1. Manuals
  2. Brands
  3. XAVI Technologies Corp. Manuals
  4. Wireless Router
  5. X7868r
  6. User manual

XAVI Technologies Corp. X7868r User Manual

Adsl wireless router
Hide thumbs Also See for X7868r:
Table of Contents

Advertisement

Quick Links

Download this manual
+
X7868r/X7868r
User's Manual
Version 1.1
- 1 -

Advertisement

Table of Contents
loading

Related Manuals for XAVI Technologies Corp. X7868r

Summary of Contents for XAVI Technologies Corp. X7868r

  • Page 1 X7868r/X7868r User’s Manual Version 1.1 - 1 -...
  • Page 2 X7868r/X7868r User’s Manual Version 1.1 XAVi Technologies Corporation Tel: +886-2-2995-7953 9F, No. 129, Hsing Te Road, Sanchung City, Taipei County 241, Taiwan Copyright © 2006, XAVi Technologies Corporation Information in this manual is subject to change without notice. No part of this manual...

  • Page 3: Table Of Contents

    X7868r/X7868r User’s Manual Version 1.1 CHAPTER 1 – GETTING STARTED OVERVIEW................5 FEATURES ................6 PACKAGING ................7 SAFETY GUIDELINES ..............9 APPEARANCE.................10 HARDWARE INSTALLATION ..........12 MANAGEMENT...............13 VIII DEFAULT VALUES..............14 SOFTWARE UPGRADE ............15 CHAPTER 2 – COMMAND LINE INTERFACE MAIN MENU COMMANDS ............18 LAN MENU COMMANDS ............19 CHAPTER 3 –...
  • Page 4 X7868r/X7868r User’s Manual Version 1.1 1.4 Remote Access…………………………………………..35 1.5 Firmware Update………………………………………..36 1.6 Backup/Restore………………………………………….36 1.7 Restart Router……………………………………………37 2.0 Configuration…………………………………………….38 2.1 Save config……………………………………………….38 2.2 LAN connections………………………………………...38 2.3 EMUX connections………………………………………47 2.4 Portpvc connections……………………………..……….49 2.5 WAN connections……………………………..…………50 2.6 Security…………………………………….….…………91 2.7 802.1x……………………….……………….………….104 2.8 WPA…………………………………..…….…………..106 2.9 Routing Table…………………………..…….…………107 2.10 DHCP server………………………..…….…………...108...

  • Page 5: Chapter 1 - Getting Started

    ANSI T1.413 Issue G.992.1 (X7868r/X7868r ), ITU G.992.2, G.992.3, G.992.4, G.994.5 (X7868r only), and X7868r supports ADSL2 as well. The X7868r/X7868r provides a 10/100BaseTX Ethernet interface on the DTE side. The broadband line interface supports ADSL...

  • Page 6: Features

    X7868r/X7868r User’s Manual Version 1.1 II Features High Speed Asymmetrical Data Transmission on Twisted Copper Pair Wire Service providers can deploy ADSL rapidly over existing wire infrastructure (POTS or ISDN line) Interchangeable between Bridge and Router mode RFC 1483 Bridge and Routing over ATM over ADSL...

  • Page 7: Packaging

    X7868r/X7868r User’s Manual Version 1.1 III Packaging This package consists of the following items: X7868r/X7868r ADSL device unit RJ-45 Cable RJ-11 Cable AC Adapter User’s Manual CD - 7 -...
  • Page 8 X7868r/X7868r User’s Manual Version 1.1 - 8 -...

  • Page 9: Safety Guidelines

    X7868r/X7868r User’s Manual Version 1.1 IV Safety Guidelines In order to reduce the risk of fire, electric shock and injury, please adhere to the following safety guidelines. Carefully follow the instructions in this manual; also follow all instruction labels on this device.

  • Page 10: Appearance

    X7868r/X7868r User’s Manual Version 1.1 V Appearance Front Panel Label Color Description Status Ethernet Green Ethernet transmitting. WLAN Blinking Green WLAN transmitting. Green WLAN port is active Encendido Green Power supply is connected. ADSL Blinking Green Training with DSLAM. Green ADSL link is ready.
  • Page 11 X7868r/X7868r User’s Manual Version 1.1 Rear Panel Label Description POWER Power jack; connect to a power adapter. ETHERNET RJ-45 ports; connect to a PC or LAN. RESET Reset the modem back to factory settings by holding down on this button.

  • Page 12: Hardware Installation

    LAN or a PC with an Ethernet adapter installed. 3. Plug the AC adapter into the AC power socket, and then connect the DC jack to the PWR inlet of X7868r/X7868r Power Supply ADSL Outlet...

  • Page 13: Management

    X7868r/X7868r User’s Manual Version 1.1 VII Management Local Ethernet Port (telnet) – connect the Ethernet port to your local area network or directly to a PC, “Telnet” X7868r/X7868r from any workstation in the LAN. The default local Ethernet IP address is “192.168.1.1”. See Chapter 2, Command Line Interface, for more details.

