1. Manuals
  2. Brands
  3. DynDNS Manuals
  4. IP Camera
  5. DDK-1500
  6. Installation & operation manual

DynDNS DDK-1500 Installation & Operation Manual

Mpeg-4 ip camera high resolution day & night (poe)
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION &
OPERATION MANUAL
MPEG-4
IP CAMERA
High Resolution Day & Night (PoE)
DDK-1500
(NTSC)
Before trying to connect or operate this product, please read this manual completely

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DDK-1500 and is the answer not in the manual?

Questions and answers

Related Manuals for DynDNS DDK-1500

Summary of Contents for DynDNS DDK-1500

  • Page 1 INSTALLATION & OPERATION MANUAL MPEG-4 IP CAMERA High Resolution Day & Night (PoE) DDK-1500 (NTSC) Before trying to connect or operate this product, please read this manual completely...

  • Page 3: Table Of Contents

    Table Of Contents SAFETY PRECAUTIONS ................3 1. PRODUCT FEATURES................4 1.1 P ..............4 RODUCT NSTRUCTIONS 1.2 P ................5 RODUCT EATURES 1.3 T ..............5 ECHNICAL PECIFICATIONS 2. DESCRIPTION OF THE FRONT/REAR VIEW .........7 2.1 F ............7 RONT ANEL AND ANEL 2.2 F ..................8 LANK ANEL...
  • Page 4 5. Operating Instructions for Image Software and Network....24 5.1 M ............25 ICROSOFT NTERNET XPLORER 5.1.1 Connecting the IP camera ........................25 5.1.2 Change Image Setting ........................27 5.1.3 Change the Network Setting ......................30 5.1.4 Change the System Setting ......................39 5.1.5 Change the Application Setting .......................47 5.1.6 Change the SD card Setting ......................53 5.1.7 Change the Pan/Tilt setting ......................54 5.1.8 PPPoE &...

  • Page 5: Safety Precautions

    SAFETY PRECAUTIONS All the following safety and operational instructions to prevent harm or injury to the operator(s) or other persons should be read carefully before the unit is activated. WARNING To prevent fire or shock hazard, avoid exposing this unit to rain or moisture. Do not block ventilation openings.

  • Page 6: Product Features

    1. PRODUCT FEATURES 1.1 Product Instructions This user-friendly device combines cutting-edge sophistication with practical reliability and convenience, high performance with smooth remote communication. Just plug in the network cable!! You’ll get live streaming Video & Audio anytime any place! You’ll have security you can rely on! The especially high resolution has 520 TV lines, a built-in web server and a Network interface to connect you with the Internet securely and fast.

  • Page 7: Product Features

    1.2 Product Features • 1/3" SONY Super HAD CCD. • Mechanical IR Cut Filter. • MPEG4 / MJPEG video compression. • High resolution: 520 TV • Supports POE. • Embedded web server. • Supports a built-in microphone. • Supports motion detection. •...
  • Page 8 ‧5 levels of compression provided. The file size of an M-JPEG compressed image depends on the image’s actual content. Images with a lot of detail will generate bigger files. The level of compression determines the image quality. High compression requires smaller files while low compression gives you finer image quality along with bigger files.

  • Page 9: Description Of The Front/Rear View

    2. DESCRIPTION OF THE FRONT/REAR VIEW 2.1 Front Panel and Rear Panel -- Front Panel -- -- Rear Panel -- MICROPHONE: The IP camera has an additional audio function. The device has a microphone built into its front panel which records sound. Plug Inlet: A DC 12V inlet that connects to an external power supply.

  • Page 10: Flank Panel

    2.2 Flank Panel -- Left Flank Panel -- -- Right Flank Panel -- Lens Mount: This IP camera is used with either a C or a CS mount lens. DIP Switch: 1. AES: Auto electric shutter. 2. DC IRIS: Use an auto iris (DC drive) 3.

