Advertisement
Quick Links
B.M.C. Audio CS2
Quick Start Guide
The CS2 is as easy to use as any amplifier: Connect the AC power, the input sources
and the speakers. Power on, select an input, adjust the volume - enjoy!
In a consistent B.M.C. system using the optical DIGM control, the amplification gain
of the CS2 will be controlled by the DAC volume control.
POWER
DIM
Dimmer
Input Indicator
Power (turn)
RIGHT SPEAKER
RIGHT CHANNEL
INPUT
XLR-1
XLR-2
RCA-1
RCA-2
RCA-3
SERIAL NO.:
AC Power Connection
‚ XLR Inputs
ƒ RCA Inputs
„ Speaker Terminals
... Optical DIGM Control Input
Never plug or unplug any cables while the CS2 is powered on!
Find a detailed user guide inside this manual.
INPUT
VOLUME
Input
DIGM display
Volume
Power Meter
CS2 STEREO POWER AMPLIFIER
OPTO CONTROL
LEFT CHANNEL
LEFT SPEAKER
LOOP
IN
OUT
INPUT
XLR-1
XLR-2
PHASE
AC POWER
50/60Hz
WEEE - Reg. - Nr.:
RCA-1
RCA-2
RCA-3
DE18339144
B.M.C. AUDIO
MADE BY B.M.C. GERMANY
mute
IN
VOL
AMP
disp
rep.
prog
check
clear
1
2
3
4
5
6
7
8
9
0
CD
+10
df
ovs
ups
DAC
IN
VOL
mute
RC-1
1311-EN
B.M.C. Audio CS2
Owner's Manual
DIM
POWER
INPUT
VOLUME
Advertisement
Summary of Contents for B.M.C. CS2
-
Page 1: Quick Start Guide
B.M.C. Audio CS2 Quick Start Guide The CS2 is as easy to use as any amplifier: Connect the AC power, the input sources and the speakers. Power on, select an input, adjust the volume - enjoy! In a consistent B.M.C. system using the optical DIGM control, the amplification gain B.M.C. -
Page 2: Table Of Contents
DIGM Volume Adjustment and Display Remote Control Troubleshooting, Maintainance, Service Important Safety Information General Safety Precautions CE / FCC declaration, Recycling Content of Packing Power Meter in Watt and dB Technical Specifications Quick Start Guide www.bmc-audio.com B.M.C. Audio GmbH info@bmc-audio.com Germany... -
Page 3: Introduction
There is still the advantage of a gain presetting by DIGM, may be for better +6 dB = fourfold the power signal/noise ratio, adjustment of channels for home cinema use, or matching the CS2 to a mixing console of a recording or mastering studio. Due to the numeric display the +10 dB = tenfold the power preference gain can be set easily again after an new amplifier power-on. -
Page 4: Front Panel Functions
Content of Packing Front Panel Functions AC Power Cable Remote Control RC1 DIGM optical waveguide Owner's Manual Please keep the packing for eventual later transportation. POWER INPUT VOLUME Advanced Functions In classical integrated amplifier mode by default all inputs are operating traditionally and are compatible to any source component. -
Page 5: Rear Panel Functions
CE / FCC Declaration, Recycling CE Declaration of Conformity B.M.C. AUDIO GmbH declares that this product is in conformance with the Low Voltage Directive 73/23/EEC and Electromagnetic Compatibility 89/336/EEC as amended by 92/31/EEC and 93/68/EEC. The conformity of this product with the regulations of Directive number 73/23/EEC (LVD) is proved by full... -
Page 6: Input Selection And Display
General Safety Precautions Input Selection and Display Select INPUT by pressing the INPUT switch on the front of the CS2, or the IN- 1. Read this owner's manual. UP/DOWN buttons of the remote control RC1, AMP section. 2. Keep the owner's manual. -
Page 7: Digm Volume Adjustment And Display
At DIGM 55 gain is so high that a full scale signal from a digital device with standard serviceable parts. Any burnt fuses inside this unit should level output (eg B.M.C. DAC1 or BDCD1) will drive AMP CS2 close to maximum, without be replaced by qualified service personnel only. Please pushing it into clipping. -
Page 8: Remote Control
B.M.C. DAC new ones of type AA Note: The CS2 has a micro-computer inside which may "hang-up" due to static discharge or other voltage sparks. In this case power off the unit, wait for about 1 BATTERIES minute and power on again.