  • Page 14: Default Values

    X7868r/X7868r User’s Manual Version 1.1 VIII Default Values X7868r/X7868r is pre-configured with the following parameters; you may also re-load the default parameters by pressing the reset button of the modem for about 10 seconds or by using the System Commands link in the Web interface.

  • Page 15: Software Upgrade

    Software upgrade through a DOS prompt Step 1. Extract the ZIP file for updated firmware. Step 2. Connect X7868r/X7868r via the local Ethernet port or remote ADSL link, making sure that the X7868r/X7868r Ethernet IP address and your terminal are properly configured that successfully “ping”...
  • Page 16 Software upgrade through a Web-browser Step 1. Extract the ZIP file for updated firmware. Step 2. Connect X7868r/X7868r via the local Ethernet port or remote ADSL link, making sure that the X7868r/X7868r Ethernet IP address and your terminal are properly configured that successfully “ping”...

  • Page 17: Chapter 2 - Command Line Interface

    Double Click “Hypertrm.exe” Enter a Connection Name Select Icon Click OK 2. Select a port to communicate with X7868r/X7868r Choose TCP/IP and click OK 3. Set Connection Properties Connect To: Host address: 192.168.1.1 Port number: (Choose the port corresponding to the...

  • Page 18: Main Menu Commands

    X7868r/X7868r User’s Manual Version 1.1 CLI Commands 1. Main Menu Commands Type “?” following the “→” to retrieve a list of commands under the main menu to begin the configuration. Command Syntax Description / Parameters → display System info Display current version →...

  • Page 19: Lan Menu Commands

    X7868r/X7868r User’s Manual Version 1.1 RESTART Restarts the modem. Syntax: restart → system config restart Login: RESTORE Sets all configurations to factory default settings. Syntax: restore system config restore factory → Restoring factory defaults... → SAVE Saves the current configuration.
  • Page 20 X7868r/X7868r User’s Manual Version 1.1 Configures the IP address and subnet mask of X7868r/X7868r Syntax: ip set interface <interface> ipaddress <ipaddress>[<subnet mask>] Example: ip set interface eth0 ipaddress 192.168.1.1 255.255.255.0 HOME Returns to the main menu in console Syntax: home home adsl>...
  • Page 21 X7868r/X7868r User’s Manual Version 1.1 acl add write management ipaddr acl delete delete management ipaddr acl disable disable acl fuction acl enable enable acl fuction acl list list management ipaddr agent Get a file from a remote host agent get...
  • Page 22 X7868r/X7868r User’s Manual Version 1.1 classifier list List all classifier profiles classifier profile Commands to edit rules in the specified profile classifier show Show all rules in the specified profile console Console access console enable Enter console mode console process...
  • Page 23 X7868r/X7868r User’s Manual Version 1.1 dnsclient add Add search domains or DNS servers dnsclient clear Clear groups of DNS client settings dnsclient delete Remove specific client settings dnsclient list List DNS client settings dnsrelay DNS relay configuration dnsrelay add Add DNS server address...
  • Page 24 X7868r/X7868r User’s Manual Version 1.1 firewall add …… If you want informations, please press “Tab” key. firewall clear …… firewall delete …… firewall disable …… firewall enable …… firewall list …… firewall set …… firewall show …… firewall status ……...
  • Page 25 X7868r/X7868r User’s Manual Version 1.1 ipoa IP over ATM configuration ipoa add Add IPoA transport ipoa clear Remove all IPoA transports ipoa delete Remove single IPoA transport ipoa list ARP/transport listing ipoa set Set transport parameters ipoa show Display transport details...
  • Page 26 X7868r/X7868r User’s Manual Version 1.1 port Physical port configuration commands port dsl Port name port ethernet Port name port list List ports by type port raw_ethernet Port name port wireless Port name port wlan_filtered Port name pppoa PPP over ATM configuration...
  • Page 27 X7868r/X7868r User’s Manual Version 1.1 radclient get Display the current accounting interval radclient list List the configuration of all the servers radclient set Change accountng interval or the configuration of a radclient server radclient show Show the configuration of a server...
  • Page 28 X7868r/X7868r User’s Manual Version 1.1 security application …… security clear …… security delete …… security disable …… security enable …… security list …… security set …… security show …… security status …… snmp If you want informations, please press “Tab” key.
  • Page 29 X7868r/X7868r User’s Manual Version 1.1 system cpuload Show current CPU loading system delete Remove system users system info Display hardware/software information system legal system list List system information system log Set logging options system restart Restart system (same as pressing reset)
  • Page 30 X7868r/X7868r User’s Manual Version 1.1 wanacl webserver Webserver configuration commands wlanmacfilter set Wireless Mac Filter Table. wlanmacfilter add [mac address] wlanmacfilter delete [mac table list number] wlanmacfilter disable wlanmacfilter disable true or false wlanmacfilter list List Mac Filter Table Configure WPA (Wireless Protected Access) wpa get ……...