  • Page 11: The Usb Function

    2.3 The USB function By connecting the IP camera with a PC via the USB connector, the IP camera can provide two different functions. 1. Insert an SD card: As a card reader. Insert an SD card into the IP camera, then connect to the PC. You might transfer files between the SD card and the PC.

  • Page 12: Poe (Power Over Ethernet)

    2.4 PoE (Power over Ethernet) These technologies will enable the development of new networked appliances, by providing power as well as data over existing Ethernet cables. The Summary Comparison of PoE Standards (Table 1) is listed as follows. Table 1. Summary Comparison of PoE Standards SOURCE LOAD Ethernet RJ-45 connector pin number *...

  • Page 13: Installation

    3. INSTALLATION Please follow the instructions and the diagram below to set up the system. NOTE: The ipxcam is linked by its Video Out connection via a BNC connector to a monitor's Video In connection. If this connection is there, you can see some information on the monitor screen, such as the IP camera factory default Static IP address(192.168.1.168).

  • Page 14: Connecting With A Multiplexer

    3.3 CONNECTING WITH A MULTIPLEXER LAN CAMERA 1 LAN CAMERA 2 TO LAN CAMERA VIDEO OUT BNC CONNECTOR LAN CAMERA 16 3.4 UPDATING SYSTEM SOFTWARE If the system software of the IP camera needs to be upgraded, please take the following steps to safely process it.
  • Page 15 9. If the message "UPDATE NG RESET PLEASE" appears rather than "UPDATE OK RESET PLEASE", please write down the error messages shown on the screen and inform your technical support, while ignoring the following steps. 10. Power off the IP camera when this update process is finished, then remove the SD card from the IP camera.

  • Page 16: Ip Camera Sd Card Troubleshooting

    3.5 IP camera SD card Troubleshooting 1. Check if the SD card position is correct or not. Please refer to the manual for the related information. 2. After powering the IP camera on, correctly insert the SD card, and a little icon of "SD" will show up in the upper-right corner of the monitor screen.

  • Page 17: Network Configuration

    4. Network Configuration 4.1 Cable Connections Please follow the instructions below to connect your IP camera to a computer or a network and to choose a proper RJ-45 cable configuration for connections. Physical specifications of the RJ-45 cable for Ethernet Cat.

  • Page 18: Connect To A Lan Hub (Intranet)

    4.1.2 Connect to a LAN Hub (INTRANET) The RJ-45 PIN configuration for connecting with a LAN Hub is shown below. TO PC NETWORK CARD LAN CAMERA RJ-45 uplink...

  • Page 19: Configure Your Ip Camera Network Settings

    4.2 Configure Your IP camera Network Settings Upon connecting with the network hardware, you need to activate the network function and configure the proper network settings of the IP camera. 4.2.1 Enable DHCP Function This function can only work if the LAN, which the unit is connected to, has a DHCP server. If the DHCP server is working, please move the dip switch points up to 3 on the flank panel;...
  • Page 20 NOTE: When connecting to a network, each connected IP camera must be assigned a unique IP, which must be in the same class type as your network address. IP addresses are written as four sets of numbers separated by periods; for example, 192.168.1.1 Therefore, if the connected network is identified as Class C, for example, the first three sets of numbers of the IP camera IP address must be the same as the network address.

  • Page 21: Tcp/Ip Communication Software

    4.3 TCP/IP Communication Software Follow the procedure below to install the TCP/IP communication program in your computer. Click the Start menu from your computer, and point to the Settings/Control Panel. Double click the Network icon to enter the windows.

  • Page 22: Tcp/Ip Installation

    Click the Configuration tag, and check if the TCP/IP is included among the network components list. If the TCP/IP is included, please process section 4.5. If it is not included, please follow section 4.4 to install the TCP/IP. 4.4 TCP/IP Installation During the installation, you will be requested to insert the Windows CD-ROM.

  • Page 23: Tcp/Ip Configuration Setting

    4.5 TCP/IP configuration setting Click Start → Settings → Control Panel → Network. Select TCP/IP, and then click Properties. Before processing the IP camera installation in a WAN, please make sure the Internet connection works properly. If not, please contact your ISP provider. 　...

