male plug. The controlling device must be equipped with a
+12V trigger output to use this feature.
SPEAKERS
RIGHT
LEFT
100-240V
50/60Hz
15
5