  • Page 31: Chapter 3 - Web Management Interface

    Example: X7868r/X7868r : 192.168.1.1 Your PC: 192.168.1.x 3. Connect your PC to X7868r/X7868r and make sure that the PING function is working properly. The default IP address of this device is 192.168.1.1 4. Launch the Web browser (IE or Netscape), and enter the default IP address 192.168.1.1 into the address bar to...

  • Page 32: Login

    X7868r/X7868r User’s Manual Version 1.1 1. Login The Enter Network password window will pop up when starting the configuration. With the window active, type admin for both User name and Password, and then click on the OK button. You can also edit the username and password or add a new profile (see section 4.3 Management for further details).
  • Page 33 X7868r/X7868r User’s Manual Version 1.1 STATUS Show whole situations in this Status page. This page shows the status of your connection. - 33 -...

  • Page 34: Lan Connections

    X7868r/X7868r User’s Manual Version 1.1 LAN connections LAN services currently defined: The default LAN IP interface is eth0, which is shown in the table above. Edit it by using the Change default LAN port IP address button below. Statistics Show all of the Statistic interfaces.

  • Page 35: Users

    X7868r/X7868r User’s Manual Version 1.1 1.1 System Users Authentication This page allows you to control access to your router's console and these configuration web-pages. So you can see Currently Defined Users or Create a new user from this page. 1.2 System/ Event Log...

  • Page 36: One-Click Update

    X7868r/X7868r User’s Manual Version 1.1 1.3 System One-click Update From this page you may update the system software on your network device 1.4 System Remote Access From this page you may temporarily permit remote administration of this network device Remote Access Status Access granted to: all external interfaces on port 0 .
  • Page 37 X7868r/X7868r User’s Manual Version 1.1 1.5 System Firmware Update From this page you may update the system software on your network device to choose a New Firmware Image. 1.6 System Backup/Restore This page allows you to backup the configuration settings to your computer, or restore configuration from your computer.
  • Page 38 X7868r/X7868r User’s Manual Version 1.1 1.7 System Restart Router From this page you may restart your router After restarting, please wait for several seconds to let the system come up. If you would like to reset all configuration to factory default settings, please check the following box:...

  • Page 39: Configuration

    X7868r/X7868r User’s Manual Version 1.1 2.0 Configuration 2.1 Configuration Save config Confirm Save Please confirm that you wish to save the configuration. There will be a delay while saving as configuration information is written to flash. 2.2 Configuration LAN connections...
  • Page 40 X7868r/X7868r User’s Manual Version 1.1 2.2.1.1 WLAN_filtered Edit Edit connection: ‘wlan_filtered’ You can edit Creator, Description, Atm Protocol. Atm Protocol: None, PPPoA, PPPoE, RFC1483-routed, RFC1483-bridge, IpoA. 2.2.1.2 WLAN_Edit Ethernet Enabled: true, false - 40 -...
  • Page 41 X7868r/X7868r User’s Manual Version 1.1 2.2.1.3 WLAN_Edit Ethernet Channel Edit Port and see Port Class. 2.2.1.4 WLAN_Edit Classifier Edit Clsfr Profile and see Clsfr Encap. - 41 -...
  • Page 42 X7868r/X7868r User’s Manual Version 1.1 2.2.1.5 WLAN_Edit Bun Vector Attr Edit the Value of Bn Vector Attr. 2.2.1.6 WLAN_Edit Scheduler Edit the value of Scheduler Profile. - 42 -...
  • Page 43 X7868r/X7868r User’s Manual Version 1.1 2.2.1.7.1 Edit Bridge Interface Edit Name, Ether Filter Type, Port Filter, Port Filter2, Port filter3, Eport Flag, Enabled and see Port ID, In Frames Count,, out Frames Count, Transit Delay Discards Count, Buf Overflow Discards Count.
  • Page 44 X7868r/X7868r User’s Manual Version 1.1 2.2.1.7.3 Edit Ethernet Edit Enabled and see If In Octets, If Out Octets, If In Errors, If Out Errors, Packets Sent, Good Packets, Channel Snmp If Index, Version, Termination. Enabled: true, false 2.2.2.1 Edit Service Edit connection:’emux’...
  • Page 45 X7868r/X7868r User’s Manual Version 1.1 2.2.2.2 Edit Emux Edit Group, Enabled and see If In Octets, If Out Octets, If In Errors, If Out Errors, Packets Sent, Good Packets, Channel Snmp If Index, Version, Termination. Enabled: true, false 2.2.2.3 Edit Emux Channel Edit Txport, Rxport, Port and see Port Class.
  • Page 46 X7868r/X7868r User’s Manual Version 1.1 2.2.2.4 Edit Classifier Edit Clsfr Profile and see Clsfr Encap. 2.2.2.5 Edit Bun Vector Attr Edit the Value of Bun Vector Attr. 2.2.2.6 Edit Scheduler Edit the Value of Sch Profile. - 46 -...
  • Page 47 X7868r/X7868r User’s Manual Version 1.1 2.2.2.7.1 Edit Bridge Interface Edit Name, Ether Filter Type, Port Filter, Port Filter2, Port Filter3, Eport Flag, Enabled and see Port Id, In Frames Count, Out Frames Count, Transit Delay Discards Count, Buf Overflow Discards Count, Layer2Session.

