RACKTUNER BTR2000 User Manual Table of Contents Important Safety Instructions ......3 Legal Disclaimer .............3 Limited Warranty ...........3 1. Introduction ............4 1.1 Before you get started ..........4 2. Control Elements and Connections ....4 2.1 Front ................5 2.2 Rear ................6 3. Input Channel Selection ........6 4.
RACKTUNER BTR2000 User Manual 4. Follow all instructions. 16. Where the MAINS Important Safety plug or an appliance 5. Do not use this apparatus near water. Instructions coupler is used as the 6. Clean only with dry cloth. disconnect device, 7. Do not block any ventilation the disconnect device shall...
1.1.3 Online registration recognize any pitch when tuning your instrument. It also offers 3 individually configurable functions in tuner mode: Please register your new BEHRINGER equipment right after your • With 11 different modes, the tuner lets you respond fully to the purchase by visiting http://behringer.com and read the terms and...
RACKTUNER BTR2000 User Manual 2.1 Front (3) (4) (8) (9) (1 Fig. 2.1: Operating elements on the left side of the BTR2000 The built-in microphone MIC can be used to tune the instrument TRANSPOSE/REF [TAP] button. Tuner mode: A short tap on this button lets you use the wheel (chapter 4.4.2) and calibrate the standard “A”...
(13) connector can either output the sounds generated by the unit and You can connect a single footswitch (such as the BEHRINGER the instrument signal or the instrument signal alone (chapter 3). DUAL A/B SWITCH AB200) to the 1/4" TS MUTE connector...
RACKTUNER BTR2000 User Manual ◊ ◊ To enable reference tones and the metronome, click to The LED bar on the BTR2000 can indicate deviations up be output from the MAIN connector, INPUT 2 must be to 50 cents (a quarter tone) sharp or flat. If the incoming...
RACKTUNER BTR2000 User Manual ◊ When you press the MUTE button, the MAIN output When it is switched off, the BTR2000 stores the selected (instrument sound and possibly the reference tone as well) is muted; tuner mode. the SOUND output is not affected.
RACKTUNER BTR2000 User Manual ◊ Turn the wheel to transpose up to 7 half-tones higher or lower. Any note can be played for the automatic calibration. The display indicates the number of half-tones by which a non- Connect your instrument to an input of the BTR2000. You can transposed instrument is too high ( 1 , 2, ..., 7) or too low...
RACKTUNER BTR2000 User Manual Custom tempering 5.3 Acoustic and visual BPM indicator Visual display The BTR2000 tuner makes it possible to tune using different temperings, whether existing or customized. This means that some The BTR2000 has two ways of indicating the selected tempo on the...
INPUT2/MIC inputs metronome Table 6.1: Options overview If you have a double footswitch such as the BEHRINGER FS112, it must be connected to the SELECT connector! Both functions (MUTE and SELECT) are then transmitted over a stereo connection and can be controlled using the two buttons.
Ensure a sufficient air supply and to not place your BTR2000 on an end, for example, to prevent the unit from overheating. 8.2 Audio inputs and outputs sleeve (ground/shield) All audio inputs and outputs on the BEHRINGER BTR2000 are laid out as mono TS connectors. (signal) Fig. 8.1: 1/4" TS connector...
9. Specifications Weight approx. 1.24 kg (2.73 lbs) BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these Audio Connectors efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or shown.