Table of Contents
Advertisement
Quick Links
MANUFACTURING
NUMBERS:
9300300
9300302
9300304
9300306
9300308
9300309
9300320
9300321
9300322
9300324
9300330
9300331
9300332
9300334
9300336
9300340
9300341
9300342
9300344
9300350
9300351
HOT DOG CORRAL
9300352
9300356
9300374
9300380
Model HDC
Series 9300000
C
®
®
®
P/N 1010609
Rev. E
Owner
s Manual
'
Advertisement
Table of Contents
Summary of Contents for Roundup Food Equipment Division HOT DOG CORRAL HDC
- Page 1 MANUFACTURING NUMBERS: 9300300 9300302 9300304 9300306 9300308 9300309 9300320 9300321 9300322 9300324 9300330 9300331 9300332 9300334 9300336 9300340 9300341 9300342 9300344 9300350 9300351 HOT DOG CORRAL 9300352 9300356 9300374 9300380 Model HDC Series 9300000 ® ® ® P/N 1010609 Rev. E Owner s Manual ’...
-
Page 2: Table Of Contents
A.J. Antunes & Co. HOT DOG CORRAL TABLE OF CONTENTS Unpacking ..............6 Owner Information .............1 Equipment Setup ............6 General ..............1 Operation ..............8 Warranty Information ..........1 General ..............8 Service/Technical Assistance ........2 Operating Instructions ..........8 Important Safety Information ........2 Maintenance .............8 Specifications ............4 Cleaning ..............8 Electrical Ratings ............4 Inspecting and Aligning Drive Parts ......9... -
Page 3: Service/Technical Assistance
A.J. Antunes & Co. HOT DOG CORRAL OWNER INFORMATION (continued) Service/Technical Assistance Refer to the service agency directory included with your unit. If you experience any problems with the installation or Authorized Service Agency operation of your unit, contact your local Roundup Authorized Service Agency. - Page 4 A.J. Antunes & Co. HOT DOG CORRAL In addition to the warnings and cautions in this manual, - Do not modify the power supply cord plug. use the following guidelines for safe operation of the If it does not fit the outlet, have a proper unit.
-
Page 5: Specifications
A.J. Antunes & Co. HOT DOG CORRAL SPECIFICATIONS Electrical Ratings CAUTION All electrical connections must be in accordance Model Voltage Watts Amps Hertz with local electrical codes and any other applica- HDC-20 1000 50/60 ble codes. 1000 50/60 WARNING HDC-21A 1000 50/60 ELECTRICAL SHOCK HAZARD. -
Page 6: Dimensions
A.J. Antunes & Co. HOT DOG CORRAL Dimensions Model Width (A) Depth (B) Height (C) Shipping Weight HDC-20 18-3/4" 21" 8-1/2" 45 lbs. (476 mm) (533 mm) (216 mm) (20 kg) HDC-21A 22-7/8" 15-1/4" 7-1/4" 38 lbs. (581 mm) (387 mm) (184 mm) (17.2 kg) HDC-30A... -
Page 7: Installation
A.J. Antunes & Co. HOT DOG CORRAL INSTALLATION Unpacking Driver Frame 1. Remove unit and all packing materials from ship- ping carton. 2. Open the large box. Remove all packing materi- als and protective coverings from the unit and parts. NOTE: If any parts are missing or damaged, contact Antunes Technical Service IMMEDIATELY at 1-877- 392-7854 or 630-784-1000. - Page 8 A.J. Antunes & Co. HOT DOG CORRAL Food Shield (Optional) Item Part Description Qty. NOTE: Early style corrals do not have weldnuts on 2120121 Spacer inside of side covers. When installing the food shield, 3080158 Screw, Pan Hd., #8-32 x 5/8" jamnuts (5, figure 2) must be used.