  • Page 48: Emux Connections

    X7868r/X7868r User’s Manual Version 1.1 2.2.2.7.3 Edit Emux Edit Group, Enabled and see If In Octets, If Out Octets, If In Errors, If Out Errors, Packets Sent, Good Packets, Channel Snmp If Index, Version, Termination. Enabled: true, false 2.3 Configuration EMUX connections You can Create Vlan Group and Create Wireless.
  • Page 49 X7868r/X7868r User’s Manual Version 1.1 2.3.1 WLAN_Filtered Edit VLAN Group ( Can not modify ) It is fixed after you creating these Groups. 2.3.2 EMUX Edit VLAN Group It is fixed after you creating these Groups. - 49 -...

  • Page 50: Portpvc Connections

    X7868r/X7868r User’s Manual Version 1.1 2.4 Configuration Portpvc connections Show all of Port-PVC names. 2.4.1 Configuration Portpvc connections / Edit Port PVC Edit wlan_filtered. Wlan_filtered: All, wlan_filtered, emux. - 50 -...

  • Page 51: Wan Connections

    X7868r/X7868r User’s Manual Version 1.1 2.4.2 Configuration Portpvc connections / Edit Port PVC Edit emux. emux: All, wlan_filtered, emux 2.5 Configuration WAN connections Edit WAN services currently defined. Or Create a new service. - 51 -...
  • Page 52 X7868r/X7868r User’s Manual Version 1.1 2.5.1 Create a new service 2.5.1.1 Create a new service RFC 1483 routed Edit Description, VPI, VCI, Encapsulation method, Use DHCP, WAN IP address, Enable NAT on this interface. Encapsulation method: LLC/SNAP, VcMux(null) 2.5.1.2 Create a new service RFC 1483 bridged Edit Description, VPI, VCI, Encapsulation method.
  • Page 53 X7868r/X7868r User’s Manual Version 1.1 2.5.1.3 Create a new service PPPoA routed Edit Description, VPI, VCI, PPPoA Auto Connect, Discover IP Subnet from IPCP, WAN IP address, Enable NAT on this interface, LLC header mode, HDLC header mode, No authentication, PAP, CHAP, User name, Password, User Idle Timeout (in minutes).
  • Page 54 X7868r/X7868r User’s Manual Version 1.1 2.5.1.4 Create a new service MER(bridge with NAT) Edit Description, VPI, VCI, Encapsulation method, Use DHCP, WAN IP address, Enable NAT on this interface. Encapsulation method: LLC/SNAP, VcMux(null) 2.5.1.5 Create a new service IpoA routed Edit Description, VPI, VCI, Encapsulation method, Use DHCP, WAN IP address, Enable NAT on this interface.
  • Page 55 X7868r/X7868r User’s Manual Version 1.1 2.5.1.6 Create a new service PPPoE routed Edit Description, VPI, VCI, PPPoE Auto Connect, Discover IP Subnet from IPCP, WAN IP address, Enable NAT on this interface, Access concentrator, Access concentrator, Service name, LLC header mode, HDLC header mode, No authentication, PAP, CHAP, User name, Password, User Idle Timeout (in minutes).
  • Page 56 X7868r/X7868r User’s Manual Version 1.1 2.5.2 Edit a service 2.5.2.1 Edit a service RFC 1483 routed IF need, you can edit WAN services currently defined. 2.5.2.1.1 Edit a service RFC 1483 routed/Edit Service Edit Creator, Description, Atm Protocol. - 56 -...
  • Page 57 X7868r/X7868r User’s Manual Version 1.1 2.5.2.1.2 Edit a service RFC 1483 routed/Edit RFC1483 Edit Mode, MAC, Type, Snmp If Index, If In Octets, If Out Octets, If In Errors, If Out Errors, Packets Sent, Good Packets, Channel Snmp If Index, Version, Enabled, and see Termination.
  • Page 58 X7868r/X7868r User’s Manual Version 1.1 2.5.2.1.3 Edit a service RFC 1483 routed /Edit Atm Channel Edit Tx Vci, Tx Vpi, Rx Vci, Rx Vpi, Peak Cell Rate, Burst Tolerance, Max Cell Rate, Max Burst Size, Sustainable Cell Rate, Packet Priority Levels, ATM Traffic Class, Port and see Port Class.
  • Page 59 X7868r/X7868r User’s Manual Version 1.1 2.5.2.1.4 Edit a service RFC 1483 routed /Edit Classifier Edit Clsfr Profile and see Clsfr Encap. 2.5.2.1.5 Edit a service RFC 1483 routed /Edit Bun Vector Attr Edit the value of Bun Vector Attr. - 59 -...