  • Page 24: Connection Testing

    4.6 Connection Testing With the previous settings, follow the instructions below to ensure whether you have established the connection successfully. Click Start → Programs → MS-DOS Prompt Type in ping 192.168.1.168, then enter. (See the sample screen below). ** This IP is the IP camera IP address that is assigned for the connected IP camera in step2.
  • Page 25 If you receive a response as in the sample screen below, the connection hasn’t been successfully established. Please re-check all the hardware and software installations by repeating steps 1 to 5. If you still can’t establish the connection after rechecking, please contact your dealer.

  • Page 26: Operating Instructions For Image Software And Network

    5. Operating Instructions for Image Software and Network Two choices of software are available for linking with the IP camera: (1) the Microsoft Internet Explorer; and (2) the IP camera VIEWER, a network browser in a PC which provides the functions of monitoring remote zones or watching recorded data through the TCP/IP protocol.

  • Page 27: Microsoft Internet Explorer

    5.1 Microsoft Internet Explorer 5.1.1 Connecting the IP camera Start up the Microsoft Internet Explorer, and then follow the steps below to connect the IP camera. Click the URL block at the top of the window. Enter the URL address of the IP camera into the URL block and press the “Enter” button to enter the home page.
  • Page 28 Browsing images from the IP camera The images from the IP camera will be displayed on the home page while going online with the IP camera. Some buttons of the home page are provided for further setting. In MJPEG mode or in MPEG4 mode, there are different display formats of its home page.

  • Page 29: Change Image Setting

    5.1.2 Change Image Setting Please follow the steps below to change the image setting through the network if necessary. 1. Click the Image button on the home page to enter the image-setting page. Image setting page of MJPEG mode Image setting page of MPEG4 mode 2.
  • Page 30 6. Click the Day & Night button to enter the Privacy Mask page. Click the drop-down list to choose the Day & Night mode of “Auto”, “Day mode”, “Night mode” and “Schedule”. Note: In the “Schedule” mode, you can click the icon to set the Day or Night mode of each hour.
  • Page 31 7. Click the Home button to return to the home page while the new image setting acts on the images to effect the desired changes instantly. (If the setting has not been changed by the above steps, any (re)entry onto the home page will find images in their earlier or original setting.) Exchange the image format Tick on one of the formats then press the Submit button.

  • Page 32: Change The Network Setting

    5.1.3 Change the Network Setting Please follow the steps below to change the network setting through the network if necessary. Set the network options and IP address. Click the Network button in the home page to enter the Network page. The accessible networks here are the “SNTP”, “DDNS”, “PPPoE”, ”UPnP”...
  • Page 33 Description of function keys: IP Address: Enter the 4-byte IP Address in the appropriate blank space (the value in each box may be anywhere between 0 and 255). Every IP camera has to own an IP address to be identified on the network. Netmask: Fill in the 4-byte Subnet Mask in the required blank spaces (usually any numbers between 0 and 255).
  • Page 34 Change the Network Setting — SNTP. Please follow the steps below to change the SNTP setting through the network if necessary. Click the SNTP button at upper left above to enter the “SNTP Server Setting” page. Enter the IP Address of the SNTP server, and choose one of the time zones as and when necessary.
  • Page 35 Click “Enable DDNS Function” to checkmark the attached box and activate the function. Click ”DDNS Type” to open the list of two DDNS modes to choose from: “DynDNS” and “hn”. Click the “Apply” button and connect their website automatically and visit it. Type in your dynamic IP Address and Email Address.
  • Page 36 Enable DDNS Function: Checkmark to activate the function. DDNS Type: Click to open the list of two DDNS modes to choose from: “DynDNS” and “hn”. Click the “Apply” button and connect this website automatically and enter it. Type in your dynamic IP Address and Email Address.
  • Page 37 Change the Network Setting — PPPoE. The “Network” page has, on its upper left, the “PPPoE” icon. Please follow the steps below to change the PPPoE setting through the network if necessary. Click the PPPoE button at upper left above to enter the “PPPoE Setting” page. Please read the “PPPoE Troubleshooting”...
  • Page 38 Change the Network Setting —UPnP. The “Network” page has, on its upper left, the “UPnP” icon. Please follow the steps below to change the UPnP setting through the network if necessary. Click the UPnP button at upper left above to enter the “Universal Plug and Play” page. Click “Enable UPnP”...
  • Page 39 Change the Network Setting — IP Filter The “Network” page has, on its upper left, the “IP Filter” icon. Please follow the steps below to change the IP Filter setting through the network if necessary. Click the IP Filter button at upper left above to enter the “Network Setting” page. Click “Enable IP Filter”...
  • Page 40 Change the Network Setting —Network Traffic. The “Network” page has, on its upper left, the “Traffic” icon. Please follow the steps below to change the UPnP setting through the network if necessary. Click the Traffic button at upper left above to enter the “Network Traffic” page. Type in the “Maximum Upload Bandwidth”...

