Advertisement
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
12. Do not use outdoors.
should always be followed to reduce the risk of fire,
13. To disconnect, grip plug and pull from wall outlet.
electric shock, and injury to persons, including the
Never yank on cord.
following:
14. Always use on a dry, level surface.
15. Do not operate fan until fully assembled with all
1. Read all instructions before using this appliance.
parts properly in place.
2. Use fan only for purposes described in the instruction
16. This product is intended for household use ONLY and
manual.
not for commercial or industrial applications.
3. To protect against electrical shock do not immerse
17. WARNING: To reduce the risk of electrical shock
unit, plug or cord in water or spray with liquids and
and injury to persons, do not use in window.
plug the appliance directly into a 120V AC electrical
18. WARNING: This fan is provided with an internal
outlet.
electronic fan speed control. To reduce the risk of fire
4. Close supervision is necessary when any appliance is
or electric shock, do not use this fan with any other
used by or near children.
solid-state speed control device.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
PLEASE READ AND SAVE
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
THESE IMPORTANT
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
SAFETY INSTRUCTIONS
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner.
10. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
11. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
BORGD1200-U_09EM1.indd 2
BORGD1200-U_09EM1.indd 2
F E AT U R E S - O P E R AT I O N S
ASSEMBLY INSTRUCTIONS
5. Secure the Fan Blade onto the Motor Shaft by turning
the Blade Cap counter clockwise and tighten firmly.
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS FROM
6. Center the Front Grill by aligning the BORG
THE PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
plate parallel to the floor, and then snap the Front
PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.
Grill into the clips located around the inner perimeter
1. Remove the Rear Grill Nut from the Motor Housing.
of the Rear Grill.
2. Line up the posts located on the front of the Motor
NOTE: you may need to loosen the Grill Screw
Housing with the holes located around the center of
located on the bottom of the Rear Grill prior to
the Rear Grill.
securing the Front Grill to the Rear Grill.
3. Secure the Rear Grill to the Motor Housing Assembly
7. Tighten the Grill Screw at the bottom of the Rear Grill.
by tightening the Rear Grill Nut over the threaded
8. Run the power cord through the opening located on the
post of the Motor Housing Assembly.
top of the base and pull the cord all the way through.
4. Slide the Fan Blade over the Motor Shaft making sure
Line the tabs located on the bottom of the stem with
the pins located on the Motor Shaft line up with
the holes located around the pocket of the base and
hollowed interior of the Fan Blade.
push the stem down until it is secured to the base.
Figure 1
D
F
H
I
J
E
OPERATING INSTRUCTIONS
1. Set fan on a dry, level surface.
2. Make sure that the Power/Speed Knob is in the off
position ( ). The Power/Speed Knob is located on
the front stem of the fan housing.
3. Plug cord into any standard 120 volt AC outlet.
L
4. Adjust the speed of your fan by turning the Power/
Speed Knob to the desired setting: 3-High, 2-Medium,
M
G
K
A
B
C
1-Low.
5. To turn the fan off turn the Power/Speed Knob to the
off position ( ).
6. The Oscillation Control Knob (
A. Logo Plate
the top of the Fan Motor Housing. To start Oscillation,
B. Front Grill
H. Motor Shaft
push Oscillation Knob all the way down. To stop
C. Blade Cap
I. Motor Housing Assembly
Oscillation, pull Oscillation Knob all the way up.
D. Fan Blade
J. Oscillation Knob
E. Rear Grill Nut
K. Power/Speed Knob
ADJUSTMENT INSTRUCTIONS
F. Rear Grill
L. Fan Stem
G. Rear Grill Screw
M. Base
Fan Head Tilt Adjustment
To adjust the angle of the fan head simply grab the stem
with one hand. With your other hand, adjust the angle of
the fan head.
C L E A N I N G / M A I N T E N A N C E
CLEANING/MAINTENANCE
Follow these instructions to correctly and safely care for
™
logo
your table fan. Please remember:
• Always unplug the fan before cleaning or
disassembling.
• Do not allow water to drip on or into the Fan Motor
Housing.
• Do not use any of the following as a cleaner:
gasoline, thinner, benzene.
NOTE: This fan can also be used during the cold winter
season to circulate warm air throughout your home.
Fan Blade Cleaning
1. To access the Fan Blade, loosen the Rear Grill Screw,
remove the Front Grill and the Blade Cap.
2. Clean the Fan Blade, Front Grill and Rear Grill with a
soft cloth moistened with a mild soap solution.
3. Replace blade, tighten the Blade Cap, and securely
fasten the Front Grill.
Fan Head and Base Cleaning
Using a soft, moist cloth, with or without a mild soap
solution, carefully clean the Fan Base and Head. Please
use caution around the Motor Housing area. Do not allow
the motor or other electrical components to be exposed to
water.
) is located on
FAN STORAGE
When storing your fan in the off season, it is important to
keep it in a safe dry location. It is important to protect
the fan head from dust.
If you have any questions regarding your product
please contact our Consumer Service Department at
1-800-397-5964 or visit our website at www.jardencs.com.
12/23/08 10:42:39 AM
12/23/08 10:42:39 AM
Advertisement