  • Page 60 X7868r/X7868r User’s Manual Version 1.1 2.5.2.1.6 Edit a service RFC 1483 routed /Edit Scheduler Edit Sch Profile. 2.5.2.1.7 Edit a service RFC 1483 routed /Edit Ip Interface Edit Ipaddr, Mask, Dhcp, MTU, Source Addr Validation, Icmp Router Advertise, Real Interface, Enabled and see Name, Snmp If Index, Layer2Session.
  • Page 61 X7868r/X7868r User’s Manual Version 1.1 2.5.2.2 Edit a service RFC 1483 bridged Edit RFC1483bridge service of the WAN connection. 2.5.2.2.1 Edit a service RFC 1483 bridged /Edit Service Edit Creator, Description, Atm Protocol. - 61 -...
  • Page 62 X7868r/X7868r User’s Manual Version 1.1 2.5.2.2.2 Edit a service RFC 1483 bridged /Edit RFC1483 Edit Mode, MAC, Type, Snmp If Index, Enabled, And see If In Octets, If Out Octets, If In Errors, If Out Errors, Packets Sent, Good Packets, Channel Snmp If Index, Version, Termination.
  • Page 63 X7868r/X7868r User’s Manual Version 1.1 2.5.2.2.3 Edit a service RFC 1483 bridged /Edit Atm Channel Edit Tx Vci, Tx Vpi, Rx Vci, Rx Vpi, Peak Cell Rate, Burst Tolerance, Max Cell Rate, Max Burst Size, Sustainable Cell Rate, Packet Priority Levels, ATM Traffic Class, Port and see Port Class.
  • Page 64 X7868r/X7868r User’s Manual Version 1.1 2.5.2.2.4 Edit a service RFC 1483 bridged /Edit Classifier Edit Clsfr Profile and see Clsfr Encap. 2.5.2.2.5 Edit a service RFC 1483 bridged /Edit Bun Vector Attr Edit the value of Bun Vector Attr. - 64 -...
  • Page 65 X7868r/X7868r User’s Manual Version 1.1 2.5.2.2.6 Edit a service RFC 1483 bridged /Edit Scheduler Edit Sch Profile. - 65 -...
  • Page 66 X7868r/X7868r User’s Manual Version 1.1 2.5.2.2.7 Edit a service RFC 1483 bridged /Edit Bridge Interface Edit Name, Ether Filter Type, Port Filter, Port Filter2, Port Filter3, Eport Flag, Enabled and see Port Id, In Frames Count, Out Frames Count, Transit Delay Discards Count, Buf Overflow Discards Count, Layer2Session.
  • Page 67 X7868r/X7868r User’s Manual Version 1.1 2.5.2.3 Edit a service PPPoA routed Edit a service PPPoA routed of the WAN connection. 2.5.2.3.1 Edit a service PPPoA routed /Edit Service Edit Creator, Description, Atm Protocol. - 67 -...
  • Page 68 X7868r/X7868r User’s Manual Version 1.1 2.5.2.3.2 Edit a service PPPoA routed /Edit PPP You can see all settings of PPPoA from this page. And Edit values where you can modify and choose them. - 68 -...
  • Page 69 X7868r/X7868r User’s Manual Version 1.1 2.5.2.3.3 Edit a service PPPoA routed /Edit Atm Channel The setting about ATM Channel. - 69 -...
  • Page 70 X7868r/X7868r User’s Manual Version 1.1 2.5.2.3.4 Edit a service PPPoA routed /Edit Classifier Edit Clsfr Profile and see Clsfr Encap. 2.5.2.3.5 Edit a service PPPoA routed Edit the value of Bun Vector Attr. - 70 -...
  • Page 71 X7868r/X7868r User’s Manual Version 1.1 2.5.2.3.6 Edit a service PPPoA routed /Edit Scheduler Edit Sch Profile Value of the Scheduler. - 71 -...
  • Page 72 X7868r/X7868r User’s Manual Version 1.1 2.5.2.3.7 Edit a service PPPoA routed /Edit IP Interface Edit Ipaddr, Mask, Dhcp, MTU, Source Addr Validation, Icmp Router Advertise, Enabled and see Name, Snmp If Index, Layer2Session. - 72 -...
  • Page 73 X7868r/X7868r User’s Manual Version 1.1 2.5.2.4 Edit a service MER(bridge with NAT) Edit current WAN connection in a service MER. 2.5.2.4.1 Edit a service MER(bridge with NAT) /Edit Service Edit Creator, Description, Atm Protocol. - 73 -...
  • Page 74 X7868r/X7868r User’s Manual Version 1.1 2.5.2.4.2 Edit a service MER(bridge with NAT) /Edit RFC1483 Edit Mode, MAC, Type, Snmp If Index, Enabled, And see If In Octets, If Out Octets, If In Errors, If Out Errors, Packets Sent, Good Packets, Channel Snmp If Index, Version, Termination.
  • Page 75 X7868r/X7868r User’s Manual Version 1.1 2.5.2.4.3 Edit a service MER(bridge with NAT) \Edit Atm Channel Edit Tx Vci, Tx Vpi, Rx Vci, Rx Vpi, Peak Cell Rate, Burst Tolerance, Max Cell Rate, Max Burst Size, Sustainable Cell Rate, Packet Priority Levels, ATM Traffic Class, Port and see Port Class.