  • Page 41: Change The System Setting

    5.1.4 Change the System Setting Please follow the steps below to change the date and time of the system setting through the network if necessary. Set the Date and Time of the system 1. Click the System button in the home page to enter the “Date And Time” page (default). 2.
  • Page 42 Change the System Setting — Timestamp. Please follow the steps below to change/add the timestamp through the network if necessary. 1. Click the Timestamp button on the left side of the “System - Date and Time” page to enter the “System - Timestamp”...
  • Page 43 Change the System Setting — Users. Please follow the steps below to change/add the users’ authority through the network if necessary. Click the Users button on the left side of the “Date and Time” page to enter the “Users” page. Add, modify or delete any user’s data if necessary.
  • Page 44 Change the System Setting — Digital I/O. Please follow the steps below to change the Digital I/O through the network if necessary. Click the Digital I/O button on the left side of the “Date and Time” page to enter the “Digital I/O Setting”...
  • Page 45 Change the System Setting — Audio Mechanism. Please follow the steps below to change the Audio Mechanism through the network if necessary. Click the Audio Mechanism button on the left side of the “Date and Time” page to enter the “Audio Mechanism Setting”...
  • Page 46 Change the System Setting — RS485 Setting. Click the RS485 Setting button on the left side of the “Date and Time” page to enter the “RS485 Setting” page. Description of function keys: Baud rate: Eight different speeds can be used: 2400 baud per second, 4800 baud, 9600 baud, 19200 baud, 28800 baud, 38400 baud, 57600 baud and 115200 baud.
  • Page 47 Change the System Setting — Update Firmware. Please follow the steps below to update the firmware through the network if necessary. Click the Update Firmware button on the left side of the “Date and Time” page to enter the “Update Firmware”...
  • Page 48 View the Event Logs. Please follow the steps below to view events through the network if necessary. Click the Events button on the upper left above to enter the “Event Log” page. Choose one of the three buttons shown on the page to view an event when necessary. The three buttons are titled “First Page”, “Previous 20”, and “Next 20”.

  • Page 49: Change The Application Setting

    5.1.5 Change the Application Setting Please follow the steps below to change the application setting through the network if necessary. Change the Application Setting — SD Card Application Setting. Please follow the steps below to change the SD CARD setting via the network if necessary to upload recording data live.
  • Page 50 Change the Application Setting —Language Setting. Please follow the steps below to change the Language setting via the network if necessary. Click the Language button on the left side to enter the “Language Setting” page. You have an option as to which language to use. The default is “English” Click your selected language and click "Submit"...
  • Page 51 Change the Application Setting —Record Application Enable Setting. Please follow the steps below to change the setting via the network if necessary. Click the Enable Record button on the left side of the record to enter the “Record Application Enable Setting” page. Click “Enable Record –...
  • Page 52 Change the Application Setting —Record - Schedule. Click the Application button on the home page to enter the “Record - Schedule” page. Check/uncheck any/all of the first seven boxes set vertically in the upper half of the “Schedule” page to enable/disable the programmed recording function, and vary the setting of the targeted item while it is enabled.
  • Page 53 Change the Application Setting — Alarm Application Enable Setting. Please follow the steps below to change the setting via the network if necessary. Click the Enable Alarm button on the left side of the record to enter the “Alarm Application Enable Setting”...
  • Page 54 Change the Application Setting — Alarm - Motion Detection. Please follow the steps below to enable changes in the motion detection function of the alarm through the network if necessary. Set the motion detection: Click the Motion Detection button on the left side of the Alarm to enter the “Alarm – Motion Detection”...

