Page 4
• Do not leave the equipment in a non air‐conditioned environment where the storage temperature may go above 70°C (158°F), as this can cause damage to the equipment. • Gently wipe screen with a clean soft hair lens brush, or a lint‐free cloth. • Do not apply pressure to the screen while cleaning. • Do not spray any liquid directly onto the screen or the casing of the K‐ Monitor Touch POS Monitor. • Chemical cleaners have been reported to cause damage on the screen of the K‐Monitor Touch POS Monitor. • The technical descriptions and specifications of the equipment are subject to change without notice. • For safety reasons, wear gloves when assembling the product. • Patent pending. •...
Page 5
Consult the dealer or an experienced radio/TV technician for help. WARNING: The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Page 6
Preface The WEEE logo (shown at the left) on the product or on its box indicates that this product must not be disposed of or dumped with your other household waste. You are liable to dispose of all your electronic or electrical waste equipment by relocating over to the specified collection point for recycling of such hazardous waste. Isolated collection and proper recovery of your electronic and electrical waste equipment at the time of disposal will allow us to help conserving natural resources. Moreover, proper recycling of the electronic and electrical waste equipment will ensure safety of human health and environment. For more information about electronic and electrical waste equipment disposal, recovery, and collection points, please contact your local city center, household waste disposal service, shop from where you purchased the equipment, or manufacturer of the equipment. ...
Congratulations on your purchase of this touch POS monitor. Your easy‐to‐use touch POS monitor is designed to help you enhance your business flexibility by offering superior customer experience. Model K‐Monitor LCD Panel Size 15 Inches TFT Active matrix type LCD panel Maximum Visual Size 246(H)x184.5(V) mm Maximum Resolution 1024 x 768 Display Color 16.7M (max.) PC Interface Analog VGA Signal Input Connector DB‐Type 15 PIN High Density Female connector Signal Sync TTL positive or negative VGA 640x350 (70/85HZ) VGA 720x400 (70/85HZ) Display Mode VGA 640x480 (60/72/75/85HZ) VGA 800x600 (56/60/72/75/85HZ) XGA 1024x 768 (56/60/72/75/85HZ) Power Supply DC 12V 3.0A 36W ...
Chapter 1 — Welcome The figures below illustrate the components located at the front and rear views of K‐Monitor. NO. DESCRIPTION 1 LCD display 2 MSR module compartment 3 Speaker 4 Power cable 5 DB15 VGA cable 6 Audio In cable 7 USB cable for MSR 8 DB9 (RS232) cable for Touch panel Note: The power cable, VGA cable, audio cable, USB cable, and RS232 cable have been pre‐installed onto the respective connectors on the monitor before product shipment. ...
Page 11
Chapter 1— Welcome You can adjust the LCD panel up to an angle of 90°. ...
Chapter 1 — Welcome NO. ITEM FUNCTION 1 Power button Press to turn the monitor power on or off. LED 2 Show the working status of the display. indicator Press to display the OSD menus on the screen. 3 Menu button In OSD menu, press to select the menu options. In OSD menu, press to increase the value of the 4 + selected menu option. In OSD menu, press to decrease the value of the 5 – selected menu option. Press to automatically resize, center, and fine tune the 6 Auto button video signal to eliminate noise and distortion. ...
Chapter 1 — Welcome Before setting up your touch POS monitor, check that the package contains the Before setting up your touch POS monitor, check that the package contains the following items. If any of the items is missing or damaged, contact your vendor following items. If any of the items is missing or damaged, contact your vendor immediately. immediately. Touch POS Monitor Touch POS Monitor Power Cord Power Cord Magnetic Stripe Magnetic Stripe Reader (optional Reader (optional Accessory Package Driver CD User’s Manual ...
Page 15
This chapter describes how to install the optional accessories on your touch POS monitor for optimal serviceability. Before you start installing K‐Monitor, read the following notices. Do not insert or remove any device or component from the K‐Monitor while the power is turned on. If using K‐Monitor in a dusty environment, clean the monitor regularly. The USB device connector is Hot Swap capable. Do not plug in or unplug any connection except USB devices when the power is on. The spill proof design of K‐Monitor conforms to IP‐43 standard (Front panel only). Always seek the help of authorized service personnel in disassembling the monitor. The manufacturer will not be held responsible in the event of damage caused by an unauthorized person. Before installation or disassembling of the monitor, ensure that the power is turned off. Otherwise, electric shock may occur and may void the warranty. ...
Chapter 2 — Getting Started To connect your monitor to the POS terminal (POS PC), do the following: Connect the power cable into a power outlet. Plug the related cables to the respective connectors on the POS PC as shown. Power Outlet POS PC ...
Page 17
Chapter 2 — Getting Started To install the MSR/SCR device onto the K‐Monitor, do the following: Remove the MSR module compartment (A). Thread the MSR/SCR USB cable through the MSR/SCR bracket (B). Affix the casing screw to the bracket and hook the MSR/SCR device onto the casing screw head as shown (C). Then push down to secure it in place. Secure the MSR/SCR device onto the bracket with one M3 screw (D). ...
Page 18
Chapter 2 — Getting Started Firmly connect the MSR/SCR USB cable to the connector on the right side of the monitor (E). Attach and secure the MSR/SCR device onto the monitor with the two screws (F). ...
Chapter 2 — Getting Started To replace the cable(s), do the following: Carefully place the monitor side down on a cushioned surface to protect the display from damage. Remove the two screws on the back cover. Pull the back cover to the direction of the arrow to remove it. ...
Page 20
Chapter 2 — Getting Started Remove the two screws (M4*10) (A) and two thumbscrews (B) as shown. Remove the connectors cover. ...
Page 21
Chapter 2 — Getting Started Detach the cable(s) that you want to replace. Remove the routing plate. Remove the adapter and route the cable(s) as shown to remove it from the monitor. Routing plate Replace the cable(s) with a new one. Then follow the above‐mentioned steps in reverse to complete the replacement. ...
Page 22
ITEM SPECIFICATIONS Model Name K‐Monitor LCD Panel Size 15 Inches TFT Active matrix type LCD panel Maximal Visual 246(H) x 184.5(V) mm Size Pixel Pitch 0.3075(H) x 0.3075(V) mm Maximal 1024 x 768 Resolution Contrast Ratio 600:1 (Typical) Brightness 250 cd/m Response Time 10 Ms (Typical) Viewing angle +‐ 45 degree (L/R) +30 to ‐10 degree Viewing angle (U/D) Compatible with DDC 1/2B Rule Plug & Play Function Display Color 16.7M (max.) PC Interface Analog VGA Signal Input DB‐Type 15 PIN High Density Female connector Connector Signal Sync TTL positive or negative Display Mode ...
Dimensions (D x W x H) Optional Function 15ʺ 5 Wires Resistive Touch Panel w/Controller ISO Track 1/2/3 MSR (USB type) OPTIONAL DEVICE Magnetic Stripe Reader Note: Specifications are subject to change without notice. PROBLEM SOLUTIONS • Connect the power cord properly. The monitor does not work. • Check if the monitor is turned on or not. Press the Power button to turn on the monitor. • Make sure all cables are connected properly. • Adjust the Brightness in the Brightness and Contrast The display image is too dark. setting menu. • Adjust the volume level in the Sound Control setting The speakers have no sound. menu. ...