  • Page 76 X7868r/X7868r User’s Manual Version 1.1 2.5.2.4.4 Edit a service MER(bridge with NAT) /Edit Classifier Edit Clsfr Profile and see Clsfr Encap. 2.5.2.4.5 Edit a service MER(bridge with NAT) /Edit Bun Vector Attr Edit the Value of Bun Vector Attr. - 76 -...
  • Page 77 X7868r/X7868r User’s Manual Version 1.1 2.5.2.4.6 Edit a service MER(bridge with NAT) /Edit Scheduler Edit Sch Profile. - 77 -...
  • Page 78 X7868r/X7868r User’s Manual Version 1.1 2.5.2.4.7 Edit a service MER(bridge with NAT) /Edit Edit Ipaddr, Mask, Dhcp, MTU, Source Addr Validation, Icmp Router Advertise, Enabled and see Name, Snmp If Index, Layer2Session. - 78 -...
  • Page 79 X7868r/X7868r User’s Manual Version 1.1 2.5.2.5 Edit a service IpoA routed Edit the current WAN connection with a service IpoA routed. 2.5.2.5.1 Edit a service IpoA routed/Edit Service Edit Creator, Description, Atm Protocol. - 79 -...
  • Page 80 X7868r/X7868r User’s Manual Version 1.1 2.5.2.5.2 Edit a service IpoA routed/Edit IPoA Edit SVC, Atmarp, Lifetime, Snmp If Index, Enabled and see If In Octets, If Out Octets, If In Errors, If Out Errors, Packets Sent, Good Packets, Channel Snmp If Index, Version, Termination.
  • Page 81 X7868r/X7868r User’s Manual Version 1.1 2.5.2.5.3 Edit a service IpoA routed/Edit Atm Channel Edit Tx Vci, Tx Vpi, Rx Vci, Rx Vpi, Peak Cell Rate, Burst Tolerance, Max Cell Rate, Max Burst Size, Sustainable Cell Rate, Packet Priority Levels, ATM Traffic Class, Port and see Port Class.
  • Page 82 X7868r/X7868r User’s Manual Version 1.1 2.5.2.5.4 Edit a service IpoA routed/Edit Classifier 2.5.2.5.5 Edit a service IpoA routed/Edit Bun Vector Attr - 82 -...
  • Page 83 X7868r/X7868r User’s Manual Version 1.1 2.5.2.5.6 Edit a service IpoA routed/Edit Scheduler Edit Sch Profile. - 83 -...
  • Page 84 X7868r/X7868r User’s Manual Version 1.1 2.5.2.5.7 Edit a service IpoA routed/Edit Ip Interface Edit Ipaddr, Mask, Dhcp, MTU, Source Addr Validation, Icmp Router Advertise, Real Interface, Enabled and see Name, Snmp If Index, Layer2Session. Dhcp: true, false Source Addr Validation: false, true...
  • Page 85 X7868r/X7868r User’s Manual Version 1.1 2.5.2.6 Edit a service PPPoE routed Edit a WAN connection of the service PPPoE routed. 2.5.2.6.1 Edit a service PPPoE routed/Edit Service Edit Creator, Description, Atm Protocol. - 85 -...
  • Page 86 X7868r/X7868r User’s Manual Version 1.1 2.5.2.6.2 Edit a service PPPoE routed/Edit PPPoE Edit and see whole settings of the PPPoE routed. - 86 -...
  • Page 87 X7868r/X7868r User’s Manual Version 1.1 2.5.2.6.3 Edit a service PPPoE routed/Edit Atm Channel Edit Tx Vci, Tx Vpi, Rx Vci, Rx Vpi, Peak Cell Rate, Burst Tolerance, Max Cell Rate, Max Burst Size, Sustainable Cell Rate, Packet Priority Levels, ATM Traffic Class, Port and see Port Class.
  • Page 88 X7868r/X7868r User’s Manual Version 1.1 2.5.2.6.4 Edit a service PPPoE routed/Edit Classifier Edit Clsfr Profile, Clsfr Encap. 2.5.2.6.5 Edit a service PPPoE routed /Edit Bun Vector Attr Edit the Value of the Bun Vector Attr. - 88 -...
  • Page 89 X7868r/X7868r User’s Manual Version 1.1 2.5.2.6.6 Edit a service PPPoE routed/Edit Scheduler Edit Sch Profile. 2.5.2.7.1 Edit a service PPPoE routed/ Edit Ip Interface Edit Ipaddr, Mask, Dhcp, MTU, Source Addr Validation, Icmp Router Advertise, Real Interface, Enabled and see Name, Snmp If Index, Layer2Session.
  • Page 90 X7868r/X7868r User’s Manual Version 1.1 2.5.2.7.2 Edit a service PPPoE routed /Edit Tcp Mss Clamp Edit Tcp Mss Clamp. TCP MSS Clamp: true, false 2.5.2.7.3 Edit a service PPPoE routed /Edit Rip Versions Edit Accept V1, Accept V2, Send V1, Send V2, Send Multicast...
  • Page 91 X7868r/X7868r User’s Manual Version 1.1 2.5.2.7.4 Edit a service PPPoE routed /Edit NAT Edit Nat Enabled. Nat Enabled: true, false 2.5.2.7.5 Edit a service PPPoE routed /Edit PPPoE Edit and see whole settings of PPPoE. - 91 -...