  • Page 55: Change The Sd Card Setting

    5.1.6 Change the SD card Setting Please follow the steps below to change the SD card setting through the network if necessary. Change the SD card Setting — FILELIST of MEMORY CARD. Please follow the steps below to change the setting via the network if necessary. Click the “SD card”...

  • Page 56: Change The Pan/Tilt Setting

    5.1.7 Change the Pan/Tilt setting Click the Pan/Tilt button on the home page to open the Speed Dome Controller. Click “Configure” to enter to the RS485 setting page (please refer to Change the System Setting — RS485 Setting). Select a Speed Dome device ID from the drop-down list on the Speed Dome Controller. The Controller will display the corresponding ID.

  • Page 57: Pppoe & Ddns

    5.1.8 PPPoE & DDNS Using the PPPoE Install the XDSL software (obtained from your ISP dealer) in your PC. Search your IP camera's IP address: you can use your Network Viewer's Scan IP program, or just connect the ipxcam and the Video monitor. The monitor screen will show the IP address on its right side.
  • Page 58 Test: Go to the Internet. Set your PC to enter the Internet. Desktop → IE browser → Type in the IP camera IP address (the same address as in the PPPoE settings and step 3 above) → You can see the ipxcam’s images. DDNS settings Check your IP camera’s IP address ( Scan IP software or monitor ) →...

  • Page 59: The Ip Camera Ip Surveillance

    5.2 The IP camera IP Surveillance This section provides instructions for installing and using the IP surveillance and Image Viewer, which are included with the IP camera. The programs can be operated by a selected PC equipped with the following requirements. System Requirements Intel Pentium 1.5 GHz processor or above (2.8 GHz or higher recommended).

  • Page 60: Install The Ip Surveillance In Your Pc

    5.2.2 Install the IP surveillance in your PC Install the IP surveillance from the supported CD-R. 1. Exit all applications currently running in the selected PC. 2. Insert the supported CD in the CD-ROM drive. The program will execute the installation automatically.

  • Page 61: Login The Network Camera Software

    5.2.3 Login the Network camera software Once the IP surveillance is executed, a Login prompter will appear. You must enter the default User Name: root, and the password: Admin in the respective spaces. Click the “OK” button and enter the console page of the IP surveillance: both the user name and password must be entered correctly.
  • Page 62 Press the button to enter the Settings page. Press the button to add a new device group. After typing in the Group Name, please press the OK button. Add a channel from the button. (1) Click the Auto-Search button at the bottom of the "Connect Network camera Wizard"...
  • Page 63 This page provides the IP Address, the device type, and the MAC Address. After typing the Site name and selecting the Connect Mode, please click the "Next" button to access the next "Connect Network camera Wizard" page. NOTE: Please click the icon to see the details of the Connect Mode.

