MT2205 SERVICE MANUAL COLOR TELEVISION RECEIVER ORIGINAL MFR’S VERSION A Design and specifications are subject to change without notice.
Page 2
MT2205 SERVICE MANUAL COLOR TELEVISION RECEIVER REVISION 1 MFR’S VERSION C The ORIGINAL SERVICE MANUAL of MFR’S VERSION A is mistaken for MFR’S VERSION B. MFR’S VERSION IC101 OEC3041A OEC3041B Please file this revision with the original version.
Page 3
Change of IC101 DIFFERENCES MFR'S VERSION B MFR'S VERSION C REF.NO PART NO. DESCRIPTION PART NO. DESCRIPTION IC101 I53F53041A IC OEC3041A I53F53041B IC OEC3041B PCB010 A3G813C01A MAIN PCB ASS'Y TM9436A A3G813C01B MAIN PCB ASS'Y TM9436A SPEC.NO. M3G8-13C O/R NO. W043007...
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
CONTENTS SERVICING NOTICES ON CHECKING ....................A1-1 HOW TO ORDER PARTS ........................A1-1 IMPORTANT ............................A1-1 CONTENTS .............................. A2-1 GENERAL SPECIFICATIONS ........................A3-1~A3-4 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ....................... SERVICE MODE LIST ..........................CONFIRMATION OF USING HOURS ...................... NOTE FOR THE REPLACING OF MEMORY IC ..................
G E N E R A L S P E C I F I C A T I O N S G-1.Outline of the Product inch(544.5mmV):Measured diagonally Color CRT 90 degree deflection G-2.Broadcasting System System G-3.Color System NTSC SECAM or Monochrome signal G-4.NTSC Playback(PAL 60Hz) G-5.NTSC 3.58+4.43/PAL60Hz G-6.Antenna Input Impedance...
Page 7
G E N E R A L S P E C I F I C A T I O N S G-17. P rotector: Power Fuse G-18.Regulation Safety NEMKO FEMKO DEMKO IEC65 SEMKO HOMOLO SABS SISIR AS3159 DENTORI GOST NONE Radiation SABA HOMOLO...
Page 8
G E N E R A L S P E C I F I C A T I O N S G-26.OSD Language OSD Language Setting Not Applicable G-27.Speaker 6 1/3 x 2 1/4 inches Imp. ohm x Max 2.5 + 2.5 W (Typical) 10% 2.0 + 2.0 W (Typical) G-28.EXT Speaker G-29.Carton...
Page 9
G E N E R A L S P E C I F I C A T I O N S G-32.Switch Front Power(Tact) Channel Up Volume Up System Select Channel Down Volume Down Main Power SW Sub Power Rear AC/DC TV/CATV Selector Degauss...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 2 seconds. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD.
ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL 1. RF AGC DELAY ADJUSTMENTS 2. VIDEO LEVEL Read and perform these adjustments when repairing the 3. FM LEVEL circuits or replacing electrical parts or PCB assemblies. 4. OSD H 5. CUT OFF CAUTION 6.
Page 13
ELECTRICAL ADJUSTMENTS 2-5: SUB TINT/SUB COLOR 2-8: VERTICAL SIZE Receive the color bar pattern. Receive the crosshatch pattern. Connect the synchro scope to pin 1 of CP101 and the Using the remote control, set the brightness and pin 6 (GND) of CP101. contrast to normal position.
Page 14
ELECTRICAL ADJUSTMENTS [ TV ] OSD H Fig. 2-8 2-12: SEPARATION 1, 2 Receive the stereo signal. Connect the AC voltmeter to CP351 through stereo filter (400Hz, 2KHz). Activate the adjustment mode display of Fig. 2-1 and press the channel button (7) on the remote control. The Fig.
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
Page 23
POWER SCHEMATIC DIAGRAM CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501) FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES 4A 125V D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 4A 125V (F501). DEGAUSE COIL L502 CP502...
Page 24
STEREO/SOUND AMP SCHEMATIC DIAGRAM FROM/TO MICON/TUNER I2C_SDA I2C_SCL AUDIO_MUTE L704 FROM IF/CHROMA 22uH P.CON+9V TU_AUDIO_OUT R752 C775 FROM/TO POWER 1.8K 0.033 M C770 C777 0.022 0.47 1.8K TONE 136K AMP1 I2C BUS INTERFACE SIMAMP1 VOLAMP1 6.5K 6.5K 6.5K VOLAMP2 R729 C748 CONTROL SIMAMP2...
WAVEFORMS MICON/TUNER 200mV. 5ms/div 0.5V. 20µs/div 1V. 0.5ms/div 20V. 20µs/div 0.5V. 20µs/div 0.5V. 20µs/div 200mV. 20µs/div 0.5V. 20µs/div 200mV. 20µs/div 200mV. 5ms/div 200mV. 20µs/div 14 0.5V. 5ms/div IF/CHROMA 1V. 20µs/div 0.5V. 20µs/div 0.5V. 2ms/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS 50V. 20µs/div 16 1V. 20µs/div 200V. 20µs/div STEREO/SOUND AMP 27 200mV 1ms/div 1V. 20µs/div 10V. 5ms/div DEFLECTION/CRT 18 0.5V. 5ms/div 5V. 5ms/div 28 200mV 1ms/div 20V. 20µs/div 50V. 20µs/div 2V. 20µs/div 50V. 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.