  • Page 92: Security

    X7868r/X7868r User’s Manual Version 1.1 2.6 Configuration Security You can choose what Security State, Security Level, Security Interfaces, Policies, Triggers, Intrusion Detection, Loggin you want to set it. - 92 -...
  • Page 93 X7868r/X7868r User’s Manual Version 1.1 2.6.1 Configuration Security /Advanced NAT Configuration: ppp-0 Add Globa Address Pools or Add Reserved Mapping from this page. - 93 -...
  • Page 94 X7868r/X7868r User’s Manual Version 1.1 2.6.1.1 Configuration Security /Advanced NAT Configuration: ppp-0 /NAT Add Global Address Pool: ppp-0 Edit Interface Type, Use Subnet Configuration, Ip Address, Subnet Mask/IP Address 2. Use Subnet Configuration: Use Subnet Mask, Use IP Address Range...
  • Page 95 X7868r/X7868r User’s Manual Version 1.1 2.6.1.2 Configuration Security /Advanced NAT Configuration: ppp-0 /NAT Add Reserved Mapping:ppp-0 Edit IP Addresses, Transport, External Port Range, Internal Port Range. (Set to 0.0.0.0 to use the primary IP address of the interface "ppp-0") - 95 -...
  • Page 96 X7868r/X7868r User’s Manual Version 1.1 2.6.2 Configuration Security /Security Policy Configuration Edit Policy Configuration. Port Filters, Host Validators - 96 -...
  • Page 97 X7868r/X7868r User’s Manual Version 1.1 2.6.2.1 Configuration Security /Security Policy Configuration/Port Filters Show or delete Firewall Port Filters. And you can add TCP or UDP Filter, Add Raw IP Filter. 2.6.2.1.1 Configuration Security /Security Policy Configuration/Port Filters /Firewall Add TCP/UDP Port Filter Edit a policy.

  • Page 98: Configuration Security

    X7868r/X7868r User’s Manual Version 1.1 2.6.2.1.2 Configuration Security /Security Policy Configuration/Port Filters /Firewall Add Raw IP Filter Edit a policy. - 98 -...
  • Page 99 X7868r/X7868r User’s Manual Version 1.1 2.6.2.2 Configuration Security /Security Policy Configuration/Host Validators Add Host Validators. - 99 -...
  • Page 100 X7868r/X7868r User’s Manual Version 1.1 2.6.2.2.1 Configuration Security /Security Policy Configuration/Host Validator /Add Host Validator Let you know about the setting of : Firewall Add Host Validator: external-internal - 100 -...
  • Page 101 X7868r/X7868r User’s Manual Version 1.1 2.6.3 Configuration Security /Security Trigger Configuration /Current Security Trigger 2.6.3.1 Configuration Security /Security Trigger Configuration /Security:Add Trigger Add Trigger. - 101 -...
  • Page 102 X7868r/X7868r User’s Manual Version 1.1 2.6.4 Configuration Security /Firewall Configure Intrusion Detection Edit Firewall Configure Intrusion Detection. - 102 -...
  • Page 103 X7868r/X7868r User’s Manual Version 1.1 2.6.5 Configuration Security /Security Logging Configuration Edit Security Logging Configuration. - 103 -...
  • Page 104 X7868r/X7868r User’s Manual Version 1.1 2.6.6 Configuration Security /Edit Firewall Management Station Edit Firewall Management Station. - 104 -...
  • Page 105 X7868r/X7868r User’s Manual Version 1.1 2.7 Configuration 802.1x Configure IEEE 802.1x Authentication for the wireless port. - 105 -...
  • Page 106 X7868r/X7868r User’s Manual Version 1.1 2.7.1 Configuration 802.1x / View advanced attributes Edit 802.1x Authenticator - 106 -...
  • Page 107 X7868r/X7868r User’s Manual Version 1.1 2.8 Configuration WPA Edit WPA Passphrase 2.8.1 Configuration WPA Edit WPA Passphrase - 107 -...
  • Page 108 X7868r/X7868r User’s Manual Version 1.1 2.9 Edit Routes Edit currently routes or Create new Ip V4Route. 2.9.1 Edit Routes/ Create Ip V4Route - 108 -...