  • Page 64: Operation

    5.2.4 Operation 5.2.4.1 Live Monitor Once the connection has been established, click the button to enter the Live Monitor window. (See the sample screen below.) On the left side of the window is the connected device that has been arranged when you established the connection. The Live Monitor icon.
  • Page 65 multi-screen, and one sequence; the picture will sequentially switch to different channels according to the Sequence Views setting (refer to 5.2.4.3). Note: One can’t use the common icon (#11) in the Sequence displaying mode or drag the video and drop it as s/he likes. For the further settings of each channel, please select the device title on the left side and click the right mouse key to operate.
  • Page 66 ◇Delete a camera video from the Live Monitor area: (1) Select the video of the camera which you want to delete. (2) Press and hold the left mouse button. Then drag it to the trashcan release the mouse button. 12. Alarm list / PTZ Control: Shows the alarm types, the device names and the occurrence time.
  • Page 67 5.2.4.2 Playback Viewer Press the button to enter the Playback Viewer setting page. The Playback Viewer icon. The display area. Click to choose the Recording List Live Event Message The alarm events which were recorded will be marked in pink color. Click to refresh the recording list.
  • Page 68 NOTE: To view the alarm lists of a camera which were recorded, please (1) click the icon (2) the Alarm List window will appear as shown below, (3) select a camera from the drop-down list, then (4) click the “Search” button. Move to the left/right area.
  • Page 69 Play Rate: During play mode, please use the scroll bar to control the show speed. Shows the device title. This allows you to search a recorded video kept in the HDD of the device. Enter the MONTH /DAY /YEAR /HOUR /MINUTE you wish to search and click to proceed.
  • Page 70 5.2.4.3 Setting Press the button to enter the Setting page. The Setting page. Function buttons: Add a new device group: Click this button and type in the new group, then press “OK” to save it. Remove a device group: Click this button and select the group name, then press “OK”...
  • Page 71 Device Setting: Provides four pages of settings. (1) Device Setting page (2) Image Setting page NOTE: The IP Surveillance software connects the Internet to a Network camera. There may be a problem if the bandwidth is not enough, in which case the speed rate of the image transmissions may become too low.
  • Page 72 (1) Global Settings Monitor setup: Sets the date/time mode and display mode, and controls the CPU use percentage on five levels. Default Directory: Sets the default files’ saving path. Click to select the directory. (2) Event Notification Channel Prompt: Sets each camera to activate or deactivate the three modes of "Motion Buzzer", "Sensor Buzzer", and "Alarm Focus".
  • Page 73 Popup Message: Sets the maximum number of the pop-up messages, the displaying time and the pop-up forms. Tick mark the blank space for each device to activate it. E-mail Notice: Sets each camera to activate the E-mail Notice function of the three situations: "Motion Alarm", "Sensor Alarm", and "DISK Full".
  • Page 74 (3) Recording Settings Recording Settings: You can control the HDD reserved space by using the scroll bar. Recording quota setting: Set the maximum recording quota of each channel. (4) Scheduler (1) Choose one of the devices to set its recording schedule. (2) Select the period: Click to set to record only once or record every day.
  • Page 75 (3) Select the recording time: Sets the periods of time in recording. Select the Begin time and the End time the time markers will display above. Please use the up (increase) and down (decrease) arrows to adjust the setting. Add the selected period schedule. You can also hold down the left mouse button to drag a period.
  • Page 76 The user has to modify the “Sequence Views Setting” to make it work. For example, if you want to see the 4-window sequence, please follow the steps given below: Step 1: Click the Sequence Views button to enter the Sequence Views setting page. Step 2: Select the “4 SEQ views”...
  • Page 77 (6) Speed Dome Tick mark to activate the Speed Dome Controller function of the selected channel. The user can set the model, ID and the protocol here. Click “Configure” to enter to the RS485 setting page. (7) Authority Setup Authority setup: Change or add the user’s authority. There are three different levels of authority , namely Admin, Operator and Viewer.
  • Page 78 List of cameras and its groups: The users can use the icons above the list to change the groups’ names, the devices’ titles and the channels’ display modes. Display area: Click the title of the camera, and you will see the live image in this area.
  • Page 79 5.2.4.4 Lock Press the button to lock the operation of this software, and the IP Surveillance monitor will be minimized into the systray*of the Windows taskbar. To unlock the command, please click the button once, then type in the correct password. The Microsoft Windows systray is a portion of the Windows 95, Windows 98, Windows ME, Windows NT, Windows 2000, and Windows XP Operating Systems that helps display running programs.
  • Page 80 5.2.4.7 Exit Setting Press the button to exit the IP surveillance monitor which is minimized into the systray of the Windows taskbar. Click the button to select the functions on the list. You can also change the password by clicking the “Tools” and “Change password” items on the list.