-
Page 9: Operation
A.J. Antunes & Co. HOT DOG CORRAL OPERATION General Rocker Switch Volume, preference and experience will determine what (Power On/Off) temperature setting is best for your operation. When holding hot dogs for long periods of time, it is recom- mended to keep the setting under 160°F (71°C). This may vary depending on the type of hot dog used and the production rate required. -
Page 10: Cleaning
A.J. Antunes & Co. HOT DOG CORRAL Cleaning Left Side Cover The unit requires a minimum amount of maintenance. Driver Roller To ensure proper operation, clean the unit after every Driver Frame use. 1. Remove driver frame and wash in hot detergent Right Side Cover water using a soft brush. -
Page 11: Troubleshooting
A.J. Antunes & Co. HOT DOG CORRAL TROUBLESHOOTING WARNING To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equip- ment should be performed by qualified service personnel. The unit should be unplugged when servicing. Problem Possible Cause Corrective Action... -
Page 12: Wiring Diagrams
A.J. Antunes & Co. HOT DOG CORRAL WIRING DIAGRAMS HDC-20/20RC HDC-21A/30A/35A/50A P/N 1010609 Rev. E... -
Page 13: Replacement Parts
A.J. Antunes & Co. HOT DOG CORRAL REPLACEMENT PARTS (continued) HDC-20 INSET A 13 38 See Inset A DRIVE PARTS P/N 1010609 Rev. E... - Page 14 A.J. Antunes & Co. HOT DOG CORRAL HDC-20/20RC Item Part Description Qty. Item Part Description Qty. 0010434 Driver Assy. 0021214 Cover, Panel, LH 0501633 Panel, Rear 0501631 Panel, Bottom 0500551 Slide Bracket 4060304 Terminal Block 0020625 Slide Channel 2100130 Knob, Thermostat, F° 0700463 Power Cord, NEMA 5-15P, 120V 2100225...
-
Page 15: Replacement Parts
A.J. Antunes & Co. HOT DOG CORRAL REPLACEMENT PARTS (continued) HDC-20RC INSET A See Inset A DRIVE PARTS P/N 1010609 Rev. E... - Page 16 A.J. Antunes & Co. HOT DOG CORRAL HDC-20/20RC Item Part Description Qty. Item Part Description Qty. 0010434 Driver Assy. 0021214 Cover, Panel, LH 0501633 Panel, Rear 0501631 Panel, Bottom 0500551 Slide Bracket 4060304 Terminal Block 0020625 Slide Channel 2100130 Knob, Thermostat, F° 0700463 Power Cord, NEMA 5-15P, 120V 2100225...
- Page 17 A.J. Antunes & Co. HOT DOG CORRAL REPLACEMENT PARTS (continued) HDC-21A/31A/35A/50A INSET A See Inset A DRIVE PARTS 27 41 P/N 1010609 Rev. E...
- Page 18 A.J. Antunes & Co. HOT DOG CORRAL HDC-21A/31A/35A/50A Item Part No./Qty. Description HDC-21A HDC-30A HDC-35A HDC-50A 0010366 / 1 0020595 / 1 0010368 / 1 0020598 / 1 Driver Assy., 11 Rods, Standard – 0020989 / 1 – – Driver Assy., 10 rods, Special Order –...
- Page 19 A.J. Antunes & Co. HOT DOG CORRAL REPLACEMENT PARTS (continued) HDC-21A / 31A / 35A / 50A INSET A See Inset A DRIVE PARTS 27 41 P/N 1010609 Rev. E...
- Page 20 A.J. Antunes & Co. HOT DOG CORRAL Item Part No./Qty. Description HDC-21A HDC-30A HDC-35A HDC-50A – 218P113* / 1 – 218P113* / 2 Ratchet Fasteners Glide 215P151* / 1 215P151* / 1 215P151* / 1 215P151* / 1 Bearing, Crossover Shaft/Arm 310P146* / 1 310P146* / 1 310P146* / 1...
- Page 21 A.J. Antunes & Co. HOT DOG CORRAL NOTES P/N 1010609 Rev. E...
-
Page 22: Warranty
LIMITED WARRANTY Equipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been constructed of the finest materials available and manufactured to high quality standards. These units are warranted to be free from mechanical and electrical defects for a period of one year from date of purchase or 18 months from shipment from factory, whichever occurs first, under normal use and service, and when installed in accordance with manufacturer’s recommendations.
Need help?
Do you have a question about the HOT DOG CORRAL HDC and is the answer not in the manual?
Questions and answers