  • Page 109: Dhcp Server

    X7868r/X7868r User’s Manual Version 1.1 2.10 DHCP server This page allows creation of DHCP server subnets and DHCP server fixed host IP/MAC mappings. You may also enable and disable the DHCP server from here. The DHCP server is currently showed status.
  • Page 110 X7868r/X7868r User’s Manual Version 1.1 2.10.1 DHCP Server/Edit DHCP server subnet - 110 -...
  • Page 111 X7868r/X7868r User’s Manual Version 1.1 2.10.1 DHCP Server/Create DHCP server This page allows you to set up a new DHCP server configuration option that will be sent to DHCP clients on this subnet. Choose which option you would like to configure using the drop down list.
  • Page 112 X7868r/X7868r User’s Manual Version 1.1 2.10.2 DHCP Server/Create new DHCP server subnet This page allows you to set up a new DHCP server subnet so that the system can assign IP address, subnet mask and option configuration parameters to DHCP clients.

  • Page 113: Dhcp Server

    X7868r/X7868r User’s Manual Version 1.1 2.10.2 DHCP Server /Create new DHCP server fixed host IP/MAC mapping Add new mapping Define your new fixed mapping here. The IP address you choose will be given to the host with the MAC address you specify. The IP address must not clash with an IP address already present in a dynamic address range.

  • Page 114: Dns Client

    X7868r/X7868r User’s Manual Version 1.1 2.11 DNS Client Edit DNS servers or Domain search order. - 114 -...

  • Page 115: Dns Relay

    X7868r/X7868r User’s Manual Version 1.1 2.12 DNS Relay This page allows you to enter a list of DNS server IP addresses that the DNS relay can forward DNS queries to. It also allows access to the DNS relay LAN database..
  • Page 116 X7868r/X7868r User’s Manual Version 1.1 2.12.1 DNS Relay/DNS relay local LAN database This page allows you to view and edit the list of hosts and IP addresses present on the local network. Global database settings Specify the LAN domain name here. Please note that entries in the local database will not function until a domain name is specified.
  • Page 117 X7868r/X7868r User’s Manual Version 1.1 2.12.1.1 DNS Relay/DNS relay local LAN database /Create new DNS relay local LAN database entry This page lets you enter the details of a new device on the local LAN. You need to type in the name of the device and its IP address.
  • Page 118 X7868r/X7868r User’s Manual Version 1.1 2.12.1.1.1 DNS Relay/DNS relay local LAN database /Create new DNS relay local LAN database entry /Extra host names and IP addresses This page allows you to view and edit a list of additional host names and IP addresses for the local LAN host paul.

  • Page 119: Sntp Client

    X7868r/X7868r User’s Manual Version 1.1 2.13 SNTP client - 119 -...

  • Page 120: Igmp Proxy

    X7868r/X7868r User’s Manual Version 1.1 2.14 IGMP Proxy Edit Upstream Interface. - 120 -...

  • Page 121: Wireless Mac Filter

    X7868r/X7868r User’s Manual Version 1.1 2.15 Wireless Mac Filter Wireless Mac Address Access Configuration 2.16 RADIUS Client RADIUS Client Configuration - 121 -...
  • Page 122 X7868r/X7868r User’s Manual Version 1.1 2.16.1 RADIUS Client/ View Service Add Authentication Servers or Add Accounting Servers. - 122 -...

  • Page 123: Adsl

    X7868r/X7868r User’s Manual Version 1.1 2.17.Port/ADSL Note that the Reset Defaults option will not take effect until you save configuration and reboot. - 123 -...
  • Page 124 X7868r/X7868r User’s Manual Version 1.1 2.17.1.Port/ADSL/View advanced attributes advanced attributes. Edit or see whole - 124 -...

  • Page 125: Switch Ether

    X7868r/X7868r User’s Manual Version 1.1 2.17.2 Port/ Switch Ether See Ethernet Configuration status. 2.17.3 Port/ WireLess The Wireless Disable true. 2.17.3 Port/ WireLess Note that the Reset Defaults option will not take effect until you save configuration and reboot. - 125 -...
  • Page 126 X7868r/X7868r User’s Manual Version 1.1 The Wireless Disable false. --- The End --- - 126 -...

Table of Contents