  • Page 81: The Image Viewer

    5.2.4 The Image Viewer The Network camera is equipped with a digital watermark. It's a checking software which protects archived images and informs you whether the images have been modified or not. Follow the instructions below to open an archived image from an SD card or an HDD.

  • Page 82: Advanced Operation

    6. ADVANCED OPERATION Question 1: How to view the live images of the IP camera via the Microsoft Internet Explorer on the Desktop PCs or the laptop computers in a situation where there are no monitors or television? ◇The way to get the IP address of the IP camera without a monitor: There are three way to get the IP address: Scan IP, UPnP and IP function.
  • Page 83 4. If you didn’t set the other player before, the AVI file will be played by the Windows Media Player. Question 3: How to use the DynDNS to connect the IP camera by using its Sub Hostname via the intranet? ◇Set the DDNS function...
  • Page 84 3. Choose “ON” from the “PPPoE mode” list to activate it. 4. Enter the Account and the Password which are provided from your ISP. 5. Click the Submit button to submit the setting. NOTE: Please refer to section 5.1.8 for more details. ◇Use the Sub Hostname to view the IP camera 1.

  • Page 85: Specifications

    7. SPECIFICATIONS Model Number DDK-1500 Video sensor 1/3" Sony Super HAD CCD (with HQ1 DSP) System NTSC Horizontal resolution 520 TV lines Lens C/CS mount Video Auto Iris type DC-iris Day and Night Mechanical IR Cut Filter: Auto; Color / Monochrome 2500°K ~ 9500°K...

  • Page 86: Functions Of Client Pc

    Video output 1.0 Vpp, 75 ohm, composite, negative, BNC x 1 Alarm I/O 1 input / 1 output Serial port RS-485 Connectors SD card Alarm and Schedule recording / update Configuration / Update Reset Factory Default LED indicator Power / Network indicator Power requirement DC12V / PoE Operating Temperature...

  • Page 87: Appendix 1. -Scanip

    APPENDIX 1. –SCANIP Follow the instructions below to use the SCANIP software to search the IP camera devices from a local location. Click the button to discover the connection of the all-type device in the LAN. The Device List will display the connection of the all-type device. Select the desired device from the Device List.
  • Page 88 If you have clicked “No”, please manually type in insertions as required in the “Free IP Address”, “Gateway Address”, and “NET Mask”. Follow each insertion you make by typing in the “Login Name” and “Password”, and click “UPDATE” to send your alterations to the IP camera.
  • Page 89 enter it into an IP Address on the left. To change any IP address, type in the new address in the “Free IP Address” box on the right as well as the device “Login Name” and “Password” in their respective blanks at bottom left, then click “UPDATE”, and the new address will automatically be sent to the device.

