Sony CDX-GT420IP Operating Instructions Manual page 19

FM/AM
Compact Disc Player
---
~
m
A
*
AUDIO OUT SUB/REAR
3-217-562-11 (1)
Installation/Connexions
Installation/Connections
SONY
B
CDX-GT420IP
---
~
*
AUDIO OUT SUB/REAR
© 2007 Sony Corporation
Printed in China
Canneulian example
[I]
Ca••eulio. diagram
I]]
Notes
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
o
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
e
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see "Notes on the control and power
supply leads."
e
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
o
To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If there is no accessory position, connect to the + 12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to
a
metal surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see "Notes on the control and power
supply leads."
o
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to
a
metal
surface of the car first.
Call1ioliB
.bll lill
rn .
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power supply leads only
after all other leads have been connected.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
• The numbers in the list are keyed to those in the
instructions.
• The bracket
CD
and the protection collar @ are
attached to the unit before shipping. Before mounting
the unit, use the release keys
®
to remove the bracket
CD
and the protection collar
@
from the unit. For
details, see "Removing the protection collar and the
bracket
(EI)"
on the reverse side of the sheet.
• Keep the release keys
®
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
CD
carefully to avoid injuring your
fingers.
x2
®
Power amplifier
Amplificateur de puissance
iPod
x4
®
®
Front speaker
Haut-parleur avant
Rear speaker
Haut-parleur arriere
Equipment used in illustrations (not supplied)
Appareils utilises dans les illustrations (non fournis)
o
Active subwoofer
Caisson de graves actif
Catch
Note
Before installing, make sure that the catches on both sides of
the bracket
CD
are bent inwards 2 mm (3/32 in).
If
the catches are
straight or bent outwards, the unit will not be installed securely
and may spring out.