  • Page 90: Appendix 2. -Ip Camera Upnp How To

    APPENDIX 2. –IP camera UPnP How To ® The most troublesome issue when you setup an ipxcam is that you have no idea what the IP ® address of this device is. Now ipxcam supports the UPnP (Universal Plug and Play) protocol ®...
  • Page 91 Figure 2 Step 2: When Control Panel appears, double-click the Network Connections icon. The Network Connections dialog box appears. See Figure 3. Figure 3 Step 3: Click the Protocols tab in the Network Connections dialog box. See Figure 4. Figure 4 Step 4: When the Local Area Connection Properties dialog box shows up, choose Internet Protocol (TCP/IP) and click Properties.
  • Page 92 Figure 5 Step 5: In the Internet Protocol(TCP/IP) Properties dialog box, choose Use the following IP Address to indicate that you do not wish to use DHCP, and assign IP Address 192.168.1.200 with Subnet mask 255.255.255.0. Click OK when you finish it. See Figure 6. Figure 6 Step 6: Choose Close to finish the modification.
  • Page 93 2. Install UPnP Packets ® As described before, Microsoft Windows XP doesn’t start the UPnP service by default; however, we have to install some packets before we initialize it. The following steps will help you to install them. Step1: From the Start menu, point to Set Program Access and Default, and then click it. See Figure 8 Figure 8 Step 2: When the Add or Remove Programs dialog box appears, click the Add/Remove...
  • Page 94 Figure 10 Step 4: Check UPnP User Interface, and choose OK. See Figure 11. Figure 11 Step 5: When the original Network Component Wizard dialog box returns, click Next. See Figure12. Figure 12...
  • Page 95 Step 6: After about one minute the UPnP installation will be done, and choose Finish to close it. See Figure13. Figure 13 3. Turn on Services After installation, we should turn on the relative services to start the UPnP protocol. The following procedures will teach you how to do it.
  • Page 96 Figure15 Step 3: Click the Services icon in the Administrative Tools dialog box. See Figure16. Figure16 Step 4: When the Services dialog box shows up, double click the SSDP Discovery Service icon. See Figure17.
  • Page 97 Figure17 Step 5: Choose Automatic in the Startup type, and click OK to start it. See Figure18. Figure18 Step 6: When the Services dialog box appears again, double click the Universal Plug and Play Device Host icon. See Figure19.
  • Page 98 Figure19 Step 7: Choose Automatic in the Startup type, press the Start button, and click OK to start it. See Figure20. Figure20 Step 8: Restart your system.
  • Page 99 ® 4. Scan ipxcams through My Network Place After your installation and starting services, the UPnP protocol will take effect. You can scan all ® ipxcams in My Network Place like Figure21 and Figure22 below. Figure21 Figure22 Just double click the UPnP MPEG4 IP camera the video live stream will pop up automatically ®...

  • Page 100: Appendix 3. -The Arp Function

    APPENDIX 3. –The ARP function Setting the IP Address The Ethernet interface on the ipxcam has a default IP address (192.168.1.168) that most likely needs to be changed to make it work on your local network. You need to acquire a unique IP address (ask your network administrator).
  • Page 101 ARP and ping from UNIX or GNU/Linux: Start a shell Type the following as superuser (root): arp -s <IP address> <Ethernet address> [or arp -s <IP address> < MAC address>] ping <IP address> Example: arp -s 192.168.1.100 00-0C-0C-00-00-01 ping 192.168.1.100 The device responds to the ping in the examples above if the new address was configured.

  • Page 102: Appendix 4. -Register As A Ddns Member

    DDNS service. Registering for a DDNS Enter the URL www.dyndns.com. In the upper right-hand corner of the main page, where there is an item, ”Create Account”, as shown in Figure 1. Figure 1 Create an account After clicking ”Create Account”, you will enter the Create Account page.
  • Page 103 Figure 2 Figure 3 Click “My Services” to enter the service page. Please click the “Add Host Service” item which is below the ”My Hosts“ item, as shown in Figure 4. Click “Add Host Service”, and its service items will appear. The Add Dynamic DNS Host item helps to add a new DDNS.
  • Page 104 Figure 4 Figure 5 All we have to set in this page is the “Hostname” item. The user can choose a Sub Hostname as s/he likes from the right-hand side of the Hostname’s drop-down list. NOTE: You don’t have to set the “IP Address” in the same format as the camera’s IP Address.
  • Page 105 Figure 6...

  • Page 106: Appendix 5. -Mpeg4 Bit Rate Lookup Table Of Ip Camera

    APPENDIX 5. –MPEG4 Bit Rate Lookup Table of IP camera 1. When frame rate is higher than 15 frames/second (15 is not including): Highest High Medium Lowest FULL D1 2.63 2.25 1.75 1.31 0.88 Half D1 1.25 0.75 Half VGA 1.31 1.13 0.88...

  • Page 107: Appendix 6. -Faq

    APPENDIX 6. –FAQ 1. How to disable the DHCP function and use a static IP instead? A：Turn up the “DIP SWITCH” from “3” to “4” and change the relative network settings, the IP Address, NetMask and Gateway on the image web page. 2.

Table of Contents